Magnetically induced non-Faraday nonreciprocity in a fiber-optic gyroscope

Optical phase nonreciprocity is found to appear in fiber-optic gyroscopes as a result of a magnetically induced distortion of a propagating fiber mode. It is shown that this nonreciprocity places a limitation on the magnetic stability of a gyroscope.     

Protecting local access telecommunications networks: Toward a minimum-cost solution

The problem of designing fibre-optic networks for local-access telecommunications generates (at least) three non-trivial subproblems. In the first of these subproblems one must determine how many fibre-optic cables (fibres) are required at either end of a street. In the next subproblem a minimum-cost network must be designed to support the fibres. The network must also provide distinct paths from either end of the street to the central exchange(s). Finally, the fibre-optic cables must be placed in protective covers. These covers are available in a number of different sizes, allowing some flexibility when covering each section of the network. In this paper we describe a dynamic programming (DP) formulation for finding a minimum-cost (protective) covering for the network (the third of the subproblems). This problem is a generalised set covering problem with side constraints and is further complicated by the introduction of fixed and variable welding costs. The DP formulation selects covers along each arc (in the network), but cannot exactly model the fixed costs and so does not guarantee optimality. We also describe an integer programming (IP) formulation for assessing the quality of the DP solutions. The cost of the networks constructed by the IP model is less than those designed using the DP model, but the saving is not significant for the problems examined (less than 0.1%). This indicates that the DP model will generally give very good solutions. Furthermore, as the problem dimensions grow, DP gives significantly better solution times than IP.     

Extracting Light from Polymer Light‐Emitting Diodes Using Stamped Bragg Gratings

In this paper, we describe a method for increasing the external efficiency of polymer light‐emitting diodes (LEDs) by coupling out waveguided light with Bragg gratings. We numerically model the waveguide modes in a typical LED structure and demonstrate how optimizing layer thicknesses and reducing waveguide absorption can enhance the grating outcoupling. The gratings were created by a soft‐lithography technique that minimizes changes to the conventional LED structure. Using one‐dimensional and two‐dimensional gratings, we were able to increase the forward‐directed emission by 47 % and 70 %, respectively, and the external quantum efficiency by 15 % and 25 %.     

Reliability studies of MOCVD TiSiN and EnCoRe Ta(N)/Ta

Passivated single damascene copper SiO₂ damascene lines were evaluated in combination with TiSiN and Ta(N)/Ta diffusion barriers. Leakage current, breakdown and time-dependent dielectric breakdown properties were investigated on a wafer level basis for temperatures ranging between room temperature and 150 °C. It is found that the leakage performance of the wafers with a TiSiN barrier is better at room temperature, but at 150 °C the performance levels out with Ta(N)/Ta. Time-dependent dielectric breakdown measurements at 150 °C show that the lifetime of the interconnect is higher with the selected Ta(N)/Ta barrier than for TiSiN.     

Intelligent process analytics for CRM

Many organisations use decision models in their processes such as tables or trees to provide decision support to their operational divisions. For example, in fault management, customer contact centre operators usually use a decision model in the form of prescribed interviews. Based on the answers given by customers, the operator navigates through the decision model to reach an assessment of the problem. In order to achieve customer satisfaction and operational excellence, it is very important to constantly monitor the performance of a decision model not only on an overall level, but also on the level of individual decisions. In this paper we present a configurable business process analytics tool, known as the intelligent Universal Service Management System, that constantly monitors decision data and is capable of optimising the decisions based on high-level business objectives. We explain the various features of the software and show how it can be used to optimise decision processes. We also show how we can easily provide a customised version to monitor the performance of provision processes.     

X-ray or UV adjustment of MOS threshold voltage: Analytical and numerical modeling

A model is formulated that describes how radiation-induced charge accumulates in the gate oxide of a MOS structure and how it decays through tunneling and thermal emission. The model is used in a numerical analysis of the x-ray or UV adjustment of threshold voltage in MOS-circuit manufacture. The limits of this process technique are evaluated.     

1/f noise in large-area Hg<Subscript>1−x</Subscript>Cd<Subscript>x</Subscript>Te photodiodes

The 1/f noise in photovoltaic (PV) molecular-beam epitaxy (MBE)-grown Hg_1−xCd_xTe double-layer planar heterostructure (DLPH) large-area detectors is a critical noise component with the potential to limit sensitivity of the cross-track infrared sounder (CrIS) instrument. Therefore, an understanding of the origins and mechanisms of noise currents in these PV detectors is of great importance. Excess low-frequency noise has been measured on a number of 1000-μm-diameter active-area detectors of varying “quality” (i.e., having a wide range of I-V characteristics at 78 K). The 1/f noise was measured as a function of cut-off wavelength under illuminated conditions. For short-wave infrared (SWIR) detectors at 98 K, minimal 1/f noise was measured when the total current was dominated by diffusion with white noise spectral density in the mid-10⁻¹⁵A/Hz^1/2 range. For SWIR detectors dominated by other than diffusion current, the ratio, α, of the noise current in unit bandwidth i_n(f = 1 Hz, V_d = −60 mV, and Δf = 1 Hz) to dark current I_d(V_d = −60 mV) was α_SW-d = i_n/I_d ∼ 1 × 10⁻³. The SWIR detectors measured at 0 mV under illuminated conditions had median α_SW-P = i_n/I_ph ∼ 7 × 10⁻⁶. For mid-wave infrared (MWIR) detectors, α_MW-d = i_n/I_d ∼ 2 × 10⁻⁴, due to tunneling current contributions to the 1/f noise. Measurements on forty-nine 1000-μm-diameter MWIR detectors under illuminated conditions at 98 K and −60 mV bias resulted in α_MW-P = i_n/I_ph = 4.16 ± 1.69 × 10⁻⁶. A significant point to note is that the photo-induced noise spectra are nearly identical at 0 mV and 100 mV reverse bias, with a noise-current-to-photocurrent ratio, α_MW-P, in the mid 10⁻⁶ range. For long-wave infrared (LWIR) detectors measured at 78 K, the ratio, α_LW-d = i_n/I_d ∼ 6 × 10⁻⁶, for the best performers. The majority of the LWIR detectors exhibited α_LW-d on the order of 2 × 10⁻⁵. The photo-induced 1/f noise had α_LW-P = i_n/I_ph ∼ 5 × 10⁻⁶. The value of the noise-current-to-dark-current ratio, α appears to increase with increasing bandgap. It is not clear if this is due to different current mechanisms impacting 1/f noise performance. Measurements on detectors of different bandgaps are needed at temperatures where diffusion current is the dominant current. Excess low-frequency noise measurements made as a function of detector reverse bias indicate 1/f noise may result primarily from the dominant current mechanism at each particular bias. The 1/f noise was not a direct function of the applied bias.     

Effect of Sb implantation on copper silicides formation and morphology after annealing of Cu/Si structures

In this work, the solid state reaction between a thin film of copper and silicon has been studied using Rutherford backscattering spectroscopy, X-ray diffraction, scanning electron microscopy and microprobe analysis. Cu films of 400 and 900 Å thicknesses are thermally evaporated on Si(1 1 1) substrates, part of them had previously been implanted with antimony ions of 5×10¹⁴ or 5×10¹⁵ at. cm⁻² doses. The samples are heat-treated in vacuum at temperatures in the range 200–700 °C for various times. The results show the growth and formation of Cu₃Si and Cu₄Si silicides under crystallites shape dispatched on the sample surface, independently of the implantation dose. On the other hand, it is established that the copper layer is less and less consumed as the antimony dose increases, resulting in the accumulation of Sb⁺ ions at silicide/Si interface and in the silicide layer close to surface. The exposure of samples to air at room temperature shows the stability of Cu₄Si phase whereas the Cu₃Si silicide disappears to the benefit of the silicon dioxide formation. The observed phenomena are discussed.     

Training and optimization of an artificial neural network controlling a hybrid power filter

A hybrid power compensator (HPC) consisting of a static VAr compensator and a dynamic compensator needs to be optimally controlled during the compensation of nonlinear loads. The HPC must be controlled to meet minimum requirements in terms of power factor and harmonic distortion, while at the same time minimizing its total cost. An artificial neural network (ANN) is used to control the HPC amidst a very dynamic power system environment. The performance of a reference ANN is evaluated while controlling an HPC connected to a typical nonlinear industrial load. The training and performance of the ANN is then optimized in terms of training set size, training set packing and ANN topology and the performance compared to the reference ANN. This paper highlights the importance of optimising the mentioned ANN parameters to achieve optimum ANN training and modeling accuracy. The results obtained reveals that the application of an ANN in controlling an HPC is feasible given that the ANN parameters are chosen appropriately.     

Synthesis of ZSM‐5 Films and Monoliths with Bimodal Micro/Mesoscopic Structures

A route to synthesize ZSM‐5 crystals with a bimodal micro/mesoscopic pore system has been developed in this study; the successful incorporation of the mesopores within the ZSM‐5 structure was performed using tetrapropylammonium hydroxide (TPAOH)‐impregnated mesoporous materials containing carbon nanotubes in the pores, which were encapsulated in the ZSM‐5 crystals during a solid rearrangement process within the framework. Such mesoporous ZSM‐5 zeolites can be readily obtained as powders, thin films, or monoliths.