RGDS-fuctionalized alginates improve the survival rate of encapsulated embryonic stem cells during cryopreservation

Cryopreservation of stem cells, especially embryonic stem cells, is problematic because of low post-thaw cell survival rates and spontaneous differentiation following recovery. In this investigation, mouse embryonic stem cells (mESCs) were encapsulated in arginine-glycine-aspartic acid-serine (RGDS)-coupled calcium alginates (1.2 percent, w/v), allowed to attach to the substratum and then cryopreserved in 10 percent (v/v) dimethyl sulfoxide (DMSO) solution at a slow cooling rate of 1 C per min. RGDS coupling to alginate was confirmed by Transmission Fourier Transform Infra-Red spectroscopy (T-FTIR) and quantified by using ninhydrin-Ultraviolet/Visible light (ninhydrin-UV/VIS) assay. Flow cytometry data showed that mESCs cryopreserved in RGDS-alginate beads had a higher expression of stem cell markers compared with cells cryopreserved in suspension or cells cryopreserved in unmodified alginates. Cell viability after thawing was assessed using trypan blue exclusion assay and monitored using Alamar blue assay for 6 hours. It was shown that post-thaw cell survival rate was significantly higher for cells encapsulated in RGDS-modified alginate (93 ± 2 percent, mean and standard error) than those in suspension (52 ± 2 percent) or in unmodified alginates (62 ± 3 percent). These results showed that cells encapsulated and attached to a substratum have better survival rate and stem cell marker expression 24 hours after cryopreservation than those in suspension. Encapsulation in RGDS-alginate was optimized for peptide concentration, cryoprotective agent loading time and cooling rate. The best result was obtained when using 12.5 mg peptide per g alginate, 30 minutes loading time and 1 C per min cooling rate.     

Elementary heterogeneously polarized field modeling

An approach for experimental modeling of elementary field cells with heterogeneous polarization is proposed. It is shown that such cells may be obtained by the superposition of orthogonally linearly polarized waves with relatively simple phase surfaces and close intensities. The experimental arrangement for obtaining elementary field cells is suggested. The characteristics of a polarization cell may be easily changed by the change of superposed beam parameters. The results of experimental investigation are presented.     

High spatial resolution distributed strain sensor based on linear chirped fiber Bragg grating and fiber loop ringdown spectroscopy

A simple sensor system for high spatial resolution distributed strain field measurement is proposed and demonstrated experimentally. The fiber loop ringdown technique combined with a linear chirped fiber Bragg grating is used to realize the high spatial resolution. A proof-of-concept distributed strain sensor with 2?mm spatial resolution is realized. The sensor network is also explored and researched experimentally. The proposed technique suggests a broad range of applications for real-time distributed physical parameter sensing, such as strain or temperature.     

Continuous-wave fiber cavity ring-down measurements using frequency-shifted interferometry

We present a spatial-domain fiber cavity ring-down (CRD) technique that does not require optical pulses for time-resolved detection. Instead of measuring the intensity decay rate of an optical pulse in the time domain as in conventional CRD experiments, we measure the decay rate of a CW signal in a ring-down cavity (RDC) using frequency-shifted interferometry in the spatial domain, as a function of distance traveled by the light. As a proof-of-concept demonstration, we measured fiber bend loss in a loop RDC using this technique, and a cavity loss change as low as 0.0135 dB induced by every fiber turn on a mandrel was unambiguously discerned.     

Temperature-independent silicon subwavelength grating waveguides

We demonstrate, by experiment and numerical calculations, temperature-independent subwavelength grating waveguides with a periodic composite core composed of alternating regions of silicon and SU-8 polymer. The polymer has a negative thermo-optic (TO) material coefficient that cancels the large positive TO effect of the silicon. Measurements and Bloch mode calculations were carried out over a range of silicon-polymer duty ratios. The lowest measured TO coefficient at a wavelength of 1550 nm is 1.8×10(-6) K(-1); 2 orders of magnitude smaller than a conventional silicon photonic wire waveguide. Calculations predict the possibility of complete cancellation of the silicon waveguide temperature dependence.     

Broadband phase noise suppression in a Yb-fiber frequency comb

We report a simple technique to suppress high-frequency phase noise of a Yb-based fiber optical frequency comb using an active intensity noise servo. Out-of-loop measurements of the phase noise using an optical heterodyne beat with a cw laser show suppression of phase noise by ≥7?dB out to Fourier frequencies of 100?kHz with a unity-gain crossing of ～700?kHz. These results are enabled by the strong correlation between the intensity and phase noise of the laser. Detailed measurements of intensity and phase noise spectra, as well as transfer functions, reveal that the dominant phase and intensity noise contribution above ～100?kHz is due to amplified spontaneous emission or other quantum noise sources.     

Coherent interference induced transparency in self-coupled optical waveguide-based resonators

We propose a self-coupled optical waveguide (SCOW)-based resonator to generate an optical resonance analogous to electromagnetically induced transparency (EIT). The EIT-like effect is formed by the coherent interference between two resonance paths inherent to the SCOW resonator. For cascaded SCOW resonators, the spectrum they produce is significantly affected by the phase shift between them, with the EIT-like peak flattened or split as the two extreme cases. We also investigate the dispersion characteristics of an infinite array of SCOW resonators and show that the dispersion relation and group index in the EIT subband can be greatly changed by a small phase shift between the SCOW resonators.     

External cavity diode laser with kilohertz linewidth by a monolithic folded Fabry-Perot cavity optical feedback

We present a extended-cavity diode laser (ECDL) with kilohertz linewidth by optical feedback from a monolithic folded Fabry-Perot cavity (MFC). In our experiments, an MFC replaces the retroreflecting mirror in the traditional ECDL configuration. Beat-note measurements between this MFC-ECDL and a narrow-linewidth reference laser are performed and demonstrate that the linewidth of this MFC-ECDL is about 6.8 kHz. Phase locking of this MFC-ECDL to the reference laser is achieved with a unity gain as small as 10.2 kHz.     

A simple solution-immersion process for the fabrication of superhydrophobic cupric stearate surface with easy repairable property

The present work reports a simple and time-saving method to fabricate cupric stearate film on zinc substrate by a solution-immersion process. Superhydrophobic surfaces are conventionally prepared employing two steps: roughening a surface and lowering its surface energy. The fabrication of superhydrophobic cupric stearate surface is reported using a one-step process by immersing a zinc plate coated with copper into the stearic acid solution, simplifying the complexity of two different steps involved in the conventional methods. The surface of the zinc plate coated with copper is found to be covered with low surface energy cupric stearate film providing the water contact angle of 160 ± 1° with the rolling off properties. In addition, the damaged superhydrophobic surface can restore superhydrophobicity property by immersing the surface into the stearic acid solution again.     

Optical properties of p-type CuAlO2 thin film grown by rf magnetron sputtering

We report the structural and optical properties of copper aluminium oxide (CuAlO₂) thin films, which were prepared on c-plane sapphire substrates by the radio frequency magnetron sputtering method. X-ray photoelectron spectroscopy (XPS) along with X-ray diffraction (XRD) analysis confirms that the films consist of delafossite CuAlO₂ phase only. The optical absorption studies show the indirect and direct bandgap is 1.8 eV and 3.45 eV, respectively. Room temperature photoluminescence (PL) measurements show three emission peaks at 360 nm (3.45 eV), 470 nm (2.63 eV) and 590 nm (2.1 eV). The first one is near band edge emission while the other two are originated from defects.