Mechanical properties of polyester polymer-concrete

The properties of a polymer-concrete composed of polyester matrix and locally available rock aggregate are investigated. The formula of the concrete is found by an experimental-calculation approach in such a way as to attain a closer packing of the aggregate particles on the one hand, and to ensure the needed processing characteristics (placeability) of the mix on the other. It is shown experimentally that the material obtained has a rather high compression strength. Under prolonged compression loads, the polymer-concrete exhibits a noticeable creep behavior with a linear relation between the creep strains and stresses. After the action of half the ultimate load over 3000 h, the total strains exceed the instantaneous ones by 2.0 to 2.2 times. The accumulation of irreversible strains is also observed; however, their contribution to the total strain is small. It is found that the stress-strain relation can be represented by the equation of linear hereditary creep theory.Institute of Polymer Mechanics, University of Latvia, Riga, LV-1006, Latvia. Translated from Mekhanika Kompozitnykh Materialov, Vol. 35, No. 2, pp. 147–162, March–April, 1999.     

非晶调制多层膜Nb/Si中的互扩散研究

利用原位Ｘ射线衍射技术得到非晶调制多层膜Ｎｂ／Ｓｉ中的互扩散系数与退火温度的关系，调制周期Ｌ＝３.２ｎｍ的非晶调制多层膜是用粒子溅射方法制备的．温度范围为４２３—５２３Ｋ的有效互扩散系数通过原位测量多层膜的一级调制峰强度与退火温度之间的关系而得到．利用缺陷陷阱延迟扩散机制解释了所得到的扩散系数与退火温度的关系．建立了可以解释较小前置系数的模型 关键词：     

Three-dimensional atom probe study of the segregation behaviour of Ni91Pt9 alloy after sputtering

To investigate local ordering and segregation phenomenon in a Ni91Pt9-alloy after sputtering and annealing a 3D optical atom probe (OAP) has been used. The specimen tips have been prepared from polycrystalline samples. To sputter the samples a separate preparation chamber with a scannable Ar-sputter-gun is connected to the OAP vessel. When necessary, the sample can be electrically heated to induce segregation and cure the altered layer. After a heat treatment of a Ni91 at. %Pt 9 at.% specimen at 1100 K the surface of a (111)-oriented specimen is enriched in platinum by a factor of two in relation to the bulk. The phenomenon of short-range ordering has been investigated on the surface and in the subsurface volume. A 3D reconstruction of this annealed NiPt specimen shows regions with high concentration of platinum that gives an indication at short-range ordering. Uniform sputtering of the tip without a heat treatment induces a decisive depletion of Pt on the surface and the following subatomic layers. The atom-probe results of specimens in thermal equilibrium are in close agreement to further surface sensitive results obtained from Ion Scattering Spectroscopy (ISS) and Auger Electron Spectroscopy (AES).     

因素空间理论与知识表示的数学框架（Ⅷ）─—变权综合原理

本文是文［１－７］的继续，研究变权综合问题，从确定变权的经验公式入手引出了变权原理，给出了变权的公理化定义，讨论了与之有关的均衡函数及其梯度向量。     

A simple method improving the analyzing accuracy of circular groove guide

A simple method is introduced to improve the analysing accuracy of circular groove guide. With this method, the characteristic equation of circular groove guide is derived and its solution is given and discussed.The Project Supported by National Natural Science Foundation of P.R.China     

An investigation of the Al2O3-CdSe interface in accumulation

The Al₂O₃−CdSe interface of a thin-film transistor is investigated in the frequency range 30 Hz-30 kHz under weak depletion and accumulation. The surface states are, most likely, located in the insulator Al₂O₃ with a concentration varying from 4·10¹⁸ to 10¹⁹ cm⁻³ eV⁻¹. The surface states have a negligible influence on the thin-film transistor operation.     

铁分子Fe2的自旋极化效应

采用密度泛函方法(B3P86)对 Fe_2分子结构进行了优化.计算结果中未观察到自旋污染,基态波函数与高态波函数并未混杂,结果表明,Fe_2中有8个未配对电子,这些电子空间分布不同和自旋平行产生的自旋极化效应,使 Fe_2能量最低.计算结果表明,Fe_2分子的基态是~9∑_g~ ,并非~7Δ_u,进而表明 Fe_2的自旋平行效应比电子自旋配对效应要强.计算得到该分子基态的二阶、三阶和四阶力常数分别为1.4115×10~(-2)aJ/nm~2、-37.1751×10~3aJ/nm~3和 98.7596×10~4aJ/nm~4；光谱数据ω_eχ_e、B_e、α_e分别为0.3522、0.0345、 0.4963×10~(-4)cm~(-1)；离解能为3.5522eV,平衡键长为0.2137nm,振动频率为292.914cm~(-1)；并得到了 Murrel-Sorbie 函数.     

Structural and thermodynamic properties of AlB2 compound

We employ a first-principles plane wave method with the relativistic analytic pseudopotential of Hartwigsen, Goedecker and Hutter (HGH) scheme in the frame of DFT to calculate the equilibrium lattice parameters and the thermodynamic properties of AlB₂ compound with hcp structure. The obtained lattice parameters are in good agreement with the available experimental data and those calculated by others. Through the quasi-harmonic Debye model, obtained successfully are the dependences of the normalized lattice parameters a/a₀ and c/c₀ on pressure P, the normalized primitive cell volume V/V₀ on pressure P, the variation of the thermal expansion α with pressure P and temperature T, as well as the Debye temperature \Theta_D and the heat capacity C_V on pressure P and temperature T.     

Optimization of the surface texture for silicon carbide sliding in water

Surface texturing has been recognized as an effective means to improve the tribological performances of sliding surfaces. Usually, generation additional hydrodynamic pressure to increase the load carrying capacity is regarded as the most significant effect of surface texture. In the case of silicon carbide sliding against identical material in water, the experimental results indicate that surface texture is also helpful to improve the running-in progress to smooth the contact surfaces, showing another reason to result in low friction. Based on the consideration of enhancing the generation of hydrodynamic pressure and improving running-in progress, a surface texture pattern, which was combined with large (circle, 350 μm in diameter) and small (rectangular, 40 μm in length) dimples, was designed to maximize the texture effect on the load carrying capacity of SiC surfaces sliding in water. The friction coefficient of such textured surface was evaluated and compared with that of untextured and those only with large or small dimples only. The friction reduction mechanisms of the patterns with different dimples in size are discussed.