Teleportation of an Arbitrary Multipartite GHZ-Class State by One EPR Pair

We present a scheme for perfectly teleporting an arbitrary and unknown N-particle GHZ-class state from a sender to a receiver. We just need one quantum channel composed of two or three particles in the maximally entangled state. The sender performs one Bell-state measurement on two of her particles and N - 1 Hadamard operations and N - 1 yon Neumann measurements on the rest N - 1 particles. The receiver adopts one corresponding unitary transformation on his particles shared with the sender. After that, the receiver can obtain the original N-particle GHZ-class state by introducing N - 1 ancillary particles and carrying out N - 1 controlled-NOT operations. We also generalize the scheme to the case of controlled teleportation.     

Inner Surface Modification of a Tube by Magnetic Glow-Arc Plasma Source Ion Implantation

A new method named the magnetic glow-arc plasma source ion implantation （MGA-PSⅡ） is proposed for inner surface modification of tubes. In MGA-PSⅡ, under the control of an axial magnetic field, which is generated by an electric coil around the tube sample, glow arc plasma moves spirally into the tube from its two ends. A negative voltage applied on the tube realized its inner surface implantation. Titanium nitride （TIN） films are prepared on the inner surface of a stainless steel tube in diameter 90mm and length 600mm. Hardness tests show that the hardness at the tube centre is up to 20 GPa. XRD, XPS and AES analyses demonstrate that good quality of TiN films can be achieved.     

Photoacoustic characteristics of lipid-rich plaques under ultra-low temperature and formaldehyde treatment

Photoacoustic imaging(PAI) has been used to characterize the spatial and quantitative features of lipid-rich atherosclerotic plaques with high sensitivity and specificity. In this Letter, we first validate that the ultra-low temperature and formaldehyde treatment have no effect on photoacoustic characteristics of the artery samples.Comparative experiments between the PAI and histological results demonstrate that the ultra-low temperature or formaldehyde treatment has few effects on the PAI of the lipid-rich atherosclerotic plaques; the lipid relative concentration and the lipid percentage by PAI hold high correlation with histology.     

Hybrid Deconvolution of Adaptive Optics Retinal Images from Wavefront Sensing

Adaptive optics can be used to compensate for the wave aberration of the human eyes to achieve high-resolution imaging in real time. However the correction ＆ partial due to the limitation of hardware. We propose a kind of hybrid image post-processing method, which uses the blind deconvolution combined with the residual data in wavefront sensor to restore the partially adaptive optics corrected retinal image. This method is applied in the image restoration of the vivid human retinal images. The results show that it is effective to improve the retinal image quality.     

应用PTV技术对颗粒碰撞规律的研究

为了研究稠密气固两相流中颗粒团聚的形成和破碎现象,本文提出了采用可获得颗粒运动学参数的可视化测量技术一PTV技术间接测量颗粒碰撞过程中的作用力的新思路和方法。在建立双球碰撞的运动学参数与动力学参数相互关系的数学模型基础上,设计了微球颗粒的碰撞实验并利用上述模型推演出了颗粒间作用力和碰撞能量损失等参数。     

大气压冷等离子体射流灭活子宫颈癌Hela细胞

研究了大气压冷等离子体射流对子宫颈癌Hela细胞的灭活机制. 在倒置显微镜下观察不同等离子体处理条件下的细胞形态, 并通过中性红吸收测试定量测定各个条件下的细胞存活率. 将功率维持在18 W, 在900 mL/min 氩等离子体中添入氧气的百分含量分别为1%, 2%, 4% 和8%的条件下处理Hela细胞, 探讨活性气体氧气在惰性气体氩气中的百分含量对Hela癌细胞灭活效率的影响, 发现添加2%氧气时, 氩/氧等离子体灭活效果最佳, 处理180 s后细胞存活率可降至7%. 当继续添加氧超过2%时, 灭活效果逐渐减弱, 直至8%时, 其效果反而不如单纯氩等离子体. 通过测量等离子体发射光谱, 结果表明活性氧自由基在癌细胞灭活过程中可能起关键作用. 关键词： 大气压冷等离子体射流 Hela癌细胞 存活率 发射光谱     

非均匀散射层矢量辐射传输(VRT)方程高阶散射解的迭代法

将散射介质层在z轴方向划分成薄层，用薄层的一阶散射强度、Fourier变换和迭代方法求解散射介质整层的矢量辐射传输(VRT)方程的高阶散射解.该方法将一阶散射与高阶散射迭代结合起来，计算公式简明，可计算高阶迭代解，计算时间少.计算结果与一层均匀散射介质的VRT方程一阶Mueller矩阵解、半空间均匀散射介质二阶Mueller矩阵解、以及离散坐标-特征值特征矢量法的VRT热辐射的数值解作了全面的比较.提出并讨论了非均匀散射层主动与被动VRT方程的高阶解.本计算程序可以通用于非球形粒子多层结构及非均匀介质的散射和热辐射计算. 关键词： VRT方程 分层 迭代解     

SHS等离子喷涂制备FeAl2O4-Al2O3-Fe纳米复合涂层的研究

利用SHS等离子喷涂技术,将经过机械团聚法制备的Fe2O3-Al复合粉体送入等离子焰流,沉积出厚度约为400 μm的复合涂层.利用XRD,SEM 和TEM等检测手段对涂层的成分和组织进行了分析,测定了涂层的显微硬度、断裂韧性以及耐磨性.结果表明涂层为具有纳米结构的FeAl2O4-Al2O3-Fe纳米复合组织;涂层的显微硬度为HV100g870;断裂韧性是普通Al2O3涂层的2倍;无润滑磨损的耐磨性是普通Al2O3涂层的2.5倍.     

（Ti,Al）N Film on Normalized T8 Carbon Tool Steel Prepared by Pulsed High Energy Density Plasma Technique

Under optimized operating parameters, a hard and wear resistant （Ti,Al）N film is prepared on a normalized T8 carbon tool steel substrate by using pulsed high energy density plasma technique. Microstructure and composition of the film are analysed by x-ray diffraction, x-ray photoelectron spectroscopy, Auger electron spectroscopy and scanning electron microscopy. Hardness profile and tribological properties of the film are tested with nano- indenter and ring-on-ring wear tester, respectively. The tested results show that the microstructure of the film is dense ahd uniform and is mainly composed of （Ti,Al）N and A1N hard phases. A wide transition interface exists between the film and the normalized T8 carbon tool steel substrate. Thickness of the film is about lO00nm and mean hardness value of the film is about 26 GPa. Under dry sliding wear test conditions, relative wear resistance of the （Ti, Al）N film is approximately 9 times higher than that of the hardened T8 carbon tool steel reference sample. Meanwhile, the （Ti,Al）N film has low and stable friction coefficient compared with the hardened T8 carbon tool steel reference sample.     

Surface modification of polytetrafluoroethylene film using single liquid electrode atmospheric- pressure glow discharge

Polytetrafluoroethylene films are treated by room temperature helium atmospheric pressure plasma plumes, which are generated with a home-made single liquid electrode plasma device. After plasma treatment, the water contact angle of polytetrafluoroethylene film drops from 114°to 46°and the surface free energy increases from 22.0 mJ/m2 to 59.1 mJ/m2. The optical emission spectrum indicates that there are reactive species such as O2+ , O and He in the plasma plume. After plasma treatment, a highly crosslinking structure is formed on the film surface and the oxygen element is incorporated into the film surface in the forms of -C-O-C-, -C=O, and -O-C=O groups. Over a period of 10 days, the contact angle of the treated film is recovered by only about 10 , which indicates that the plasma surface modification is stable with time.