Assessment of two‐equation turbulence modelling for high Reynolds number hydrofoil flows

This paper presents an evaluation of the capability of turbulence models available in the commercial CFD code FLUENT 6.0 for their application to hydrofoil turbulent boundary layer separation flow at high Reynolds numbers. Four widely applied two‐equation RANS turbulence models were assessed through comparison with experimental data at Reynolds numbers of 8.284×106 and 1.657×107. They were the standard k–εmodel, the realizable k–εmodel, the standard k–ωmodel and the shear‐stress‐transport (SST) k–ωmodel. It has found that the realizable k–εturbulence model used with enhanced wall functions and near‐wall modelling techniques, consistently provides superior performance in predicting the flow characteristics around the hydrofoil. Copyright © 2004 John Wiley & Sons, Ltd.     

Experimental investigation and theoretical modeling of liquid entrainment in a horizontal tee with a vertical-up branch

This article describes a comprehensive literature review of liquid entrainment in horizontal pipes with vertical-up branches. Deficiencies in the available data and correlations were identified. The Air–water Test Loop for Advanced Thermal–hydraulic Studies (ATLATS) was constructed and entrainment onset and steady-state data were collected for a wide range of flow conditions. Using new insights gained from experimental testing, the authors developed a model for predicting the onset of entrainment and steady-state entrainment rate. Previously published correlations, along with the new model, are compared against all available data. The new model shows very good agreement with the onset data, but is not very good at predicting branch quality at high liquid flow rates.     

A laser Doppler anemometry technique for Reynolds stresses measurement

A technique is described for the measurement of all components of mean velocity and Reynolds stresses, in a complex turbulent flow where achieving coincidence data acquisition is difficult. The method is based on data recorded using four orientations of the laser probe. It is shown that the measurement errors are not the same for all the components of the Reynolds tensor, but they are sufficiently small to give a good accuracy. An application to a turbomachinery flow is given to illustrate the method.     

Real-time color holographic interferometry devoted to 2D unsteady wake flows

A new optical technique based on real time holographic interferometry in true colors has been implemented around the transonic wind tunnel of the ONERA-Lille center to analyze 2D unsteady wake flows. Tests realized in color interferometry, real time and double exposure, use simultaneously three wavelengths of a continuous waves laser (argon and krypton mixed) and holograms are recorded on silver-halide single-layer panchromatic Slavich PFG03c plates. The very principle of real-time true color holographic interferometry uses three primary wavelengths (red, green and blue) to record, under no-flow conditions, the interference among the three measurement beams and the three reference beams simultaneously on a single reference hologram. After the holographic plate is developed, it is placed on the test setup again in the position it occupied during exposure and the hologram is illuminated again by the three reference beams and three measurement beams. A flat, uniform color can then be observed behind the hologram. So a horizontal, vertical, or even circular fringe pattern can be formed and the achromatic central fringe can be made out very clearly. The single color is used to determine the path difference zero on the interferograms. The flow studied was the unsteady flow downstream of a cylinder placed crosswise in the test section. A sequence of hundred interferograms was recorded on the flow around the cylinder at Mach 0.37. The vortex formation and dissipation phases can be seen very clearly, along with the fringe beat to either side of the cylinder.     

The glow curve structure for the LiF:Mg,Cu,Na,Si TL detector with dopants concentrations and sintering temperatures

The glow curve structures for LiF:Mg,Cu,Na,Si TL detectors with various dopant concentrations and sintering temperatures were investigated for the improvement of the glow curve structure and sensitivity of the TL detector. The dopant concentrations were varied over the following ranges: Mg (0–0.25 mol%), Cu (0–0.07 mol%), Na and Si (0–1.5 mol%). With increasing Cu concentration, the intensity of the main peak was intensified and reached a maximum at a concentration of 0.05 mol%. The high-temperature peak was reduced. The dependency of the main peak intensity on the Mg concentration exhibits a sharp maximum at 0.2 mol%. The intensity of the high-temperature peak tends to rise slightly with increasing Mg concentration. It was found that the optimum concentrations of the dopants in the LiF:Mg,Cu,Na,Si TL material are Mg: 0.2 mol%, Cu: 0.05 mol%, Na and Si: 0.9 mol%. The dependency of the main peak intensity on sintering temperature exhibits a very sharp maximum at 830°C. The high-temperature peak was rapidly reduced after 825°C.     

Kinetic interpretation of the structural-time criterion for fracture

The incubation-period-based criterion for fracture is considered in terms of the Zhurkov kinetic model of fracture. Within the kinetic model, fracture is treated as a continuously developing process, which starts immediately after the application of a tensile load to a sample and consists in breaking of the interatomic bonds and gradual accumulation of broken bonds in the material in the course of a fracture test. For certain materials, the inclusion of the thermal-fluctuation mechanism for fracture in the incubation-period-based criterion significantly affects the position of the static branch of the time dependence of strength. Time dependences of strength are calculated for a number of materials. The experimental data are analyzed using the structural-time criterion for fracture, which allows one to obtain a unified time dependence of strength for quasi-static and high-rate short-term loadings. The temperature dependence of the incubation period (latent time) is calculated analytically, and a relation is found between the latent fracture time and the thermal vibration frequency of atoms.     

Refraction of surface spin waves in spatially inhomogeneous ferrodielectrics with biaxial magnetic anisotropy

The refractive index of surface spin waves propagating in a ferromagnetic medium with a nonuniform distribution of the parameters of uniaxial and orthorhombic magnetic anisotropies and exchange coupling is determined within the spin-density formalism. The coefficients of reflection and transmission of spin waves at the interface between two homogeneous magnets with different constants of uniaxial and orthorhombic magnetic anisotropies, exchange coupling, and saturation magnetization are calculated. The dependences of the intensity of a reflected wave and the refractive index on the wave frequency and the strength of an external dc homogeneous magnetic field are determined.     

Giant piezoelectric and dielectric enhancement in disordered heterogeneous systems

Effective complex piezoelectric and dielectric constants of disordered heterogeneous systems, such as statistical mixtures consisting of spheroidal particles of the same orientation but with random distribution in space, are studied. It is found for the first time that, in such systems, there exists giant piezoelectric enhancement accompanied by giant relaxation of piezoelectric coefficients and permittivity. The piezoelectric and dielectric spectra differ considerably from the Debye spectra and have a Cole-Cole character. The dependence of the effects considered on the aspect ratios of the spheroids is investigated. The physical mechanisms responsible for the anomalous behavior of the piezoelectric coefficients and permittivity are considered.     

Galvano-dipolar effect

The phenomenology of the photogalvanic effect permits prediction of a number of physical phenomena, the most interesting of which is the galvano-dipolar effect. This effect consists in the appearance of an electric dipole moment in a sample through which an electric current is passed. A possible microscopic mechanism of this phenomenon, which can be realized in centrosymmetric media as well, is considered.