使用PTB7作为阳极修饰层提高有机发光二极管的性能

采用poly[[4,8-bis[(2-ethylhexyl)oxy]benzo[1,2-b:4,5-b’]dithiophene-2,6-diyl][3-?uoro-2-[(2-ethylhexyl)carbonyl]thieno[3,4-b]thiophenediyl]](PTB7)作为有机发光二极管器件的阳极修饰层,制备了结构为indium tin oxide(ITO)/PTB7(不同浓度)/N,N’-Bis(naphthalen-1-yl)-N,N’-bis(phenyl)benzidine(NPB,40 nm)/8-hydroxyquinoline(Alq3,60 nm)/LiF(1 nm)/Al的系列器件,同时研究了不同浓度的PTB7对器件性能的影响.PTB7的最佳浓度为0.25 mg/mL,器件性能得到明显的改善,起亮电压为4.3 V.当驱动电压为14.6 V时,最大亮度为45800 cd/m2,最大电流效率为9.1 cd/A.与没有PTB7修饰的器件相比,其起亮电压降低了1.9 V,最高亮度提升了78.5%.器件性能提高归因于PTB7的插入使得空穴注入和传输能力大大改善.     

Fabrication of widely tunable ridge waveguide DBR lasers for WDM-PON

We report the fabrication of widely tunable ridge waveguide distributed Bragg reflector(DBR) lasers with InGaAsP butt-joint as grating material. The shape of the butt–joint interface is found to have significant effect on the properties of the lasers. It is shown that irregular mode jumps during wavelength tuning can be avoided by a V-shaped butt–joint interface. From the fabricated device, 23 channels with 0.8 nm spacing and greater than 35 dB side mode suppression ratios are obtained. The different tuning characteristics of the ridge waveguide and the previously reported buried ridge stripe DBR lasers are discussed. Combined with the wide tuning range and the simple structure, the ridge waveguide DBR lasers are promising for use in wavelength division multiplexing passive optical networks(WDM-PONs).     

基于线性方程组数学分离模型建立光纤传感过程检测复方缬沙坦氢氯噻嗪片溶出度

基于线性方程组数学分离模型建立在线过程检测复方缬沙坦氢氯噻嗪片溶出度方法。分别扫描缬沙坦和氢氯噻嗪的紫外吸收光谱,两组分在最大吸收波长处完全重叠。根据朗伯比尔定律吸光度加和性原理,分别测定两组分在最大吸收波长处的吸光系数,建立线性方程组数学分离模型,采用光纤传感过程分析技术(FODT)检测缬沙坦氢氯噻嗪片的溶出度,并与HPLC法相比较。在规定的溶出介质中,两种成分同时实时测定,并且FODT累积溶出度与HPLC法相比较结果无显著性差异(p>0.05)。不同批次药物的溶出行为一致,说明制剂工艺稳定,均匀度好。溶出曲线显示缬沙坦溶出快于并高于氢氯噻嗪,且30 min时两组分的溶出度均大于80%符合美国药典规定。结果表明,应用线性方程组数学分离模型结合FODT法可实现复方缬沙坦氢氯噻嗪片中双组分溶出度的同时检测,并可提供双组分的溶出过程曲线和全部溶出数据,直观反映各组分在各溶出时段的快慢,为此药建立标准提供依据。与HPLC法单点数据相比优势明显,更有利于药品评价和抽验质量分析。     

Polarization of plane wave propagating inside elastic hexagonal system solids

Based on the reported physical parameters for hexagonal system solids,we have calculated the effects of anisotropy on polarization of plane P-wave propagation.Herein we report the results of calculations and the newly observed physical phenomena.It is found that,for a given propagation,if the polarization is parallel to the wave vector,so also to the Poynting vector.In such a case,the phase velocity is identical to the energy velocity;the quasi P-wave degenerates to a pure P-wave along the propagation.It is also noted that if the polarization is parallel to the Poynting vector but not to the wave vector,the propagating wave cannot be a pure P-wave.Furthermore,the polarization in a quasi P-wave may deviate from the wave vector for more than 45°,but the deviation from the Poynting vector is always less than 45°.The energy velocity of a quasi SV-wave can be larger than that of the quasi P-wave in some propagation directions,even though the phase velocity of a quasi SV-wave may never be larger than either the phase velocity or energy velocity of the quasi P-wave.Finally,in case of parameters ε=0 and δ*≠0,the polarization of a quasi P-wave has an observed symmetry at a 45°phase angle.The anisotropy of a hexagonal system solid determines if a pure P-wave can be created and what the propagation direction is for a plane wave propagating inside such a hexagonal system solid.     

高温超导滤波器的光刻工艺

根据高温超导薄膜的特点,详细讨论了制备高温超导滤波器的光刻技术及在制备的各环节中需注意的问题,实验结果表明:此种方法提高了制备的成功率。     

High-power, high-efficiency cw diode-pumped Tm:YAP laser emitting at 1.99?μm

We elaborate a high-power, high-efficiency cw Tm:YAP laser dual-end-pumped by the laser diode. With 41.9?W pumping power, we obtain a maximum cw output power of 14.7?W at 1988?nm with a slope efficiency of 43.8%, corresponding to an optical conversion efficiency of 35.1%. At the maximum laser output, we measure a beam quality of M ²?~?1.9.     

Evaluation of an oral carrier system in rats: bioavailability and gastrointestinal absorption properties of curcumin encapsulated PBCA nanoparticles

A new oral delivery system, polybutylcyanoacrylate nanoparticles (PBCNs), was introduced to improve the oral bioavailability of curcumin (CUR), a poorly soluble drug. The formulation was optimized by orthogonal design and the optimal PBCNs loading CUR exhibited a spherical shape under transmission electron microscopy with a range of 40?C400?nm. Physicochemical state of CUR in PBCN was investigated by X-ray diffraction and the possible structure changes occurring in CUR after conjugating with polybutylcyanoacrylate were studied with FTIR. The results indicated that CUR in PBCN was in a non-crystalline state and CUR was encapsulated in PBCN without chemical reaction. The oral pharmacokinetic study was conducted in rats and the relative bioavailability of CUR encapsulated PBCNs to the crude CUR was more than 800%. The in situ absorption experiment in rat intestine indicated the absorption was first order with passive diffusion mechanism. The absorption results in various segments of intestine showed that the main absorption sites were ileum and colon. It can be concluded that PBCNs as an oral carrier can significantly improve the oral absorption of a poorly soluble drug.     

Enhanced electrochemical properties of LiMnPO4/C via doping with Cu

Li_0.98Cu_0.01MnPO₄/C composite cathode materials for lithium ion battery are synthesized by sol-gel method followed by heat treatment in the air. Field-emission scanning electron microscopy measurements show that both firing temperature and carbon content affect the morphology of the end products. X-ray powder diffraction analysis indicates that the samples are olivine-structured. The galvanostatic charge?Cdischarge results show that the optimal firing temperature registers 500°C and that the electrochemical performances of Li_0.98Cu_0.01MnPO₄/C are improved by elevating its carbon amount. The cyclic ability and rate performances of LiMnPO₄ are greatly improved by doping Cu.     

Effect of the thermal and hydrothermal treatment on textural properties of Zr-MCM-41 mesoporous molecular sieve

Zr-containing mesoporous molecular sieves were synthesized by hydrothermal method using cetyltrimethyl ammonium bromide as a template and sodium silicate and zirconium sulfate as raw materials. The structure and morphology of the synthesized samples were characterized via various physicochemical methods, including X-ray diffraction (XRD), transmission electron microscopy (TEM), Fourier transform infrared (FT-IR) spectroscopy, solid state nuclear magnetic resonance (²⁹Si MAS-NMR) techniques, thermal gravimetric-differential scanning calorimeter (TG-DSC) and N₂ physical adsorption, respectively. The effect of the different initial ZrO₂:SiO₂ molar ratio, the different thermal treatment temperature and the different hydrothermal treatment time on textural property was investigated. The experimental results reveal that the as synthesized samples possess a typical mesoporous structure of MCM-41. On the other hand, the specific surface area and pore volume of the synthesized Zr-MCM-41 mesoporous molecular sieve decrease with the increase of the amount of zirconium incorporated in the starting material, the rise of thermal treatment temperature and the prolonging of hydrothermal treatment time, the mesoporous ordering becomes poor. Also, when the molar ratio of ZrO₂:SiO₂ in the starting material is 0.1, the mesoporous structure of the Zr-MCM-41 mesoporous molecular sieve still retains after calcination at 750 °C for 3 h or hydrothermal treatment at 100 °C for 6 d, and have specific surface areas of 423.9 and 563.9 m²/g, respectively.     

Biosynthesis and magnetic properties of mesoporous Fe3O4 composites

Magnetic Fe₃O₄ materials with mesoporous structure are synthesized by co-precipitation method using yeast cells as a template. The X-ray diffraction (XRD) pattern indicates that the as-synthesized mesoporous hybrid Fe₃O₄ is well crystallized. The Barrett-Joyner-Halenda (BJH) models reveal the existence of mesostructure in the dried sample which has a specific surface area of 96.31 m²/g and a pore size distribution of 8-14 nm. Transmission electron microscopy (TEM) measurements confirm the wormhole-like structure of the resulting samples. The composition and chemical bonds of the Fe₃O₄/cells composites are studied by Fourier transform infrared (FT-IR) spectroscopy. Preliminary magnetic properties of the mesoporous hybrid Fe₃O₄ are characterized by a vibrating sample magnetometer (VSM). The magnetic Fe₃O₄/cells composites with mesoporous structure have potential applications in biomedical areas, such as drug delivery.