热压制备(AgSbTe2)100-x-(GeTe)x合金的热电性能

以Pb粉、Te粉、Ag粉、Ge粉为原材料,在真空气氛下合成(AgSbTe₂)_100-x-(GeTe)_x (x=80---90) (TAGS)合金热电材料, X射线衍射(XRD)分析表明,热压烧结后合金具有低温菱形结构. 通过热压烧结法将TAGS粉末制备成块体材料,运用XRD和扫描电子显微镜对材料的物相成分、 晶体结构和形貌进行了表征.采用直流四探针法测定样品的电导率,当样品两端的温差为1---4℃ 的情况下测量Seebeck系数.通过材料热电性能测试,研究了30---500℃温度范围内不同组分 样品性能参数的变化.结果表明,所制备的TAGS热电材料具有纳米结构, 其性能随着组分的变化而变化, TAGS-80具有较好的热电性能,在530℃时具有最高热电优值(ZT=1.80).     

碳纤维复合材料内部缺陷深度的定量红外检测

利用脉冲红外热成像技术对碳纤维复合材料试件内部的模拟脱黏缺陷的深度进行测量, 研究在被测物热属性参数未知情况下,碳纤维增强塑料中缺陷深度的测量方法. 分析了平板材料在脉冲热源激励下的一维热传导模型;给出了内部缺陷深度的红外测量原理; 选用对数温度二阶微分峰值时刻作为特征时间测量缺陷深度; 考虑单点标定测量深度可能产生较大的随机误差,提出利用最小二乘法多项式拟合建立阶梯件中阶梯深度与其对应的对数温度时间二阶微分曲线峰值时间两者之间的标定关系式的方法, 选择在相对误差平方和最小情形下的拟合关系式作为脱黏缺陷深度测量的标定关系式. 实验结果表明,利用该方法测量脱黏缺陷深度的精度优于单点法标定测量结果, 实现了在被检测材料热属性参数未知的情况下仍能较准确地测量脱黏缺陷深度.     

A wide dynamic range laser rangefinder with cm-level resolution based on AGC amplifier structure

A pulsed time-of-flight (TOF) laser rangefinder with a pulsed laser diode and an avalanche photo diode (APD) receiver is constructed and tested. Trigged by an avalanche transistor, the laser diode can emit a periodic pulse with rise time of ～2 ns. A new structure with auto gain control (AGC) circuits both in the pre-amplifier and the post-amplifier is presented. Through this technology, not only the dynamic range of the receiver is extended, but also the walk error of timing discriminators is reduced. Large measurement range from 5 m to 500 m is achieved without any cooperative target. The single-shot precision is 3 cm for the weakest signal. Compared with previous laser rangefinders, the complexity of this system is greatly simplified.     

Laser diode pumped LNYAB self-frequency-doubling lasers

The LNYAB self-doubling laser pumped by (LD) has been developed for the first time. The properties of the lasers are much better than those of NYAB self-doubling lasers pumped by LD. The LNYAB self-doubling laser pumped by LD can be operated in TEM_(00) mode with threshold pumping power of 3.6mW which is lower than that of LD pumped NYAB self-doubling lasers by 74%. The output power is 29mW at 0.531μm in green region with optical-to-optical efficiency of 4.8% which is higher than that of NYAB self-doubling laser by 20%.     

A five-channel grating spectrometer for millimeter-waves

A five-channel grating spectrometer for use in millimeter wave band (25100GHz) is described with its design theory of optical path, and measured results of insertion loss and resolving power.     

飞行试验大数据技术及展望

现代航空武器装备综合化和信息化程度越来越高,飞行试验测试数据的种类增多,测试数据量剧增,飞行试验进入了大数据时代。试飞大数据的来临,对试验数据的获取、记录、传输和处理等传统技术及模式产生了强大的冲击,也提出了严峻的挑战。本文在简要介绍大数据概念及国外研究应用现状的基础上,通过总结分析飞行试验数据的新特征、新需求,提出了“试飞大数据”的概念,得出飞行试验数据是典型大数据的结论;按照试飞测试流程和大数据技术范畴,重点分析了试飞大数据技术中的数据获取、交换、记录、传输、监控、处理、存储等关键技术,最后,对试飞大数据技术的应用前景进行了展望。     

电磁波在大面积等离子体片中传播特性的分析

脉冲磁约束线形空心阴极放电形成的大面积等离子体片可应用于等离子体天线、隐身及模拟超音速飞行器表面的等离子体鞘套. 本文首次利用实测等离子体片电子密度时空分布和横向场传播矩阵法, 研究了电磁波在等离子体片中反射率、透射率、吸收率随频率及脉冲放电时间的变化特征. 结果表明: 极化方向平行磁场的电磁波, 在小于截止频率的低频带内具有较高的反射率和吸收率, 增大电流, 反射率增加, 吸收率下降, 在大于截止频率的高频带内反射率和吸收率较低, 增大电流, 透射率下降, 吸收率升高; 极化方向垂直磁场的电磁波在高混杂谐振频率附近存在吸收率明显增强的吸收带, 谐振吸收峰值与放电电流无关; 脉冲放电期间, 电磁波的反射率、透射率与吸收率由不稳定过渡到稳定的时间约为100 μs, 过渡时间随着放电电流的增加而增大, 极化方向垂直磁场、小于截止频率的电磁波在稳定放电阶段谐振吸收较强. 本文的研究成果对利用等离子体片实现对电磁波的稳定高反射作用具有重要意义.     

Mo/Si aperiodic multilayer broadband reflective mirror for 12.5-28.5-nm wavelength range

Aperiodic molybdenum/silicon (Mo/Si) multilayer designed as a broadband reflective mirror with mean reflectivity of 10% over a wide wavelength range of 12.5-28.5 nm at incidence angle of 5° is developed using a numerical optimized method. The multilayer is prepared using direct current magnetron sputtering technology. The reflectivity is measured using synchrotron radiation. The measured mean reflectivity is 7.0% in the design wavelength range of 12.5-28.5 nm. This multilayer broadband reflective mirror can be used in extreme ultraviolet measurements and will greatly simplify the experimental arrangements.     

Microstructural evolution of AZ31 magnesium alloy subjected to sliding friction treatment

Microstructural evolution and grain refinement mechanism in AZ31 magnesium alloy subjected to sliding friction treatment were investigated by means of transmission electron microscopy. The process of grain refinement was found to involve the following stages: (I) coarse grains were divided into fine twin plates through mechanical twinning; then the twin plates were transformed to lamellae with the accumulation of residual dislocations at the twin boundaries; (II) the lamellae were separated into subgrains with increasing grain boundary misorientation and evolution of high angle boundaries into random boundaries by continuous dynamic recrystallisation (cDRX); (III) the formation of nanograins. The mechanisms for the final stage, the formation of nanograins, can be classified into three types: (i) cDRX; (ii) discontinuous dynamic recrystallisation (dDRX); (iii) a combined mechanism of prior shear-band and subsequent dDRX. Stored strain energy plays an important role in determining deformation mechanisms during plastic deformation.