玻璃陶瓷材料中Tm3+离子红外到蓝色上转换发光

系统研究了PbF2+GeO2+WO3ⅩⅣTmF3玻璃陶瓷材料中,在近红外光(1.06μm)激发下,Tm3+离子的发光特性.实验中观测到Tm3+离子的两组峰值位置分别在20920cm-1和22173cm-1的蓝色上转换发光,并证实这两组上转换发光分别与吸收三个和四个光子有关,同时建立了上转换发光的模型.为了选择最佳掺杂浓度,详细地测量了Tm3+离子峰值为20920cm-1的蓝色上转换发光强度与TmF3浓度的关系.     

非线性光纤方向耦合器孤子动力特性分析

利用变分方法,导出了双曲正割型光孤子在非线性光纤耦合器中传输时满足的动力学方程组,分析了该方程组的平衡点性态,讨论了光孤子的开关特性.指出参数|β|<2π.是能实现完全的开关操作的必要条件.     

溶胶-凝胶制备技术与新型催化材料Ⅲ.溶胶粒子表面修饰方法制备催化膜

提出用溶胶粒子表面修饰方法，结合溶胶凝胶技术制备无机催化膜．该方法的基本原理是利用合适的金属配合物在胶粒表面的吸附作用，经溶胶凝胶过程，将活性组分结合到无机膜中．实验测定结果表明：（ＮｉＥＤＴＡ）２－，ＶＯ－３，ＭｏＯ２－４，（Ｐｄ（ＮＨ３）４）２＋，ＰｄＣｌ２－４，ＰｔＣｌ２－６和ＲｈＣｌ３－６可用来修饰ＡｌＯＯＨ溶胶．以Ｐｄ／γＡｌ２Ｏ３催化膜的制备为例，经三次溶胶凝胶过程，可制得无裂缺的厚度为９μｍ的Ｐｄ／γＡｌ２Ｏ３催化膜，膜材料的平均孔直径为６ｎｍ，Ｐｄ被均匀地分布在膜的顶层，其平均粒径为２３ｎｍ．     

一种多晶硅高温压力传感器

制作压力传感器时，在二氧化硅层上淀积多晶硅膜，既可利用优良的机械特性，又可保证压敏电阻与衬底间具有良好的绝缘性，由此可大大提高器件的温度特性。介绍了一种多晶硅压力传感器的原理和设计。实验结果表明，这类传感器具有灵敏度好，精度高等特点，电路工作范围为０－２５０℃，且具有良好的温度稳定性。     

因素空间理论与知识表示的数学框架（Ⅷ）─—变权综合原理

本文是文［１－７］的继续，研究变权综合问题，从确定变权的经验公式入手引出了变权原理，给出了变权的公理化定义，讨论了与之有关的均衡函数及其梯度向量。     

不等波纹函数低通原型的理论及应用

本文提出不等波纹函数低通原型，并对其理论进行初步探讨。切比雪夫函数及最平坦型巴特活兹函数皆为其特例。文中给出不等波纹函数的几个性质，最后给出两个应用实例，消除耦合环自感部分的影响；抑制高次模的微带圆盘腔带通滤波器。     

用于提高国产氩离子激光器相干长度的相干扩展器

本文报导了最近研制成功的用于提高国产氩离子激光器相干长度的相干扩展器。利用这种基于F-P理论的相干扩展器可以使国产氩离子激光器的相干长度由不足5cm一下提高到m的量级,功率损耗在25%～40%之间,有着很好的应用前景。     

An investigation of the Al2O3-CdSe interface in accumulation

The Al₂O₃−CdSe interface of a thin-film transistor is investigated in the frequency range 30 Hz-30 kHz under weak depletion and accumulation. The surface states are, most likely, located in the insulator Al₂O₃ with a concentration varying from 4·10¹⁸ to 10¹⁹ cm⁻³ eV⁻¹. The surface states have a negligible influence on the thin-film transistor operation.     

All retraction operators on a complete lattice form a complete lattice

H. Crapo raised in 1982 the following problem: IfP is a complete lattice, is Retr (P) a complete lattice? here Retr (P) denotes the set of all retraction operators onP with the pointwise order, that is,f≤g in Retr (P) ifff(x)≤g(x) for everyx inP. An affirmative answer will be given in the present paper.     

An approach combining the Ritz-Galerkin and finite difference methods

The nonconforming combination of Ritz-Galerkin and finite difference methods is presented for solving elliptic boundary value problems with singularities. The Ritz-Galerkin method is used in the subdomains including singularities, the finite difference method is used in the rest of the solution domain. Moreover, on the common boundary of two regions where two different methods are used, the continuity conditions are constrained only on the nodes of difference grids. Theoretical analysis and numerical experiments have shown that average errors of numerical solutions and their generalized derivatives can reach the convergence rate O(h^2-δ), where h is the mesh spacing of uniform difference grids, and δ is an arbitrarily small, positive number. This convergence rate is better than O(h), obtained by the nonconforming combination of the Ritz-Galerkin and finite element methods.