Role of hot-electron preheating in the compression of direct-drive imploding targets with cryogenic D2 ablators

The compression of direct-drive, spherical implosions is studied using cryogenic D2 targets on the 60-beam, 351-nm OMEGA laser with intensities ranging from approximately 3x10(14) to approximately 1x10(15) W/cm2. The hard-x-ray signal from hot electrons generated by laser-plasma instabilities increases with laser intensity, while the areal density decreases. Mitigating hot-electron production, by reducing the laser intensity to approximately 3x10(14) W/cm2, results in areal density of the order of approximately 140 mg/cm2, in good agreement with 1D simulations. These results will be considered in future direct-drive-ignition designs.     

Correction of B0 susceptibility induced distortion in diffusion-weighted images using large-deformation diffeomorphic metric mapping

Geometric distortion caused by B0 inhomogeneity is one of the most important problems for diffusion-weighted images (DWI) using single-shot, echo planar imaging (SS-EPI). In this study, large-deformation, diffeomorphic metric mapping (LDDMM) algorithm has been tested for the correction of geometric distortion in diffusion tensor images (DTI). Based on data from nine normal subjects, the amount of distortion caused by B0 susceptibility in the 3-T magnet was characterized. The distortion quality was validated by manually placing landmarks in the target and DTI images before and after distortion correction. The distortion was found to be up to 15 mm in the population-averaged map and could be more than 20 mm in individual images. Both qualitative demonstration and quantitative statistical results suggest that the highly elastic geometric distortion caused by spatial inhomogeneity of the B0 field in DTI using SS-EPI can be effectively corrected by LDDMM. This postprocessing method is especially useful for correcting existent DTI data without phase maps.     

Theoretical and experimental investigation of thermal effects in a high power Yb-doped double-clad fiber laser

In this paper, based on the thermal conduction equations and the steady-state rate equations, a theoretical and numerical analysis of thermal effects is investigated for a single end pumped Yb-doped double-clad fiber laser (YDDC). The distributions of signal power and temperature for different pump powers and fiber parameters are compared. According to the results, the parameters of the optical-cavity have been optimized and an effective method has been adopted to reduce the thermal effects in an experimental investigation. As a result, an output power of 621 W has been obtained with a slope efficiency of 78%.     

A Novel Highly Sensitive and Selective Fluorescent Sensor for Imaging Copper (II) in Living Cells

In this work, we designed and synthesized a novel quinolin-based derivative which exhibited signaling behaviors for Cu²⁺. Upon the addition of Cu²⁺ to the solution of the molecule, it displayed an obvious fluorescence quenching in a linear fashion due to the formation of a 1:1 metal–ligand complex. This fluorescent sensor exhibited a rare sensitivity toward Cu(II) (the level of magnitude could be 6?×?10^?8), a rapid response (<10 s) and also high selectivity toward Cu²⁺ over other metal ions such as Na⁺, K⁺, Ca²⁺, Mg²⁺, Ba²⁺, Fe³⁺, Mn²⁺, Hg²⁺, Pb²⁺, Cd²⁺, Cr³⁺, Co²⁺, Zn²⁺ and Al³⁺. Simultaneously, the cell imaging experiments and filter paper test demonstrated its extensive applicability.     

Graphene-based passively Q-switched Nd:KLu(WO4)2 eye-safe laser operating at 1,425 nm

With graphene as saturable absorber, an Nd:KLu(WO₄)₂ eye-safe laser operating at 1,425 nm is demonstrated. To the best of our knowledge, this is the first demonstration that an Nd:KLu(WO₄)₂ laser operates at the eye-safe 1.4-μm region. A maximum total average output power of 170 mW is obtained under the pump power of 9.6 W, corresponding to an optical–optical efficiency of 1.77 %. The minimum pulse width and the highest pulse repetition rate are 153 ns and 97 kHz, respectively. Also the characteristics of the graphene used as saturable absorber for a 1.4-μm laser were studied for the first time.     

Study of a millimeter-wave squint indirect holographic algorithm suitable for imaging with large field-of-view

In this paper a millimeter-wave （MMW） squint indirect holographic method is presented, which is suitable for imaging with a large field-of-view. The proposed system employs the squint operation mode to remove the background and twin- image interferences, which achieves a similar effect to off-axis holography but leaves out the large-aperture quasi-optical component. The translational scanning manner enables a large field of view and ensures the image uniformity, which is difficult to realize in off-axis holography. In addition, a corresponding imaging algorithm for the presented scheme is developed to reconstruct the image from the recorded hologram. Some imaging results on typical objects, obtained with electromagnetic simulation, demonstrate good performance of the imaging scheme and validate the effectiveness of the image reconstruction algorithm.     

湿颗粒堆力学特性的离散元法模拟研究

利用基于线性黏聚接触模型的离散元法对不同颗粒系统的堆积过程进行了数值模拟研究,分析了颗粒形状和湿颗粒间液桥力对颗粒堆积形态的影响机理,获得了球形和块状湿颗粒堆基底表面所受的法向力以及堆中颗粒间的法向力和切向力"中心凹陷"式的分布规律,讨论了颗粒形状和黏聚能量密度对基底表面作用力和颗粒间作用力的影响.研究结果表明,颗粒形状和液桥力对颗粒堆的堆积形态具有显著的影响.堆积角随着黏聚能量密度的增加而增大,并且相同条件下的块状颗粒堆积角大于球形颗粒.颗粒形状和黏聚能量密度对基底表面所受作用力和堆中颗粒间的作用力变化及最大幅值均有影响作用.当黏聚能量密度值逐渐增大时,颗粒堆的作用力最大幅值均逐渐增大,并且块状颗粒堆的作用力最大幅值大于球形颗粒堆.当黏聚能量密度值过大时,颗粒堆力学特性更加复杂,液桥力对颗粒堆积特性的影响作用大于颗粒形状的影响.     

高温超导电缆直流测试电源平台的搭建

根据高温超导电缆测试用直流电源平台的要求,建立了硬件平台。该平台为模块化结构,具有输出精度高,便于扩展等特点;为方便操作,建立了基于LabVIEW的软件平台,对直流电源平台进行远程控制,并给出了远程控制的程序流程图,实现了电流的匀速上升和下降以及上升过程中的中断操作;利用该电源平台进行了超导电缆的临界电流测试实验,验证了直流电源平台符合高温超导电缆的测试要求。     

Efficient Fluorescent Recognition of Carboxylates in Aqueous Media Using Facilely Electrosynthesized Poly(9-Aminofluorene)

A variety of carboxylates were recognized using poly(9-aminofluorene) (P9AF) in the HEPES buffer (pH 7.4), and a proposed possible mechanism was proposed as following. The intermolecular hydrogen bonding interactions resulted in electron transfer between P9AF and carboxylates. P9AF was facilely electrosynthesized in boron trifluoride diethyl etherate and could be used as an efficient fluorescent sensing material for the detection of AcO^?. On binding to AcO^?, fluorescence quenching of P9AF was demonstrated by a maximum 80 % reduction in the fluorescence intensity, while no obvious fluorescence change could be observed in the presence of some other common anions. Some different carboxylates could be recognized at different levels by P9AF. Substituent groups in carboxylates could affect the intermolecular interaction between carboxylates and P9AF. These could be explained by a possible mechanism that hydrogen bonding was the main way of intermolecular interactions between P9AF and carboxylates, which was further confirmed by absorption spectra monitoring and density functional calculations. The significant advantage of this strategy is that it does not require a prequenching procedure and the polymer can be used directly for analyte detection.     

激光喷丸改善TC6钛合金组织和力学性能

为了使激光冲击强化技术能较好地应用于TC6钛合金的发动机叶片,对TC6钛合金进行试验研究。通过X射线衍射仪、透射电子显微镜等测试技术分析了不同参数下TC6钛合金的微观组织变化,用显微硬度计和残余应力测试仪分别表征表层硬度和残余应力变化,并测试材料冲击后的振动高周疲劳性能。试验结果表明:激光冲击材料后表面组织得到明显细化,随着冲击次数的增加,先后出现了高密度位错、位错胞、亚晶和纳米晶。性能方面,表面硬度在冲击一次即可提高19%,硬度影响深度达到700 m;与此同时表面残余应力最高达到-608.5 MPa,在500 m深度上仍具有-100 MPa左右的应力存在。经三次冲击后,标准疲劳试片的疲劳极限提高近20%。