Capabilities and limits of ICP-MS for direct determination of element traces in saline solutions

An ICP-MS method for the determination of ultra-traces of 24 Elements (Li, Be, Mg, Al, Cr, Mn, Co, Zn, Cu, Ga, As, Se, Rb, Sr, Mo, Ag, Cd, Sn, Sb, Ba, Tl, Pb, Bi, U) at ng/L to μg/L levels in highly saline solutions (up to 30 g/L NaCl) was developed. Calculated to the salt content of the samples, limits of detection at the sub-μg/kg level were obtained. This allows the measurement of samples like sea water, or clinical samples like urine, serum and whole blood, with few or without sample preparation and a drastic improvement to the limits of detection. Compared to the determination in solutions of 1 g/L NaCl the limits of detection in the original sample were improved by one order of magnitude. Improvements in instrumental stability are achieved by the use of an additional gas, that is introduced to the aerosol stream and avoids salt deposition in the aerosol tube of the torch, the use of High Matrix Content (HMC) cones, that show no clogging even at NaCl-concentrations up to 50 g/L. With this setup the long term stability for measurements with changing matrix concentrations is < 10% without and < 5% with use of an internal standard for the individual samples. Cleaning up is necessary after 2 days of operation. The direct analysis of the Nearshore Seawater Reference Material NRC-CNRC CASS3 showed a good agreement with the certified and measured concentrations. Elements, that do not suffer from an isobaric overlap of matrix compounds can be determined clearly at ng/L levels. Measurement of different matrix concentrations showed, that acceptable results can be achieved with a single calibration for concentrations from 5 g/L NaCl to 30 g/L NaCl, though matrix matching shows the best results.     

New AlDy(Ni,Co) glasses - the influence of pre-aging on decomposition and modelling of the crystallisation

The decomposition of AlDy₆Ni₁₀ and AlDy₈Ni₆Co₂ glasses prepared by melt spinning after different pre-aging regimes was investigated. The modelling of the transformation at the glass transition and the crystallisation was tested by a more general Johnson-Mehl-Avrami-Kolmogorov model and by the determination of the local kinetic parameter. The relaxation was tested with an lnt kinetic model after Gibbs.     

A new formula for the saddle-to-scission time

We propose a new formula for the saddle-to-scission time that is more general that the one based on Kramers' approach. Its validity and applicability is then studied in detail. Such a formula is useful for the evaluation of the fission time of very heavy nuclei.     

III-V compound semiconductor (001) surfaces

There has been renewed interest in the structure of III-V compound semiconductor (001) surfaces caused by recent experimental and theoretical findings, which indicate that geometries different from the seemingly well-established dimer models describe the surface ground state for specific preparation conditions. I review briefly the structure information available on the (001) surfaces of GaP, InP, GaAs and InAs. These data are complemented with first-principles total-energy calculations. The calculated surface phase diagrams are used to explain the experimental data and reveal that the stability of specific surface structures depends largely on the relative size of the surface constituents. Several structural models for the Ga-rich GaAs (001)(4×6) surface are discussed, but dismissed on energetic grounds. I discuss in some detail the electronic properties of the recently proposed cation-rich GaAs (001)ζ(4×2) geometry. Received: 18 May 2001 / Revised version: 23 July 2001 / Published online: 3 April 2002     

Isotopic production cross sections of residues in reactions induced by relativistic heavy ions with protons and deuterons

The isotopic production cross sections of heavy residues in relativistic heavy-ion collisions have been investigated in inverse kinematics. The primary reaction products were fully identified in mass and atomic number prior to beta decay using the fragment separator FRS. The huge collection of data obtained helps in the understanding of the two main reaction mechanisms involved: fragmentation and fission. These data provide basic information for future radioactive ion beam facilities and for technical applications like intense neutron sources by means of spallation targets.     

Synthesis and characterization of a semiflexible liquid crystalline polyester with a broad nematic region

In this paper, we report on the synthesis and detailed characterization of a new semiflexible nematic liquid crystalline polyester which could serve as a 'model' polyester for a variety of physical and physico-chemical investigations. The polymer is a nematic liquid over a wide temperature range-from the glass transition temperature at ∼95°C to the isotropic transition at ∼240°C. We expect this polyester to be particularly useful for studying the effect of flow on the orientation of liquid crystalline polymers, as well as the production and removal of disclinations.     

Behavior of iodododecane in nuclear fuel reprocessing

By simulation experiments with a 10^–5 mol/l solution of iodododecane labeled with¹³¹I in n-dodecane the influence of various materials and conditions, which are possible in nuclear fuel reprocessing, has been investigated. The formation of decomposition products was detected via HPLC with a radioactivity monitor. By means of²⁵²Cf plasma-desorption mass spectrometry (PDMS) the decomposition products were identified. It was found that a temperature of 100°C favored the formation of iodoalkanes with chain lengths of C₁ to C₁₁. The presence of TBP(tri-n-butyl-phosphate) accelerated the decomposition of iodododecane. In pure TBP only iodobutane was formed as a decomposition product.