The completely positive and doubly nonnegative completion problems

We prove the following. Let G be an undirected graph. Every partially specified symmetric matrix, the graph of whose specified entries is G and each of whose fully specified submatrices is completely positive (equal to BB^T for some entrywise nonnegative matrix B), may be completed to a completely positive matrix if and only if G is a block-clique graph (a chordal graph in which distinct maximal cliques overlap in at most one vertex). The same result holds for matrices that are doubly nonnegative (entrywise nonnegative and positive semidefinite).     

The effect of buoyancy on the weight gain signal in LEC crystal growth

Crystal diameter monitoring in liquid encapsulated Czochralski (LEC) growth using the weighing method is investigated. An analytical expression for the differential weight gain signal is derived for stationary growth conditions accounting for bouyancy. For the GaAs/B₂O₃ system the buoyancy component of the signal can easily amount to 30%. The formula can be applied to determine the crystal/melt interface area, provided the radius of the part emerging from the encapsulant is known, either in advance as the seed dimension, or by separate monitoring using, e.g., conventional optical methods.     

Improvement of least-squares finite difference method on simulating slider air bearings in head disk systems

Least-squares finite difference (LSFD) method, one of mesh-free methods, is used to solve slider air bearings problem through discritizing the generalized Reynolds equation into nonlinear systems of algebraic equations. Two approximation schemes for the linearization of these equations are presented and compared. And, some new techniques to search supporting points for the reference node in the mesh-free method were proposed and explored. Therefore, these improvements eliminate some potential limitation of the LSFD method previously published and further facilitate its employment in complex slider models. Advanced step slider as an example of negative pressure sliders is simulated and verified using the improved LSFD mesh-free method in head disk systems.     

X-ray evidence for the absence of 90°-domains in polycrystalline PbTiO3 thin films with grains below a critical size

3 thin films is systematically studied by using X-ray diffraction (XRD). The PbTiO₃ thin films with different average grain sizes were prepared on various substrates by a sol-gel process. The films on NaCl and fused glass are randomly grain-oriented, while those on (111)Pt/Ti/SiO₂/Si are highly {100} cubic index grain-oriented . It is found from the XRD patterns of the films on NaCl that with decreasing average grain size from 230 to 80 nm, the intensities of high h index (h>l) peaks (hkl), such as (100), (110), (200), (201), (210), (211), etc., decrease rapidly and ultimately disappear, whereas another set of peaks (lkh), including (001), (002), (102), (112), etc., are still intense. This interesting result suggests that at grain size below a certain critical size an increasing number of grains no longer show 90°-domains, which is confirmed by TEM observations. Meanwhile, X-ray evidence of such a grain-size-related absence of 90°-domains is also found for PbTiO₃ films on Pt(111) and fused-glass substrates. The volume fractions of single-domain grains (without 90°-domains) in the films are estimated from their XRD patterns. By combining SEM and TEM investigations, the critical grain size for the formation of 90°-domains is further determined to be near 200 nm. Received: 19 December 1996/Accepted: 24 March 1997     

AUTOMATED WIND TUNNEL MEASUREMENTS

It is common practice in power transmission to use bundled overhead electrical conductors because the lower rate of corona discharge, compared with single conductors, makes the bundle attractive for high voltages. However, secondary problems may arise from the vibrations induced by the aerodynamic forces which act on the leeward conductors as a result of their immersion in the wake of a windward conductor. Thus, in addition to possible aeolian and galloping oscillations observed for a single conductor, bundle conductors may also be subjected to wake-induced oscillations. ^1,2 Although extensive research has been done on the aeroelastic behavior of single and bundled conductors which are bare, little is known about the galloping or wake oscillation characteristics of given bundle conductors which, depending upon the environmental conditions during the formation of ice, may have five or so representative shaped cross-sections. One important task involves the aerodynamic quasi-static force and moment measurements in a wind tunnel using full scale conductor cross-sections each of which must be rotated through many angles at different spacings. Such measurements are repetitive as well as tediously time consuming and, hence, are beneficially automated. A reliable, accurate and inexpensive automated apparatus is described in this paper which permits the aerodynamic measurements to be performed efficiently and without intervention. Most importantly, it relieves the operator of the usual responsibility for manually controlling the separation and orientation of the sections as well as the need to manually compensate fluctuations in the free stream air speed. For simplicity, the apparatus is detailed in the context of a twin bundle conductor.     

Low-energy ion-assisted control of interfacial structures in metallic multilayers

A molecular dynamics method has been used to simulate the argon ion-assisted deposition of Cu/Co/Cu multilayers and to explore ion beam assistance strategies that can be used during or after the growth of each layer to control interfacial structures. A low-argon ion energy of 5–10 eV was found to minimize a combination of interfacial roughness and interlayer mixing (alloying) during the ion-assisted deposition of multilayers. However, complete flattening with simultaneous ion assistance could not be achieved without some mixing between the layers when a constant ion energy approach was used. It was found that multilayers with lower interfacial roughness and intermixing could be grown either by modulating the ion energy during the growth of each metal layer or by utilizing ion assistance only after the completion of each layers deposition. In these latter approaches, relatively high-energy ions could be used since the interface is buried and less susceptible to intermixing. The interlayer mixing dependence upon the thickness of the over layer has been determined as a function of ion energy.