Piezoresistive Behavior Study on Finger‐Sensing Silicone Rubber/Graphite Nanosheet Nanocomposites

A novel finger‐sensing nanocomposite with remarkable and reversible piezoresistivity is successfully fabricated by dispersing homogeneously conductive graphite nanosheets (GNs) in a silicone rubber (SR) matrix. Because of the high aspect ratio of the graphite nanosheets, the nanocomposite displays a very low percolation threshold. The SR/GN nanocomposite with a volume fraction of conductive nanosheets closest to that for the percolation threshold presents a sharp positive‐pressure coefficient effect of the resistivity under very low pressure, namely, in the finger‐pressure range (0.3–0.7 MPa), whereby the abrupt transition could be attributed to compressive‐stress‐induced deformation of the conducting network. The super‐sensitive piezoresistive behavior of the nanocomposite is accounted for by an extension of the tunneling conduction theory which provides a good approximation to the piezoresistive effect.     

Enhancing echo cancellation via estimation of delay

The advent of packetized audio transmission, such as voice over IP (VoIP), has resulted in challenging requirements for echo cancellation technology. One key aspect of this technology is the need to characterize, quickly and accurately, the echo paths in the transmission media. Echo paths consist of a constant time delay with no echo signal and active regions in which the echo signal is present. When an adaptive filter echo cancellation algorithm is used, its performance can be greatly increased, and its complexity can be reduced if it is only applied to the active regions. This requires an algorithm to estimate the constant delay and locate the active regions. Traditionally, delay estimation has been based on direct application of cross-correlation. This method has poor performance because the input signals are highly correlated and has a high implementation cost because many cross-correlation lags have to be computed for longer time delays. The delay estimation addressed in this paper has two major advantages over the traditional methods. The first is that it has improved performance because the input signals are processed to have less correlation. The second is that the implementation cost is significantly reduced because fewer cross-correlation lags are computed, and an efficient method to estimate lags is created.     

Reciprocating sliding wear behavior of laser-clad small amplitude Mo2Ni3Si/NiSi metal silicide composite coatings

Mo₂Ni₃Si/NiSi metal silicide composite coatings with a fine microstructure consisting of Mo₂Ni₃Si primary dendrites and the interdendritic Mo₂Ni₃Si/NiSi eutectics were fabricated on austenitic stainless steel AISI 321 by laser cladding process. Small amplitude reciprocating sliding wear resistance of the coatings is evaluated as functions of normal load and slip amplitude and the wear mechanisms were discussed based on worn surface morphology observations. Results showed that the Mo₂Ni₃Si/NiSi coatings have excellent small amplitude reciprocating sliding wear resistance.     

Hybrid Electrodes Used in Polymer Electro-Optic Modulator with Ultra-Broadband

Hybrid electrode combined coplanar waveguide (CPW) and microstrip lines in ultra-broadband electro-optic modulators. The characteristics of the modulators with hybrid electrode is like that of the modulator with the microstrip lines, in which the microstrip electrode is loaded above only one arm of Mach-Zehnder (M-Z) optical waveguide, besides the problem of microstrip line to coaxial transition and corona polarization in polymer modulators have been best solved at the same time. By using finite element method (FEM), the characteristic parameters such as half-wave voltage, modulation bandwidth characteristic impedance, effective microwave refractive index of polymer modulators with microstrip line and hybrid electrode are analysed and compared in this paper. The results present that velocity match, impendence match and lower microwave propagating loss is easily realized in modulators with hybrid electrode.     

Evidences of phase separation in moisture‐cured poly(urethane urea)s by means of temperature modulated differential scanning calorimetry

The degree of phase separation in several moisture‐cured poly(urethane urea)s (PUUs) was studied by FTIR spectroscopy, wide angle X‐ray diffraction (WAXD), and temperature‐modulated differential scanning calorimetry (TMDSC). This latter technique was shown to be particularly useful in analysing the degree of phase separation in PUU polymers. Both phase mixing and phase segregation coexisted in the PUUs and the degree of phase separation increased as the urea hard segment (HS) content in the PUU increased. The maximum solubility of urea HSs into the polyol soft segments (SSs) was achieved for 50 wt % urea HS content in diol‐based PUUs, whereas for triol‐based PUUs the highest solubility between HS and SS was reached for lower urea HS amount. Finally, the higher the urea HS content the higher the extent of phase separation in the PUU. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 3034–3045, 2007     

Global Asymptotical Synchronization of Chaotic Lur'e Systems Using Sampled Data: A Linear Matrix Inequality Approach

Sampled-data feedback control for master-slave synchronization schemes that consist of identical chaotic Lur'e systems is studied. Sufficient conditions for global asymptotic synchronization of such chaotic Lur'e systems are obtained using the free-weighting matrix approach and expressed in terms of linear matrix inequalities (LMIs). With the help of the LMI solvers, the sampled-data feedback control law can easily be obtained to globally asymptotically synchronize Lur'e chaotic systems. The effectiveness of the proposed method is finally illustrated via numerical simulations of chaotic Chua's circuits.     

Tri-Gate Bulk MOSFET Design for CMOS Scaling to the End of the Roadmap

A tri-gate bulk MOSFET design utilizing a low-aspect-ratio channel is proposed to provide an evolutionary pathway for CMOS scaling to the end of the roadmap. 3-D device simulations indicate that this design offers the advantages of a multi-gate FET (reduced variability in performance and improved scalability) together with the advantages of a conventional planar MOSFET (low substrate cost and capability for dynamic threshold-voltage control).     

环境对MgB_2氧化过程中MgO晶须生长形状的影响

用扫描电镜研究了在 Mg B2 氧化过程中环境对 Mg O晶须生长形状的影响。仅有 Mg B2 时 ,在 80 0℃左右空气气氛中 ,可生长出纳米尺寸的 Mg O晶须。若把 Mg B2 添加到氧化铝陶瓷基体中 ,则生长成竹节状晶须。Mg O晶须生长形状的差别可能是由于氧浓度以及位错等因素造成的。     

2,9-disubstituted 1,10-phenanthroline nickel complexes: Syntheses,characterization, and their ethylene oligomerization

Nickel complexes 1–4 ligated with 2,9-disubstituted-1,10-phenanthroline were synthesized and characterized by FT-IR spectra and elemental analysis. The molecular structure of complex 2 was confirmed by X-ray crystal diffraction analysis. Activated with methylaluminoxane (MAO), those complexes showed moderate activities for ethylene oligomerization. Published in Kinetika i Kataliz, 2007, Vol. 48, No. 5, pp. 710–714. This article was submitted by the authors in English.