Gain clamping in two-stage L-band EDFA using a broadband FBG

A gain-clamped long wavelength band erbium-doped fiber amplifier (L-band EDFA) with an improved gain characteristic is demonstrated by simply adding a broadband conventional band (C-band) fiber Bragg grating (FBG) in a two-stage amplifier system. The FBG reflects backward C-band amplified spontaneous emission (ASE) from the second stage back into the system to clamp the gain. The gain is clamped at about 22.4 dB with a gain variation below 0.4 dB for input signal powers of -40 to -15 dBm. Compared with an unclamped amplifier of similar noise figure values, the small signal gain has improved by 2.4 dB due to the FBG which blocks the backward propagating ASE. At wavelengths from 1570 to 1600 nm, gain of the clamped amplifier varies from 19.4 to 26.7 dB. The corresponding noise figure varies by /spl plusmn/0.35 dB around 5 dB, which is not much different compared to that of the unclamped amplifier.     

High gain L-band erbium-doped fiber amplifier with two-stage double-pass configuration

An experiment on gain enhancement in the long wavelength band erbium-doped fiber amplifier (L-band EDFA) is demonstrated using dual forward pumping scheme in double-pass system. Compared to a single-stage single-pass scheme, the small signal gain for 1580 nm signal can be improved by 13.5 dB. However, a noise figure penalty of 2.9 dB was obtained due to the backward C-band ASE from second stage and the already amplified signal from the first pass that extracting energy from the forward C-band ASE. The maximum gain improvement of 13.7 dB was obtained at a signal wavelength of 1588 nm while signal and total pump powers were fixed at -30 dBm and 92 mW, respectively.     

Index for vehicle acoustical comfort inside a passenger car

Sound quality is among the main factors that influence customers’ preference for choosing good automobile products. It all started more than 10 years ago and grows up so fast due to high competition in the automotive industries. A-weighted noise levels and sound power are usually utilised to measure the noise but they are not adequate to characterise the impact sound inside a car. The most popular approach to determine sound quality of a product is to define an annoyance or specific index, which involves both subjective and objective evaluations. Subjective and objective tests should be studied concurrently in order to determine the sound quality inside a passenger car. This approach is used in this paper to evaluate vehicle comfort index according to most frequently used sound quality metrics, namely; Zwicker loudness, sharpness, roughness and fluctuation strength. As a result researchers of different fields of automotive acoustics investigations can use this index according to the type of road (international road roughness) without any need to perform time-consuming jury tests. The metrics are correlated with jury test results that show which of them and how much has affected the acoustical comfort of the vehicle. The relation between road roughness and vehicle acoustical comfort index is another point of interest in this research.     

Synthesis, structural and magnetic properties of the nanocomposite Fe63B23Nd7Y3Nb3Cr1 magnets

The Fe₆₃B₂₃Nd₇Y₃Nb₃Cr₁ nanocomposite magnets in the form of sheets have been prepared by copper mold casting technique. The phase evolution, crystal structure, microstructural and magnetic properties have been investigated in the as-cast and annealed states. The as-cast sheets show magnetically soft behaviors which become magnetically hard by thermal annealing. The optimal annealed microstructure was composed of nanosize soft magnetic α-Fe (19-29 nm) and hard magnetic Nd₂Fe₁₄B (45-55 nm) grains. The best hard magnetic properties such as intrinsic coercivity, _jH_c of 1119 kA/m, remanence, B_r of 0.44 T, magnetic induction to saturation magnetization ratio, M_r/M_s=0.61 and maximum energy product, (BH)_max of 55 kJ/m³ was obtained after annealing at 680 °C for 15 min. The annealing treatment above 680 °C results in non-ideal phase grains growth, which degrade the magnetic properties.     

Microwave Irradiation and Glutamic Acid-Assisted Phytotreatment of Tannery and Surgical Industrial Wastewater by Sorghum

We investigated how different doses of microwave irradiation (MR) affect seed germination in Sorghum, including the level of remediation against textile and surgical wastewater (WW) by modulating biochemical and morpho-physiological mechanisms under glutamic acid (GA) application. The experiment was conducted to determine the impact of foliar-applied GA on Sorghum under wastewater conditions. Plants were treated with or without microwave irradiation (30 s, 2.45 GHz), GA (5 and 10 mM), and wastewater (0, 25, 50, and 100). Growth and photosynthetic pigments were significantly decreased in plants only treated with various concentrations of WW. GA significantly improved the plant growth characteristics both in MR-treated and -untreated plants compared with respective controls. HMs stress increased electrolyte leakage (EL), hydrogen peroxide (H₂O₂), and malondialdehyde (MDA) content; however, the GA chelation significantly improved the antioxidant enzymes activities such as ascorbate oxidase (APX), superoxide dismutase (SOD), peroxidase (POD), and catalase (CAT) both in MR-treated and -untreated plants under WW stress compared with respective controls. The results suggested that the MR-treated plants accumulate higher levels of HMs under GA addition in comparison to the WW-only-treated and MR-untreated plants. The maximum increase in Cd accumulation was observed in the range of 14–629% in the roots, 15–2964% in the stems, and 26–4020% in the leaves; the accumulation of Cu was 18–2757% in the roots, 15–4506% in the stems, and 23–4605% in the leaves; and the accumulation of Pb was 13–4122% in the roots, 21–3588% in the stems, and 21–4990% in the leaves under 10 mM GA and MR-treated plants. These findings confirmed that MR-treated sorghum plants had a higher capacity for HMs uptake under GA and could be used as a potential candidate for wastewater treatment.     

Exogenous Application of Green Titanium Dioxide Nanoparticles (TiO2 NPs) to Improve the Germination,Physiochemical, and Yield Parameters of Wheat Plants under Salinity Stress

Agriculture is the backbone of every developing country. Among various crops, wheat (Triticum aestivum L.) belongs to the family Poaceae and is the most important staple food crop of various countries. Different biotic (viruses, bacteria and fungi) and abiotic stresses (water logging, drought and salinity) adversely affect the qualitative and quantitative attributes of wheat. Among these stresses, salinity stress is a very important limiting factor affecting the morphological, physiological, biochemical attributes and grain yield of wheat. This research work was carried out to evaluate the influence of phytosynthesized TiO₂ NPs on the germination, physiochemical, and yield attributes of wheat varieties in response to salinity. TiO₂ NPs were synthesized using TiO₂ salt and a Buddleja asiatica plant extract as a reducing and capping agent. Various concentrations of TiO₂ nanoparticles (20, 40, 60 and 80 mg/L) and salt solutions (NaCl) (100 and 150 mM) were used. A total of 20 mg/L and 40 mg/L improve germination attributes, osmotic and water potential, carotenoid, total phenolic, and flavonoid content, soluble sugar and proteins, proline and amino acid content, superoxide dismutase activity, and reduce malondialdhehyde (MDA) content at both levels of salinity. These two concentrations also improved the yield attributes of wheat varieties at both salinity levels. The best results were observed at 40 mg/L of TiO₂ NPs at both salinity levels. However, the highest concentrations (60 and 80 mg/L) of TiO₂ NPs showed negative effects on germination, physiochemical and yield characteristics and causes stress in both wheat varieties under control irrigation conditions and salinity stress. Therefore, in conclusion, the findings of this research are that the foliar application of TiO₂ NPs can help to improve tolerance against salinity stress in plants.     

Modeling and Simulation for Transient Thermal Analyses Using a Voltage-in-Current Latency Insertion Method

This article presents a modeling and simulation method for transient thermal analyses of integrated circuits(ICs) using the original and voltage-in-current(VinC) latency insertion method(LIM). LIM-based algorithms are a set of fast transient simulation methods that solve electrical circuits in a leapfrog updating manner without relying on large matrix operations used in conventional Simulation Program with Integrated Circuit Emphasis(SPICE)-based methods which can significantly slow down the sol...     

Fatigue Life of Megawatt-Scale Composite Wind Turbine Blades with Shallow-Angled Laminates

Mechanics of Composite Materials - The fatigue life of megawatt-scale composite wind turbine blades implemented with shallow-angled laminates is investigated. Full dynamic simulations of a 5-MW...     

Photoredox-Mediated Reaction of gem-Diborylalkenes: Reactivity Toward Diverse 1,1-Bisborylalkanes

The use of gem-diborylalkenes as radical-reactive groups is explored for the first time. These reactions provide an efficient and general method for the photochemical conversion of gem-diborylalkenes to rapidly access 1,1-bisborylalkanes. This method exploits a novel photoredox decarboxylative radical addition to gem-diborylalkenes to afford α-gem-diboryl carbon-centered radicals, which benefit from additional stability by virtue of an interaction with the empty p-orbitals on borons. The reaction offers a highly modular and regioselective approach to γ-amino gem-diborylalkanes. Furthermore, EPR spectroscopy and DFT calculations have provided insight into the radical mechanism underlying the photochemistry reaction and the stability of the bis-metalated radicals, respectively.