The First Template‐Free Growth of Crystalline Silicon Microtubes

A simple template‐free high‐temperature evaporation method was developed for the growth of crystalline Si microtubes for the first time. As‐grown Si microtubes were characterized using X‐ray diffraction, scanning electron microscopy, transmission electron microscopy, and room‐temperature photoluminescence. The lengths of the Si tubes can reach several hundreds of micrometers; some of them have lengths on the order of millimeters. Each tube has a uniform outer diameter along its entire length, and the typical outer diameter is ≈ 2–3 μm. Most of the tubes have a wall thickness of ≈ 400–500 nm, though a considerable number of them exhibit a very thin wall thickness of ≈ 50 nm. Room‐temperature photoluminescence measurement shows the as‐synthesized Si microtubes have two strong emission peaks centered at ≈ 589 nm and ≈ 617 nm and a weak emission peak centered at ≈ 455 nm. A possible mechanism for the formation of these Si tubes is proposed. We believe that the present discovery of the crystalline Si microtubes will promote further experimental studies on their physical properties and smart applications.     

High dynamic range InP HBT delta-sigma analog-to-digital converters

To date, the development of multifunction multicarrier digital receivers for cellular base station and military communications applications has been limited by the demanding dynamic range requirements for the analog-to-digital converter (ADC). The use of oversampling delta-sigma modulators provides a promising approach to overcoming the dynamic range barriers Nyquist-rate converters face in the same applications. This paper discusses issues involved in the design of high-speed high dynamic range wide-band delta-sigma ADCs for such communications applications. Test results of prototype designs are also presented. The delta-sigma modulators described in this paper operate at sampling frequencies ranging from 1 to 2.5 GHz with center frequencies ranging from dc to 100 MHz, providing between 74 and 84.2 dB signal-to-noise ratio (12 and 13.7 bits) for bandwidths of 25 and 12.5 MHz, respectively. The loop filters are continuous-time low-pass and bandpass implementations of order 6 and 10, and were fabricated in an InP heterojunction bipolar (HBT) technology. A typical tenth-order design consumes 6 W of power and occupies a die area of 23.5 mm/sup 2/.     

Influence of device engineering on the analog and RF performances of SOI MOSFETs

This work presents a systematic comparative study of the influence of various process options on the analog and RF properties of fully depleted (FD) silicon-on-insulator (SOI), partially depleted (PD) SOI, and bulk MOSFET's with gate lengths down to 0.08 /spl mu/m. We introduce the transconductance-over-drain current ratio and Early voltage as key figures of merits for the analog MOS performance and the gain and the transition and maximum frequencies for RF performances and link them to device engineering. Specifically, we investigate the effects of HALO implantation in FD, PD, and bulk devices, of film thickness in FD, of substrate doping in SOI, and of nonstandard channel engineering (i.e., asymmetric Graded-channel MOSFETs and gate-body contacted DTMOS).     

Static energy reduction techniques for microprocessor caches

Microprocessor performance has been improved by increasing the capacity of on-chip caches. However, the performance gain comes at the price of static energy consumption due to subthreshold leakage current in cache memory arrays. This paper compares three techniques for reducing static energy consumption in on-chip level-1 and level-2 caches. One technique employs low-leakage transistors in the memory cell. Another technique, power supply switching, can be used to turn off memory cells and discard their contents. A third alternative is dynamic threshold modulation, which places memory cells in a standby state that preserves cell contents. In our experiments, we explore the energy and performance tradeoffs of these techniques. We also investigate the sensitivity of microprocessor performance and energy consumption to additional cache latency caused by leakage-reduction techniques.     

High-performance MIM capacitor using ALD high-k HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectrics

For the first time, we successfully fabricated and demonstrated high performance metal-insulator-metal (MIM) capacitors with HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectric using atomic layer deposition (ALD) technique. Our data indicates that the laminate MIM capacitor can provide high capacitance density of 12.8 fF//spl mu/m/sup 2/ from 10 kHz up to 20 GHz, very low leakage current of 3.2 /spl times/ 10/sup -8/ A/cm/sup 2/ at 3.3 V, small linear voltage coefficient of capacitance of 240 ppm/V together with quadratic one of 1830 ppm/V/sup 2/, temperature coefficient of capacitance of 182 ppm//spl deg/C, and high breakdown field of /spl sim/6 MV/cm as well as promising reliability. As a result, the HfO/sub 2/-Al/sub 2/O/sub 3/ laminate is a very promising candidate for next generation MIM capacitor for radio frequency and mixed signal integrated circuit applications.     

Near-ML multiuser detection with linear filters and reliability-based processing

The prohibitive - exponential in the number of users - computational complexity of the maximum-likelihood multiuser detector for direct-sequence code-division multiple-access communications has fueled an extensive research effort for the development of low-complexity multiuser detection alternatives. We show that we can efficiently and effectively approach the error rate performance of the optimum multiuser detector as follows. We utilize a multiuser zero-forcing or minimum mean-square error (MMSE) linear filter as a preprocessor and we establish that the output magnitudes, when properly scaled, provide a reliability measure for each user bit decision. Then, we prepare an ordered, reliability-based error search sequence of length linear in the number of users; it returns the most likely user bit vector among all visited options. Numerical and simulation studies for moderately loaded systems that permit exact implementation of the optimum detector indicate that the error rate performance of the optimum and the proposed detector are nearly indistinguishable over the whole predetection. signal-to-noise ratio range of practical interest. Similar studies for higher user loads (that prohibit comparisons with the optimum detector) demonstrate error rate performance gains of orders of magnitude in comparison with straight decorrelating or MMSE multiuser detection.     

The influence of oxygen partial pressure on growth of the (Hg,Re)-1223 intergrain junction

Hg/sub 0.82/Re/sub 0.18/Ba/sub 2/Ca/sub 2/Cu/sub 3/O/sub 8+/spl delta// polycrystalline samples were successfully obtained by using different oxygen partial pressure in the annealing treatment of the precursor ceramic. The doping state was confirmed by X-ray powder diffraction pattern analysis and by observing distinct thermopower values at room temperature. Also, the intergrain regions have shown an improvement in the critical current density when using the precursor preparation with 10% O/sub 2/ and 90% Ar (optimal doped). The optimal doped sample has presented the highest /spl alpha/ exponent of the J/sub c//spl prop/[1-(T/T/sub c/)/sup 2/]/sup /spl alpha// dependence. For the case of (Hg,Re)-1223 polycrystalline superconductor applications, the /spl alpha/ exponent can be used as a junction quality parameter.     

Mobile Device Security Using Transient Authentication

Mobile devices are vulnerable to theft and loss due to their small size and the characteristics of their common usage environment. Since they allow users to work while away from their desk, they are most useful in public locations and while traveling. Unfortunately, this is also where they are most at risk. Existing schemes for securing data either do not protect the device after it is stolen or require bothersome reauthentication. Transient Authentication lifts the burden of authentication from the user by use of a wearable token that constantly attests to the user's presence. When the user departs, the token and device lose contact and the device secures itself. We show how to leverage this authentication framework to secure all the memory and storage locations on a device into which secrets may creep. Our evaluation shows this is done without inconveniencing the user, while imposing a minimal performance overhead     

Java technology comes to real-time applications

The Java language provides many benefits to application developers, including memory access safety, platform portability, and very high levels of productivity. However, some of the very Java language features that bring these benefits, such as the garbage collector, have also made it difficult or impossible to create applications with bounded response time characteristics. Implementations of the real-time specification for Java (RTSJ) are now available that have proven to be capable of supporting all aspects of real-time systems. This paper discusses the principal concepts underlying the RTSJ, use of the RTSJ's features in real-time applications, the most critical considerations that must be addressed by RTSJ-compliant Java virtual machine implementers, and two example RTSJ-compliant application designs that can fully utilize the RTSJ to portably support their performance requirements.     

InGaN microring light-emitting diodes

The fabrication and performance of an InGaN light-emitting diode (LED) array based on a microring device geometry is reported. This design has been adopted in order to increase the surface area for light extraction and to minimize losses due to internal reflections and reabsorption. Electrical characteristics of these devices are similar to those of a conventional large-area LED, while the directed light extraction proves to be superior. In fact, these devices are found to be more efficient when operated at higher currents. This may be attributed to improved heat sinking due to the large surface area to volume ratio. The potential applications of these devices are also discussed.