有机噻吩类衍生物作为电致变色材料*

噻吩类衍生物包括聚噻吩衍生物和齐聚噻吩衍生物。本文从有目的地设计、合成噻吩类衍生物的角度出发,探索了其作为电致变色材料的应用,综述了噻吩类衍生物作为电致变色材料的最新研究进展。     

纳米二氧化硅水溶胶成膜特性研究

研究了纳米SiO2水溶胶的固液二相流成膜特性．结果表明，水溶胶中的Si02固体颗粒的粒径及质量分数对粘度的影响较小，对成膜能力和承载能力的影响较大；在薄膜润滑阶段，固体颗粒的粒径和质量分数对润滑状态的稳定性具有一定的影响，随着速度的增加，液体膜厚度逐渐增大，固体颗粒对液体润滑膜稳定性及性能的影响逐渐减弱；在弹流润滑阶段，固体颗粒的影响很小。     

线型优化最大熵线性预测方法自回归模型三种求解方法的比较

采用三种方法：修正协方差法MCOV(Modified Covariance Method)、递推极大似然估计法RMLE(Recursive Maximum Likelihood Estimator)和伯格法(Burg Method)求解线型优化最大熵线性预测方法中的自回归模型系数,并且在不同求解方法情况下,将阶次、信噪比对光谱复原的影响作了详尽的比较.研究结果表明:在线型优化最大熵线性预测方法的自回归模型系数三种求解方法中,修正协方差法要优于递推极大似然估计法和伯格法.     

Preparation and tribological properties of DLC/Ti filmby pulsed laser arc deposition

This paper reports that DLC (diamond like carbon)/Ti and DLC films were prepared by using pulsed laser arc deposition. R-ray diffraction, Auger electron spectroscopy, Raman spectroscopy, atomic force microscopy, nanoindenter, spectroscopic ellipsometer, surface profiler and micro-tribometer were employed to study the structure and tribological properties of DLC/Ti and DLC films. The results show that DLC/Ti film, with $I(D)/I(G)$ 0.28 and corresponding to 76{\%} sp$^{3}$ content calculated by Raman spectroscopy, uniform chemical composition along depth direction, 98 at{\%} content of carbon, hardness 8.2 GPa and Young's modulus 110.5 GPa, compressive stress 6.579 GPa, thickness 46~nm, coefficient of friction 0.08, and critical load 95mN, exhibits excellent mechanical and tribological properties.     

有机/无机复合功能材料倒脊型波导热光开关

利用溶胶-凝胶技术自主合成了一种具有优良光学特性和高热稳定性的有机/无机复合芯层材料.这种功能材料的分子中含有有机柔性侧链,可形成环氧交联.与无机SiO2-TiO2体系相比,具有较高的热光系数(量级为10-4/K),以及更好的成膜性和可加工性.通过与实验室自行配制的P(MMA-GMA)包层材料相匹配,设计制备了基于这种有机/无机复合功能材料的倒脊型波导马赫-曾德尔型热光开关.器件的波导与热电极性能良好.插入损耗为10dB,驱动功率15mW,开关时间小于1ms,消光比15dB.     

All polymer asymmetric Mach-Zehnder interferometer waveguide sensor by imprinting bonding and laser polishing

We present an all polymer asymmetric Mach–Zehnder interferometer(AMZI) waveguide sensor based on imprinting bonding and laser polishing method. The fabrication methods are compatible with high accuracy waveguide sensing structure. The rectangle waveguide structure of this sensor has three sensing surfaces contacting the test media, and its sensing accuracy can be increased 5 times compared with that of one surface sensing structure. An AMZI device structure is designed. The single mode condition, the length of the sensing arm, and the length deviation between the sensing arm and the reference arm are optimized. The length deviation is optimized to be 19.8 μm in a refractive index range between1.470 and 1.545. We fabricate the AMZI waveguide by lithography and wet etching method. The imprinting bonding and laser polishing method is proposed and investigated. The insertion loss is between-80.36 dB and-10.63 dB. The average and linear sensitivity are 768.1 d B/RIU and 548.95 dB/RIU, respectively. And the average and linear detection resolution of the sensor are 1.30×10~(-6) RIU(RIU: refractive index unit) and 1.82×10~(-5) RIU, respectively. This sensor has a fast and cost-effective fabrication process which can be used in the cases of requiring portability and disposability.     

绕Hydronautics水翼空化云流动的实验研究

采用高速全流场显示技术和DPIV对空化水翼近壁处的空化云流动形态和运动机理进行了讨论.结果表明:绕Hydronautics翼型的空化云运动是一个准周期性过程:稳定空泡团初生在翼型前部,向翼型后部发展布满整个翼面,在翼型后缘出现汽泡团旋涡,伴随反向运动,最终向下游脱落.当前条件下空泡团旋涡脱落周期约为74 ms.空化区与主流区的交界面上存在较大的速度梯度,一组对涡出现在翼型尾部处交界面上.此外,采用以空泡为示踪粒子的DPIV能够对空化流动流速分布进行有效测量.     

The effects of sapphire nitridation on GaN growth by metalorganic chemical vapour deposition

In situ optical reflectivity measurements are employed to monitor the GaN epilayer growth process above a low-temperature GaN buffer layer on a c-plane sapphire substrate by metalorganic chemical vapour deposition. It is found that the lateral growth of the GaN islands and their coalescence are promoted in the initial growth stage if optimized nitridation time and temperature are selected when the substrate is pre-exposed to ammonia. As confirmed by atomic force microscopy observations, the quality of the GaN epilayers is closely dependent on the surface morphology of the nitridated buffer layer, especially grain size and nucleation density.     

两种气液两相流模型的应用和比较

本文应用MUSIG模型[1]和均一直径模型对某溶液堆台架模型堆芯内气液流动传热进行了数值模拟.在MUSIG模型中堆芯内离散相气泡被分为5组不同直径的气泡,用于分析堆芯内气泡的流动变化和大小分布,采用Luo and Svendsen[2]和Prince and Blanch[3]模型描述不同直径气泡组间的破裂和聚合.在均一直径模型中,堆芯内的气体被考虑为同一直径的组分,并且不考虑其破裂与聚合现象.计算得到采用两个模型的模拟结果并且对其进行了对比研究.结果显示应用MUSIG模型的计算结果与台架实验结果吻合更好.     

PSM��ѹ��Դ��������ϵͳ����

介绍了HL-2A装置上用于二级加热系统的PSM高压脉冲电源的反馈控制系统.该电源控制系统以DSP+FPGA作为控制核心,输出112路驱动脉冲,以此来控制112个IGBT的通断,包括了驱动、通信、计算、反馈等部分,使电源系统输出稳定高压.设计了远程通信系统,其中基于VB的上位机与控制系统之间采用CAN总线技术来实现电源系统的相关参数设定及传输.DSP与FPGA实现了计算、反馈等功能.完成了相关的代码编写与系统测试.实验测试结果表明,该控制系统实现了高压电源的稳定输出,满足了实验的需求.