High-speed deposition of RE123 film with large current capacity by hot-wall type PLD system

We have studied a hot-wall heating system to produce GdBa₂Cu₃O_y (GdBCO) films with large critical currents (I_c) at a high production rate by a pulsed-laser-deposition (PLD) method. GdBCO films fabricated at a production rate of 30 m/h under the optimized conditions, especially a distance of 95 mm between the target and the substrate (T–S), exhibited high critical current densities (J_c) of about 3 MA/cm² and I_c over 300 A at a thickness of 1–2 μm. Furthermore, long GdBCO tapes prepared by repeated depositions at each tape-passing speed of 80 m/h showed uniform I_c distribution along the longitudinal direction, because the hot-wall system enabled to stabilize temperature within a few degrees at 800 °C. A 170 m long tape with I_c over 600 A was successfully fabricated at a production rate of 16 m/h using a laser power of 360 W.     

Synthesis of Star-Shaped Polymers via Coordination of Bipyridyl-Terminated Polyoxyethylene with Metal Ions

Abstract

This paper describes the synthesis of various star-shaped polymers by means of complexation of bipyridyl-terminated polyoxyethylene with Ru(II) ion. Three kinds of bipyridyl-terminated polyoxyethylenes of different molecular weights were prepared from the corresponding polyoxyethylene monomethyl ethers with narrow molecular weight distributions. Bipyridyl was found to be introduced quantitatively at the end of the polymers based on the results of UV spectra. The formation of a star-shaped polymer was carried out by the reaction of RuCl₃ with three equivalents of bipyridyl-terminated polyoxyethylene. The UV spectrum of the star-shaped polymer obtained supported the formation of a typical Ru(II) tris(bipyridyl) complex. From the results of GPC, the star-shaped polymer obtained had a higher molecular weight than the pre-polymer and showed a narrow molecular weight distribution. In the case of a Ni(II) or a Co(II) complex, however, the star-shaped polymer was found to be dissociated into three linear prepolymers under the conditions of GPC measurement.     

Enhancing the Cellulose-Degrading Activity of Cellulolytic Bacteria CTL-6 (Clostridium thermocellum) by Co-Culture with Non-cellulolytic Bacteria W2-10 (Geobacillus sp.)

The effect of a non-cellulolytic bacterium W2-10 (Geobacillus sp.) on the cellulose-degrading activity of a cellulolytic bacterium CTL-6 (Clostridium thermocellum) was determined using cellulose materials (paper and straw) in peptone cellulose solution (PCS) medium under aerobic conditions. The results indicated that in the co-culture, addition of W2-10 resulted in a balanced medium pH, and may provide the required anaerobic environment for CTL-6. Overall, addition of W2-10 was beneficial to CTL-6 growth in the adverse environment of the PCS medium. In co-culture with W2-10, the CTL-6 cellulose degradation efficiency of filter paper and alkaline-treated wheat straw significantly increased up to 72.45 and 37.79 %, respectively. The CMCase activity and biomass of CTL-6 also increased from 0.23 U ml^?1 and 45.1 μg ml^?1 (DNA content) up to 0.47 U ml^?1 and 112.2 μg ml^?1, respectively. In addition, co-culture resulted in accumulation of acetate and propionate up to 4.26 and 2.76 mg ml^?1. This was a respective increase of 2.58 and 4.45 times, in comparison to the monoculture with CTL-6.     

Mannose‐Binding Geometry of Pradimicin A

Pradimicins (PRMs) and benanomicins are the only family of non‐peptidic natural products with lectin‐like properties, that is, they recognize D ‐mannopyranoside (Man) in the presence of Ca²⁺ ions. Coupled with their unique Man binding ability, they exhibit antifungal and anti‐HIV activities through binding to Man‐containing glycans of pathogens. Notwithstanding the great potential of PRMs as the lectin mimics and therapeutic leads, their molecular basis of Man recognition has yet to be established. Their aggregate‐forming propensity has impeded conventional interaction analysis in solution, and the analytical difficulty is exacerbated by the existence of two Man binding sites in PRMs. In this work, we investigated the geometry of the primary Man binding of PRM‐A, an original member of PRMs, by the recently developed analytical strategy using the solid aggregate composed of the 1:1 complex of PRM‐A and Man. Evaluation of intermolecular distances by solid‐state NMR spectroscopy revealed that the C2–C4 region of Man is in close contact with the primary binding site of PRM‐A, while the C1 and C6 positions of Man are relatively distant. The binding geometry was further validated by co‐precipitation experiments using deoxy‐Man derivatives, leading to the proposal that PRM‐A binds not only to terminal Man residues at the non‐reducing end of glycans, but also to internal 6‐substituted Man residues. The present study provides new insights into the molecular basis of Man recognition and glycan specificity of PRM‐A.     

Controlling Energy Gaps of π-Conjugated Polymers by Multi-Fluorinated Boron-Fused Azobenzene Acceptors for Highly Efficient Near-Infrared Emission

We demonstrate that multi-fluorinated boron-fused azobenzene (BAz) complexes can work as a strong electron acceptor in electron donor-acceptor (D-A) type π-conjugated polymers. Position-dependent substitution effects were revealed, and the energy level of the lowest unoccupied molecular orbital (LUMO) was critically decreased by fluorination. As a result, the obtained polymers showed near-infrared (NIR) emission (λ_PL=758–847 nm) with high absolute photoluminescence quantum yield (Φ_PL=7–23%) originating from low-lying LUMO energy levels of the BAz moieties (−3.94 to −4.25 eV). Owing to inherent solid-state emissive properties of the BAz units, deeper NIR emission (λ_PL=852980 nm) was detected in film state. Clear solvent effects prove that the NIR emission is from a charge transfer state originating from a strong D-A interaction. The effects of fluorination on the frontier orbitals are well understandable and predictable by theoretical calculation with density functional theory. This study demonstrates the effectiveness of fluorination to the BAz units for producing a strong electron-accepting unit through fine-tuning of energy gaps, which can be the promising strategy for designing NIR absorptive and emissive materials.     

Hyperpolarized 13C Magnetic Resonance Imaging of Fumarate Metabolism by Parahydrogen-induced Polarization: A Proof-of-Concept in vivo Study

Hyperpolarized [1-¹³C]fumarate is a promising magnetic resonance imaging (MRI) biomarker for cellular necrosis, which plays an important role in various disease and cancerous pathological processes. To demonstrate the feasibility of MRI of [1-¹³C]fumarate metabolism using parahydrogen-induced polarization (PHIP), a low-cost alternative to dissolution dynamic nuclear polarization (dDNP), a cost-effective and high-yield synthetic pathway of hydrogenation precursor [1-¹³C]acetylenedicarboxylate (ADC) was developed. The trans-selectivity of the hydrogenation reaction of ADC using a ruthenium-based catalyst was elucidated employing density functional theory (DFT) simulations. A simple PHIP set-up was used to generate hyperpolarized [1-¹³C]fumarate at sufficient ¹³C polarization for ex vivo detection of hyperpolarized ¹³C malate metabolized from fumarate in murine liver tissue homogenates, and in vivo ¹³C MR spectroscopy and imaging in a murine model of acetaminophen-induced hepatitis.     

Second-harmonic-generation microscope using eight-segment polarization-mode converter to observe three-dimensional molecular orientation

We developed a compact polarization-mode converter for microscopy to control three-dimensional polarization at the focus. The converter consisted of two homogeneously aligned liquid-crystal spatial light modulators with eight independently controllable electrodes (segments), and a quarter-waveplate. The converter converted a linearly polarized beam to three polarization modes: two orthogonal linear polarizations and a pseudo-radial polarization. We applied the converter to second-harmonic-generation microscopy and demonstrated the detection of three-dimensional molecular orientation.     

Unequally spaced multiple mid-infrared wavelength generation using an engineered quasi-phase-matching device

We propose a novel quasi-phase-matched (QPM) device that can generate unequally spaced multiple wavelengths. Unequally spaced multiple QPM peaks can be obtained by employing the optimized phase modulation of a periodic domain structure. We fabricated a LiNbO3 waveguide device for 3.2-3.4 microm band difference frequency generation based on the design. Using the multiple mid-infrared outputs, we demonstrate the detection of multiple hydrocarbon gases, namely, methane, ethylene, and ethane.     

Development of variable‐magnification X‐ray Bragg optics

A novel X‐ray Bragg optics is proposed for variable‐magnification of an X‐ray beam. This X‐ray Bragg optics is composed of two magnifiers in a crossed arrangement, and the magnification factor, M, is controlled through the azimuth angle of each magnifier. The basic properties of the X‐ray optics such as the magnification factor, image transformation matrix and intrinsic acceptance angle are described based on the dynamical theory of X‐ray diffraction. The feasibility of the variable‐magnification X‐ray Bragg optics was verified at the vertical‐wiggler beamline BL‐14B of the Photon Factory. For X‐ray Bragg magnifiers, Si(220) crystals with an asymmetric angle of 14° were used. The magnification factor was calculated to be tunable between 0.1 and 10.0 at a wavelength of 0.112 nm. At various magnification factors (M≥ 1.0), X‐ray images of a nylon mesh were observed with an air‐cooled X‐ray CCD camera. Image deformation caused by the optics could be corrected by using a 2 × 2 transformation matrix and bilinear interpolation method. Not only absorption‐contrast but also edge‐contrast due to Fresnel diffraction was observed in the magnified images.