Relationship between the dynamic softening transition and wet sliding friction of elastomer compounds

For properly chosen elastomer compounds, thermorheological characterization is combined with an examination of the variation of the wet sliding friction with temperature. A conceptual argument leads to the assumption that the wet sliding friction should maximize at the energy dissipation peak associated with the dynamic softening transition at a characteristic frequency determined by the sliding speed and the effective smallest surface asperity scale. The dynamic softening transition is characterized with the peak in tan δ/G′ⁿ, where tan δ is the loss tangent, G′ is the elastic modulus, and n is a constant between 0 and 1. The William–Landel–Ferry transform is uncritically applied for extrapolating the position of the peak in tan δ/G′ⁿ at high frequencies. Even based on the criterion of tan δ, the results obtained on a concrete surface indicate that the effective smallest asperity scale is of order of 100 μm. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2467–2478, 2004     

Differential scanning calorimetry and thermogravimetric analysis investigation of the thermal properties and degradation of some radiation‐grafted films and membranes

The influence of irradiation and grafting on the crystallinity of three base polymers has been investigated with differential scanning calorimetry. Grafting has the largest effect on the base polymer crystallinity and results in a reduction of the crystallinity. The thermal degradation of the base polymers and grafted films has been investigated with thermogravimetric analysis. The extent of the fluorination of the base polymer, the irradiation method, and the graft level all influence the thermal degradation and its activation energy. It is proposed that the variation of the chain lengths of the grafted polystyrene chains is actually a primary underlying factor responsible for the influence of these various parameters on the degradation process. The first results of a comparative thermal analysis of some fuel‐cell membranes are also presented, and the promise and shortcomings of this method are discussed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2612–2624, 2004     

Nowhere zero 4‐flow in regular matroids

Jensen and Toft 8 conjectured that every 2‐edge‐connected graph without a K₅‐minor has a nowhere zero 4‐flow. Walton and Welsh 19 proved that if a coloopless regular matroid M does not have a minor in {M(K_3,3), M*(K₅)}, then M admits a nowhere zero 4‐flow. In this note, we prove that if a coloopless regular matroid M does not have a minor in {M(K₅), M*(K₅)}, then M admits a nowhere zero 4‐flow. Our result implies the Jensen and Toft conjecture. © 2005 Wiley Periodicals, Inc. J Graph Theory     

Synthesis of 2,7‐Carbazolenevinylene‐Based Copolymers and Characterization of Their Photovoltaic Properties

New electroactive and photoactive conjugated copolymers consisting of alternating 2,7‐carbazole and oligothiophene moieties linked by vinylene groups have been developed. Different oligothiophene units have been introduced to study the relationship between the polymer structure and the electronic properties. The resulting copolymers are characterized by UV‐vis spectroscopy, size‐exclusion chromatography, and thermal and electrochemical analyses. Bulk heterojunction photovoltaic cells from different copolymers and a soluble fullerene derivative, [6,6]‐phenyl‐C₆₁ butyric acid methyl ester, have been fabricated, and promising preliminary results are obtained. For instance, non‐optimized devices using poly(N‐(4‐octyloxyphenyl)‐2,7‐carbazolenevinylene‐alt‐3″,4″‐dihexyl‐2,2′;5′,2″;5″,2″′;5″′,2″″‐quinquethiophenevinylene 1″,1″‐dioxide) as an absorbing and hole‐carrier semiconductor exhibit power conversion efficiency up to 0.8 % under air mass (AM) 1.5 illumination. These features make 2,7‐carbazolenevinylene‐based and related polymers attractive candidates for solar‐cell applications.     

Efficient synthesis of an aldehyde‐capped polythiophene containing fluorinated electron‐withdrawing groups

To incorporate an acceptor type polythiophene segment onto a supramolecular block copolymer for potential light harvesting applications, effective synthetic routes for the end‐functionalized and acceptor‐substituted polythiophenes are critical. The Ullmann coupling reaction can be utilized to obtain electron‐deficient polythiophenes and to attach terminal thiophene units that carry functional groups. In this article, the reactions involving a 2,5‐dibromothiophene monomer containing an electron‐withdrawing fluorinated ester and 5‐bromo‐2‐thiophenecarboxaldehyde (the end‐capper) were studied in detail. It was found that the Ullmann coupling reaction of the dibromide is very fast (completed in a few minutes) and the terminal bromine group does not survive long under the reaction condition. These findings lead to the development of an effective procedure for aldehyde end‐capping of electron‐deficient polythiophenes. Polymers with molecular weights around 4000 Da are routinely obtained. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 41–47, 2007     

Stability control of the electrooptic effect with new maleimide copolymers containing photoreactive tricyanopyrrolidene‐based chromophores

New photocrosslinkable maleimide copolymers have been synthesized by the attachment of a tricyanopyrrolidene‐based chromophore. The 2‐(3‐cyano‐4‐(2‐{4‐[hexyl‐(6‐hydroxy‐hexyl)‐amino]‐phenyl}‐vinyl)‐5‐oxo‐1‐{4‐[4‐(3‐oxo‐3‐phenyl‐propenyl)‐ phenoxy]‐butyl}‐1,5‐dihydro‐pyrrol‐2‐ylidene)‐malononitrile chromophore exhibits nonlinear optical activity and contains a chalcone moiety that is sensitive to UV light (λ = 330–360 nm) for crosslink formation. The maleimide monomers have also been functionalized with chalcone moieties. The resultant copolymers exhibit great processability, and one of them shows a maximum electrooptic coefficient of 90 pm/V at 1300 nm. We could control the thermal stability of the electrooptic coefficient with the newly synthesized photoreactive copolymers successfully. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 531–542, 2007     

Degradative chain transfer in vinyl acetate polymerizations using toluene as solvent

In this work, we propose that retardation in vinyl acetate polymerization rate in the presence of toluene is due to degradative chain transfer. The transfer constant to toluene (C_trs) determined using the Mayo method is equal to 3.8 × 10^?3, which is remarkably similar to the value calculated from the rate data, assuming degradative chain transfer (2.7 × 10^?3). Simulations, including chain‐length‐dependent termination, were carried out to compare our degradative chain transfer model with experimental results. The conversion–time profiles showed excellent agreement between experiment and simulation. Good agreement was found for the M_n data as a function of conversion. The experimental and simulation data strongly support the postulate that degradative chain transfer is the dominant kinetic mechanism. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3620–3625, 2007     

Glass transitions and mixed phases in block SBS

Differential scanning calorimetry (DSC) does not allow for easy determination of the glass‐transition temperature (T_g) of the polystyrene (PS) block in styrene–butadiene–styrene (SBS) block copolymers. Modulated DSC (MDSC), which deconvolutes the standard DSC signal into reversing and nonreversing signals, was used to determine the (T_g) of both the polybutadiene (PB) and PS blocks in SBS. The T_g of the PB block was sharp, at ?92 °C, but that for the PS blocks was extremely broad, from ?60 to 125 °C with a maximum at 68 °C because of blending with PB. PS blocks were found only to exist in a mixed PS–PB phase. This concurred with the results from dynamic mechanical analysis. Annealing did not allow for a segregation of the PS blocks into a pure phase, but allowed for the segregation of the mixed phase into two mixed phases, one that was PB‐rich and the other that was PS‐rich. It is concluded that three phases coexist in SBS: PB, PB‐rich, and PS‐rich phases. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 276–279, 2005     

Isothermal crystallization kinetics of poly(3‐hydroxybutyrate)/layered double hydroxide nanocomposites

Poly(3‐hydroxybutyrate) (PHB)/layered double hydroxides (LDHs) nanocomposites were prepared by mixing PHB and poly(ethylene glycol) phosphonates (PEOPAs)‐modified LDH (PMLDH) in chloroform solution. Both X‐ray diffraction data and TEM micrographs of PHB/PMLDH nanocomposites indicate that the PMLDHs are randomly dispersed and exfoliated into the PHB matrix. In this study, the effect of PMLDH on the isothermal crystallization behavior of PHB was investigated using a differential scanning calorimeter (DSC) and polarized optical microscopy. Isothermal crystallization results of PHB/PMLDH nanocomposites show that the addition of 2 wt % PMLDH into PHB induced more heterogeneous nucleation in the crystallization significantly increasing the crystallization rate and reducing their activation energy. By adding more PMLDH into the PHB probably causes more steric hindrance of the diffusion of PHB, reducing the transportation ability of polymer chains during crystallization, thus increasing the activation energy. The correlation among crystallization kinetics, melting behavior and crystalline structure of PHB/PMLDH nanocomposites can also be discussed. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3337–3347, 2006     

Studies on calcium‐containing poly(urethane ether)s

The calcium salt of mono(hydroxyethoxyethyl)phthalate [Ca(HEEP)₂] was synthesized by the reaction of diethylene glycol, phthalic anhydride, and calcium acetate. Calcium‐containing poly(urethane ether)s (PUEs) were synthesized by the reaction of hexamethylene diisocyanate (HMDI) or tolylene 2,4‐diisocyanate (TDI) with a mixture of Ca(HEEP)₂ and poly(ethylene glycol) (PEG₃₀₀ or PEG₄₀₀) with di‐n‐butyltin dilaurate as a catalyst. A series of calcium‐containing PUEs of different compositions were synthesized with Ca(HEEP)₂/PEG₃₀₀ (or PEG₄₀₀)/diisocyanate (HMDI or TDI) molar ratios of 2:2:4, 3:1:4, and 1:3:4 so that the coating properties of the PUEs could be studied. Blank PUEs without calcium‐containing ionic diols were also prepared by the reaction of PEG₃₀₀ or PEG₄₀₀ with HMDI or TDI. The PUEs were well characterized by Fourier transform infrared, ¹H and ¹³C NMR, solid‐state cross‐polarity/magic‐angle‐spinning ¹³C NMR, viscosity, solubility, and X‐ray diffraction studies. The thermal properties of the polymers were also studied with thermogravimetric analysis and differential scanning calorimetry. The PUEs were applied as top coats on acrylic‐coated leather, and their physicomechanical properties were also studied. The coating properties of PUEs, such as the tensile strength, elongation at break, tear strength, water vapor permeability, flexing endurance, cold crack resistance, abrasion resistance, color fastness, and adhesive strength, were better than the standard values. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2865–2878, 2003