CdSe和ZnO量子点的拉曼光谱研究

本文介绍了用拉曼光谱研究CdSe和ZnO两种Ⅱ Ⅳ族量子点材料的结果,对拉曼峰进行了指认。观察到的光学声子峰位的移动被认为是由量子限制效应引起。     

Effects of sodium salicylate on the febrile response and increased levels of cyclic AMP in cerebrospinal fluid during endogenous pyrogen-induced fever in rabbits

To further evaluate the causality between endogenous pyrogen (EP)-induced fever and cyclic adenosine-3',5'-monophosphate (cyclic AMP) level, the effects of sodium salicylate (SS) on the febrile response and increased levels of cyclic AMP in both cerebrospinal fluid (c.s.f.) and plasma during EP-induced fever in rabbits were observed. The results suggest that cyclic AMP is probably involved in the central mediation of EP-induced fever and that increased concentration of cyclic AMP in c.s.f. associated with EP-induced fever is not the result of temperature elevation but appears to be caused by the increased synthesis in the central nervous system. In addition it is confirmed that blood is impossibly a contributory source of increased cyclic AMP in c.s.f. during EP fever, and that SS may act subsequent to the increase in cyclic AMP.     

Structure and superconductivity in FexCu1−xBa2YCu2O7+y superconductors synthesized by high pressure

Comprehensive studies of X-ray diffraction, oxygen content, superconductivity and Mössbauer effect have been made on Fe_xCu_1−xBa₂YCu₂O_7+y superconductors (0.00≤x≤0.70) synthesized by ambient (AM) and high pressure (HP). Results indicate that all the HP-samples have tetragonal structure, smaller lattice parameter c and unit-cell volume than the AM-samples. The studies of oxygen content, and Mössbauer spectroscopy indicate that the HP-samples have higher oxygen content, carrier concentration and average valence of Fe than the AM-samples. Moreover, for the HP-samples more Fe atoms located in CuO_x chains have fivefold-oxygen coordination. These are important reasons for the enhancement of T_c in the HP-samples.     

Reciprocating sliding wear behavior of laser-clad small amplitude Mo2Ni3Si/NiSi metal silicide composite coatings

Mo₂Ni₃Si/NiSi metal silicide composite coatings with a fine microstructure consisting of Mo₂Ni₃Si primary dendrites and the interdendritic Mo₂Ni₃Si/NiSi eutectics were fabricated on austenitic stainless steel AISI 321 by laser cladding process. Small amplitude reciprocating sliding wear resistance of the coatings is evaluated as functions of normal load and slip amplitude and the wear mechanisms were discussed based on worn surface morphology observations. Results showed that the Mo₂Ni₃Si/NiSi coatings have excellent small amplitude reciprocating sliding wear resistance.     

On Super Hamiltonian Semigroups

The concept of super hamiltonian semigroup is introduced. As a result, the structure theorems obtained by A. Cherubini and A. Varisco on quasi commutative semi-groups and quasi hamiltonian semigroups respectively are extended to super hamiltonian semigroups.     

Modelling and design of a travelling-wave electro-optic modulator on InP

Based on a rigorous vectorial analysis, a fast travelling-wave Mach–Zehnder modulator is modelled and designed. The cross-section of the semiconductor layer stack and the lossy electrodes are carefully modelled using the method of lines in order to investigate propagation characteristics, velocity and losses. This yields an accurate microwave and optical field distribution to explain the behaviour of the component. In order to enhance the modulation efficiency, design curves are derived and the cross-sectional dimensions for minimum microwave loss are determined. The loss of the optimized modulator agrees very well with small-signal measurements up to 40 GHz and HFSS simulations. The layerstack of the fabricated device is suitable for integration with InP multi-wavelength lasers.     

A stable dual-wavelength fiber laser with tunable wavelength spacing using a polarization-maintaining linear cavity

We propose and experimentally demonstrate a stable dual-wavelength erbium-doped polarization-maintaining (PM) fiber laser with tunable wavelength spacing using an all-PM linear cavity that makes use of two reflection peaks from the PM fiber Bragg grating (PM-FBG). Experimental results show stable dual lasing lines with a wavelength separation of ∼0.22 nm and a large optical signal-to-noise ratio (OSNR) of over 40 dB under room temperature. By applying axial strain to the PM-FBG, the center wavelengths of the two lasing lines can be tuned over several nanometers and the wavelength separation between the lasing lines can also be tuned to as small as 0.05 nm, which, to our knowledge, is the smallest wavelength spacing ever obtained from a stable room-temperature dual-wavelength fiber laser. The proposed laser configuration has the advantages of simple structure, low loss, stable dual-wavelength operation and a very small lasing linewidth of ∼5 kHz . PACS 42.55.Wd; 42.81.-i; 42.81.Gs     

2,9-disubstituted 1,10-phenanthroline nickel complexes: Syntheses,characterization, and their ethylene oligomerization

Nickel complexes 1–4 ligated with 2,9-disubstituted-1,10-phenanthroline were synthesized and characterized by FT-IR spectra and elemental analysis. The molecular structure of complex 2 was confirmed by X-ray crystal diffraction analysis. Activated with methylaluminoxane (MAO), those complexes showed moderate activities for ethylene oligomerization. Published in Kinetika i Kataliz, 2007, Vol. 48, No. 5, pp. 710–714. This article was submitted by the authors in English.     

Multi-layer thin films/substrate system subjected to non-uniform misfit strains

Current methodologies used for the inference of thin film stress through curvature measurement are strictly restricted to stress and curvature states that are assumed to remain uniform over the entire film/substrate system. These methodologies have recently been extended to a single layer of thin film deposited on a substrate subjected to the non-uniform misfit strain in the thin film. Such methodologies are further extended to multi-layer thin films deposited on a substrate in the present study. Each thin film may have its own non-uniform misfit strain. We derive relations between the stresses in each thin film and the change of system curvatures due to the deposition of each thin film. The interface shear stresses between the adjacent films and between the thin film and the substrate are also obtained from the system curvatures. This provides the basis for the experimental determination of thin film stresses in multi-layer thin films on a substrate.