Wavelength-scanning Talbot effect and its application for arbitrary three-dimensional step-height measurement

We demonstrate the phenomenon of Talbot self-image plane shift by tuning the wavelength of the broadband light source. A superluminescent diode (SLD) is used as a broad-band light source and an acousto-optic tunable filter (AOTF) as wavelength-scanning device. A periodic grating is illuminated by the wavelength tuned light of SLD using AOTF and Talbot self-image plane is shifted continuously in the longitudinal direction without mechanically moving the grating. The wavelength-scanning Talbot effect is then implemented for the measurement of arbitrary step-height of discontinuous objects with extended range. The main advantages of the proposed system are non-mechanical scanning, high stability because of it’s common-path geometry and compactness. Since the measurement of the phase is not required the system is free from phase ambiguity problem and therefore, the range of measurement is large as compare to interferometric techniques.     

A rapid and sensitive extractive spectrophotometric determination of copper(II) in pharmaceutical and environmental samples using benzildithiosemicarbazone.

Benzildithiosemicarbazone (BDTSC) is proposed as a sensitive and selective analytical reagent for the extractive spectrophotometric determination of copper(II). BDTSC reacts with copper(II) in the pH range 1.0-7.0 to form a yellowish complex. Beer's law is obeyed in the concentration range 0.5-0.4 microg cm(-3). The yellowish Cu(II)-BDTSC complex in chloroform shows a maximum absorbance at 380 nm, with molar absorptivity and Sandell's sensitivity values of 1.63 x 10(4) dm3 mol(-1) cm(-1) and 0.00389 microg cm(-2), respectively. A repetition of the method is checked by finding the relative standard deviation (RSD) (n = 10), which is 0.6%. The composition of the Cu(II)-BDTSC complex is established as 1:1 by slope analysis, molar ratio and Asmus' methods. An excellent linearity with a correlation coefficient value of 0.98 is obtained for the Cu(II)-BDTSC complex. The instability constant of the complex calculated from Edmond and Birnbaum's method is 7.70 x 10(-4) and that of Asmus' method is 7.66 x 10(-4), at room temperature. The method is successfully employed for the determination copper(II) in pharmaceutical and environmental samples. The reliability of the method is assured by analyzing the standard alloys (BCS 5g, 10g, 19e, 78, 32a, 207 and 179) and by inter-comparison of experimental values, using an atomic absorption spectrometer.     

Diastereoselective formation of 2-aryl-3-arenesulfonyl 4-ethyl-1,3-oxazolidines: An X-ray crystallographic and H NMR study

N-Arylsulfonamides of (R)- and (S)-2-amino-1-butanol, on condensation with aromatic aldehydes produced diastereomerically pure 2-aryl-3-arenesulfonyl 4-ethyl-1,3-oxazolidines. The absolute configurations of one enantiomeric pair have been determined from two fully refined X-ray structures, supplemented by nmr data.     

Plasma immersion ion implantation for SOI synthesis: SIMOX and ion-cut

We have demonstrated feasibility to form silicon-on-insulator (SOI) substrates using plasma immersion ion implantation (PIII) for both separation by implantation of oxygen and ion-cut. This high throughput technique can substantially lower the high cost of SOI substrates due to the simpler implanter design as well as ease of maintenance. For separation by plasma implantation of oxygen wafers, secondary ion mass spectrometry analysis and cross-sectional transmission electron micrographs show continuous buried oxide formation under a single-crystal silicon overlayer with sharp Si/SiO₂ interfaces after oxygen plasma implantation and high-temperature (1300°C) annealing. Ion-cut SOI wafer fabrication technique is implemented for the first time using PIII. The hydrogen plasma can be optimized so that only one ion species is dominant in concentration and there are minimal effects by other residual ions on the ion-cut process. The physical mechanism of hydrogen induced silicon surface layer cleavage has been investigated. An ideal gas law model of the microcavity internal pressure combined with a two-dimensional finite element fracture mechanics model is used to approximate the fracture driving force which is sufficient to overcome the silicon fracture resistance.     

Quantitative dependence of MR signal intensity on tissue concentration of Gd(HP-DO3A) in the nephrectomized rat.

Cardiac-gated SE 20/224 +/- 20 MR images were obtained from nephrectomized rats before and after intravenously administering 153Gd-Gd(HP-DO3A). The concentration of Gd, [Gd], was linear in dose in myocardium, skeletal muscle, and blood. Under steady-state conditions, where d[Gd]/dt = 0, image intensities (IIN) in regions of interest were compared with the measured [Gd]. IIN was linear in myocardium at less than or equal to 0.61 mumol/g-myocardium (less than or equal to 0.5 mmol/kg dose) and in skeletal muscle at less than or equal to 0.63 mumol/g-muscle (less than or equal to 0.75 mmol/kg). Above 0.6 mumol Gd/g-tissue, IIN did not increase further. The in vivo data were consistent with measured ex vivo and in vivo relaxivities. A 29% greater slope for IIN versus [Gd] in myocardium [14,439 +/- 4350 IIN (mumol/g)] than in muscle [10,258 +/- 5,296 IIN/(mumol/g)] was attributed to a significant difference in blood content: 25% versus 2% weight blood in myocardium and skeletal muscle, respectively. Two components were apparent from plots of ex vivo 1/T1 versus [Gd] in myocardium and muscle, and only one for blood.     

Design and operation characteristics of a high power transverse flow pulser sustained cw CO2 laser

A transverse flow, transverse discharge cw CO₂ laser in which de discharge is sustained by employing high repetition rate high voltage pulses has been developed. Pulser sustained discharge through electrodes of innovative design provided uniform excitation at electrical input power densities more than 10 W/cc. Laser output power more than 2.5 kW was obtained in a laser gas mixture consisting of 0.5 mbar of CO₂, 16 mbar of N₂ and 38.5 mbar of He. Design details and operational characteristics of this laser are presented.     

Conductivity and dielectric properties of sol–gel derived porous zirconia

The 8-mol percentage Y₂O₃-stabilized Porous Zirconia was prepared using sol–gel method. Zirconium oxalate gel was prepared by the addition of appropriate amount of oxalic acid solution into the 1 M aqueous solution of zirconium-oxy chloride. A cubic phase zirconia powder was obtained by calcination and milling of the zirconium oxalate gel. Crystallization temperature was found about 450 °C from the Differential thermal analysis. The phase analysis by X-ray diffraction shows the presence of cubic phase. Pellets sintered at 1,350 °C were highly porous, and the electrical conductivity was found with lower value due to the porosity, and the hardness was about 8.0 GPa. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, Dec. 7–9, 2006.     

“Optimization of aircraft maintenance/support infrastructure using genetic algorithms—level of repair analysis”

Level of repair analysis (LORA) is an approach used during the design stage of complex equipment for analysis of the cost effectiveness of competing maintenance strategies. LORA is carried as a part of the life cycle cost and cost of ownership analysis and plays a significant role in minimizing the life cycle cost and cost of ownership of the capital equipment. Since many purchasing decisions of complex equipment are based on cost of ownership, it has become essential to carry out LORA to compete in the market. In this paper, we develop a mathematical model for LORA and propose a solution methodology based on genetic algorithms. The concept is illustrated using a hypothetical aircraft engine.