具有位相型修理的离散时间可修排队系统

本文研究了具有一般独立输入，位相型修理的离散时间可修排队系统，假定服务台对顾客的服务时间和服务台寿命服从几何分布，运用矩阵解析方法我们给出系统嵌入在到达时刻的稳态队长分布和等待时间分布，并证明这些分布均为离散位相型分布．我们也得到在广义服务时间内服务台发生故障次数的分布，证明它服从一个修正的几何分布．我们对离散时间可修排队与连续时间可修排队进行了比较，说明这两种排队系统在一些性能指标方面的区别之处．最后我们通过一些数值例子说明在这类系统中顾客的到达过程、服务时间和服务台的故障率之间的关系．     

蒙特卡罗计算机模拟应用一例

通过圆周率的计算，说明蒙特卡罗计算机模拟方法的应用过程     

Transport through artificial single-molecule magnets: Spin-pair state sequential tunneling and Kondo effects

The transport properties of an artificial single-molecule magnet based on a CdTe quantum dot doped with a single Mn+2 ion(S=5/2) are investigated by the non-equilibrium Green function method.We consider a minimal model where the Mn-hole exchange coupling is strongly anisotropic so that spin-flip is suppressed and the impurity spin S and a hole spin s entering the quantum dot are coupled into spin pair states with(2S+1) sublevels.In the sequential tunneling regime,the differential conductance exhibits(2S+1) possible peaks,corresponding to resonance tunneling via(2S+1) sublevels.At low temperature,Kondo physics dominates transport and(2S+1) Kondo peaks occur in the local density of states and conductance.These peaks originate from the spin-singlet state formed by the holes in the leads and on the dot via higher-order processes and are related to the parallel and antiparallel spin pair states.     

Metamaterial absorber and extending absorbance bandwidth based on multi-cross resonators

In this paper, we report the design, simulation, and measurements of a broadband metamaterial absorber (MA) based on a periodic array of multi-layer cross-structure resonators. A perfect narrowband MA consists of cross-structure resonator, dielectric substrate, and continuous metal films, and the absorption frequency can be tunable by changing the geometrical parameters based on L-C resonance circuit theory. Furthermore, the absorption band of our design is effectively extended by simply stacking several such structural layers with different geometrical dimensions. Finally, the 4-layer cross-structure MA is only 2 mm, which can achieve a full width at half maximum (FWHM) bandwidth of 2 GHz by numerical simulations, and 90 % bandwidth of 1.9 GHz by experiments.     

激光喷丸改善TC6钛合金组织和力学性能

为了使激光冲击强化技术能较好地应用于TC6钛合金的发动机叶片,对TC6钛合金进行试验研究。通过X射线衍射仪、透射电子显微镜等测试技术分析了不同参数下TC6钛合金的微观组织变化,用显微硬度计和残余应力测试仪分别表征表层硬度和残余应力变化,并测试材料冲击后的振动高周疲劳性能。试验结果表明:激光冲击材料后表面组织得到明显细化,随着冲击次数的增加,先后出现了高密度位错、位错胞、亚晶和纳米晶。性能方面,表面硬度在冲击一次即可提高19%,硬度影响深度达到700 m;与此同时表面残余应力最高达到-608.5 MPa,在500 m深度上仍具有-100 MPa左右的应力存在。经三次冲击后,标准疲劳试片的疲劳极限提高近20%。     

大功率半导体激光器阵列热串扰行为

以硬焊料传导制冷,30%填充因子半导体激光器阵列为例,建立了三维有限元模型,对阵列内部各发光单元之间的热串扰行为进行了分析研究。结果表明,当其连续波工作时间大于1.2 ms后,阵列内发光单元之间出现热串扰现象;当次热沉由CuW合金改为铜金刚石复合材料时,阵列内发光单元自热阻和相邻发光单元的串扰热阻降低,有效地降低了各发光单元之间的热串扰行为。保持阵列宽度、发光单元数目及发光单元周期不变,发现随阵列填充因子的增加,器件热阻以指数衰减趋势逐渐降低,而发光单元间的热串扰特性对此变化并不敏感;保持阵列单个发光单元输出功率,发光单元尺寸及阵列宽度不变,增加发光单元个数后,阵列内各发光单元之间热串扰加剧,填充因子越高阵列升温速率越快;但在最初约70 s内,包含不同数目发光单元的阵列最高温度差异仅约0.5 ℃,有利于多发光单元高填充因子器件高功率输出。     

Modeling of mixed liquor inorganic suspended solids and membrane flux at different ratio of SRT to HRT in a submerged membrane bioreactor

In order to investigate the influence of mixed liquor inorganic suspended solids (MLISS) on membrane flux at different ratio of sludge retention time (SRT) to hydraulic retention time (HRT) in a submerged membrane bioreactor (SMBR), a pilot scale test was conducted for 452 days using traditional Chinese medicine (TCM) wastewater as influent. SRT/HRT was controlled at 150, 480 and 750, respectively. The experimental results showed that the average values of MLISS were 1271.9, 1664.5 and 6898.8 mg/L at different SRT/HRT, respectively; MLISS were accumulated from 265.5 g/h to 4912.93 g/h, which indicated that SMBR could not steadily operate for a long period without sludge withdrawal. Sludge oxygen utilized rate (SOUR) decreased from 5.115 to 1.292 mgO₂/(gVSS h) and volume oxygen utilized rate (VOUR) increased from 10.84 to 18.13 mgO₂/(L h). Model of membrane flux and MLISS were developed under different temperature and operational pressure by regressions, which were then satisfactorily employed to predict the trend of membrane flux during the experiment.     

不同退火温度下氧化锌薄膜可见发光与n型导电研究

采用脉冲激光沉积法在蓝宝石衬底上制备出可见光发光良好的氧化锌薄膜, 在不同的温度下进行了后退火处理. 随着退火温度的升高, 薄膜的可见光发光发生了显著改变, 载流子浓度、迁移率、电阻率也呈现出一定的变化规律. 结合 X射线衍射、扫描电子显微镜、光致发光谱及霍尔测量, 探讨了本征氧化锌薄膜可见光发光的发射机理, 并分析了其 n型导电的原因. 关键词： 氧化锌薄膜 可见光发光 n型导电     

Least‐squares method for the Oseen equation

This article studies the least‐squares finite element method for the linearized, stationary Navier–Stokes equation based on the stress‐velocity‐pressure formulation in d dimensions (d = 2 or 3). The least‐squares functional is simply defined as the sum of the squares of the L² norm of the residuals. It is shown that the homogeneous least‐squares functional is elliptic and continuous in the norm. This immediately implies that the a priori error estimate of the conforming least‐squares finite element approximation is optimal in the energy norm. The L² norm error estimate for the velocity is also established through a refined duality argument. Moreover, when the right‐hand side f belongs only to , we derive an a priori error bound in a weaker norm, that is, the norm. © 2016 Wiley Periodicals, Inc. Numer Methods Partial Differential Eq 32: 1289–1303, 2016     

纳秒脉冲放电紫外光纤阵列检测与定位方法

峰化电容作为电磁脉冲模拟器中用于陡化脉冲输出的关键部件,在实际工程应用中易发生沿面放电和击穿现象,采用光电检测系统可对绝缘沿面放电现象进行有效分析。针对峰化电容器沿面放电监测的技术难题,研制了一套绝缘沿面放电过程光电检测系统,对绝缘沿面放电现象进行光电检测。首先提出了绝缘介质沿面放电过程光电探测系统的设计方案;其次,对系统的时延性能进行了评价;最后,完成了绝缘介质沿面放电过程定位实验,验证了光电探测系统的可行性。实验表明,该系统能够实现对放电区域的有效定位。