Synthesis and properties of noncoplanar rigid‐rod aromatic polyhydrazides and poly(1,3,4‐oxadiazole)s containing phenyl or naphthyl substituents

Two new phenyl‐ and naphthyl‐substituted rigid‐rod aromatic dicarboxylic acid monomers, 2,2′‐diphenylbiphenyl‐4,4′‐dicarboxylic acid ( 4 ) and 2,2′‐di(1‐naphthyl)biphenyl‐4,4′‐dicarboxylic acid ( 5 ), were synthesized by the Suzuki coupling reaction of 2,2′‐diiodobiphenyl‐4,4′‐dicarboxylic acid dimethyl ester with benzeneboronic acid and naphthaleneboronic acid, respectively, followed by alkaline hydrolysis of the ester groups. Four new polyhydrazides were prepared from the dicarboxylic acids 4 and 5 with terephthalic dihydrazide (TPH) and isophthalic dihydrazide (IPH), respectively, via the Yamazaki phosphorylation reaction. These polyhydrazides were amorphous and readily soluble in many organic solvents. Differential scanning calorimetry (DSC) indicated that these hydrazide polymers had glass transition temperatures in the range of 187–234 °C and could be thermally cyclodehydrated into the corresponding oxadiazole polymers in the range of 300–400 °C. The resulting poly(1,3,4‐oxadiazole)s exhibited T_g's in the range of 252–283 °C, 10% weight‐loss temperature in excess of 470 °C, and char yield at 800 °C in nitrogen higher than 54%. These organo‐soluble polyhydrazides and poly(1,3,4‐oxadiazole)s exhibited UV–Vis absorption maximum at 262–296 and 264–342 nm in NMP solution, and their photoluminescence spectra showed maximum bands around 414–445 and 404–453 nm, respectively, with quantum yield up to 38%. The electron‐transporting properties were examined by electrochemical methods. Cyclic voltammograms of the poly(1,3,4‐oxadiazole) films cast onto an indium‐tin oxide (ITO)‐coated glass substrate exhibited reversible reduction redox with E_onset at ?1.37 to ?1.57 V versus Ag/AgCl in dry N,N‐dimethylformamide solution. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6466–6483, 2006     

Viscometric study of gelatin in dilute aqueous solutions

The viscosities of aqueous solutions of gelatin at different temperatures were carefully measured in a common glass‐capillary Ubbelohde viscometer at dilute to extremely dilute concentrations. The adsorption effect that occurred in the viscosity measurements was theoretically analyzed and discussed. A theory based on Langmuir isotherms could adequately describe the existing data. Some structural information was obtained by the use of an iterative fitting procedure to treat the reduced viscosity data, which disclosed that individual gelatin chains underwent a coil‐to‐helix transition as the solution cooled from 40 to 15 °C. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1804–1812, 2006     

Sulfonated poly(aryl ether ether ketone ketone)s containing fluorinated moieties as proton exchange membrane materials

A series of sulfonated poly(aryl ether ether ketone ketone)s statistical copolymers with high molecular weights were synthesized via an aromatic nucleophilic substitution polymerization. The sulfonation content (SC), defined as the number of sulfonic acid groups contained in an average repeat unit, could be controlled by the feed ratios of monomers. Flexible and strong membranes in sodium sulfonate form could be prepared by the solution casting method, and readily transformed to their proton forms by treating them in 2 N sulfuric acid. The polymers showed high T_gs, which increased with an increase in SC. Membranes prepared from the present sulfonated poly(ether ether ketone ketone) copolymers containing the hexafluoroisopropylidene moiety (SPEEKK‐6F) and copolymers containing the pendant 3,5‐ditrifluoromethylphenyl moiety (SPEEKK‐6FP) had lower water uptakes and lower swelling ratios in comparison with previously prepared copolymers containing 6F units. All of the polymers possessed proton conductivities higher than 1 × 10^?2 S/cm at room temperature, and proton conductivity values of several polymers were comparable to that of Nafion at high relative humidity. Their thermal stability, oxidative stability, and mechanical properties were also evaluated. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2299–2310, 2006     

合成丙交酯中微量水分分析

合成丙交酯中微量水分分析徐溢，柳胜春（重庆大学化工学院分析教研室６３００４４）关键词丙交酯，微量水，定量分析丙交酯是人工合成骨材料聚乳酸的合成中间体，其性能决定着合成产品的品质，要获得高质量的合成材料，对中间体的分析和监测十分重要。一般要求丙交酯中间...     

三磷酸胞苷在Duolite A-30树脂上的交换过程研究

根据CTP在离子交换树脂上的吸附容量和分离因数的大小,确定Duolite A-30树脂适合CTP与CDP,CMP之间的分离.对CTP在Duolite A-30树脂上的吸附动力学和热力学研究表明,在283.15K~303.15K之间,CTP的质量浓度在7.5g/L以上时,Duolite A-30树脂对CTP的吸附主要受颗粒扩散的控制,其有效扩散系数为D=3.47×10-7cm2/s,溶液的质量浓度≤1.0g/L时,CTP与Duolite A-30树脂之间的交换速率主要受液膜控制,其液膜扩散系数为Kf =4.112×10-4/s.同时测定了不同条件下三磷酸胞苷溶液在Duolite A-30树脂固定床离子交换柱中的穿透曲线,研究了进口浓度、进口流速、原料液温度、原料液的pH值及柱高对穿透曲线的影响.用二阶动力学推动力模型描述固定床动态过程,考察了轴向返混对穿透曲线的影响,并从穿透曲线回归得到总传质系数,模型计算值与实验数据符合良好.     

牛血清白蛋白在NVP/HEMA无规共聚物水凝胶上的吸附研究

合成了不同含水量的N-乙烯吡咯烷酮(NVP)／甲基丙烯酸-β-羟乙酯(HEMA)共聚物水凝胶．研究了温度、pH值，蛋白质初浓度及离子强度等因素对牛血清白蛋白吸附性能的影响．采用紫外分光光度法测定BSA的吸附量．结果表明，蛋白质初浓度越高．温度越高，离子强度越大；蛋白质内部更多的疏水性氧基酸残基暴露于外部．吸附量增加：在等电点pH=4．7附近蛋白质沉积量最大．     

STUDIES ON THE PREPARATION OF ZINC-CONTAINING ACTIVATED CARBON FIBERS AND THEIR ANTIBACTERIAL ACTIVITY

1. INTRODUCTION Microbial pollution will bring about various problems in industry and other vital fields, such as causing decomposing of materials, harming people抯 health. In order to reduce these problems, new antibacterial materials have been demanded. Recently, much attention has been paid to inorganic materials including zinc oxide [1~4]. These inorganic antibacterial materials are now substituting for organic materials to avoid releasing noxious organic molecules harmful to humans;…     

四元缔合物体系薄层树脂相分离与光度法联用测定痕量钴

提出了在酸性条件下 (pH=5.0),利用阳离子交换树脂-丁二酮肟-碘-钴四元体系,通过薄层树脂相光度法测定钴的新方法。本法灵敏度高 (e454=1.7105L/molcm),比水相光度法提高14倍,精密度理想 (测定2.0礸/ml Co(II) 6次,RSD=1.3%),选择性好。实测药品VB12及天然水中钴,线性范围0.024~2.0礸/ml (定容50ml),检出限10.4ng/ml。     

化学键合吸附剂的合成及吸附行为

在无定型硅胶上化学键合十八烷基三氯硅烷，键合率17%-20％，粒度5μm-10μm，以此键合的吸附剂可有效地吸附香烟烟气中的焦油、亚硝胺，吸附率分别为15%-18％和37%-43％，研究了化学键合吸附剂的粒度和加入量对吸附性能的影响。     

离子交换树脂纯化酪蛋白磷酸肽研究

通过单因素实验和正交试验确定了使用D-201型大孔强碱性阴离子交换树脂纯化酪蛋白磷酸肽(CPPs)的操作条件为：洗脱温度40℃、洗脱酸(HCI)浓度0．2mol／L、洗脱速度2．3ml／min、进样浓度2％(w／v)，进一步应用HPSEC技术分析考察了离子交换树脂纯化后含磷洗脱峰分子量分布情况，并计算了产品氮磷比与纯化收率．