Déformations des algèbres de Lie locales et analogue du théorème d'algébricité de Carles

Sans résumé

---

     

The influence of synthetic conditions on the stability of methotrexate-monoclonal antibody conjugates determined by reversed phase high performance liquid chromatography.

Methotrexate (MTX) has been convalently attached to an IgG-type monoclonal antibody (791T/36) directed to tumour-associated antigen gp72. Conjugates were synthesized by the active ester method using MTX N-succinimidyl ester at various pH values (7.5-10.5). Following purification by gel filtration, high performance liquid chromatography was used to assess the free drug or its derivatives in samples of MTX-791T/36 conjugates previously treated (or not) with hydroxylamine. Quantitative analysis, performed on a reversed phase column (pore size 300 A) with isocratic acetonitrile-sodium acetate buffer (pH 4.8) as mobile phase, indicated no detectable amount of free methotrexate in hydroxylamine-treated conjugates even six months after their preparation. Similar observations were made with conjugates, whose synthesis were performed at pH greater than or equal to 10. In contrast, the presence of increasing amounts of drug/metabolite could be demonstrated in samples produced at lower pH values. Based on these findings, the pH-dependent kinetics of MTX release has been determined and used to design conditions under which stable MTX-791T/36 conjugates could be prepared without hydroxylamine reaction.     

A semi-analytic meshfree method for Almansi–Michell problems of piezoelectric cylinders

Saint-Venant’s Problem, Almansi–Michell Problems, Meshfree Methods, Piezoelectricity. We present a semi-analytical method for analyzing prismatic nonhomogeneous piezoelectric cylinders with arbitrary cross-sectional geometry. The prescribed loads considered in this study include axial forces, torques, moments, and voltage resultants prescribed at the cylinder’s ends, as well as body forces, lateral surface shears, voltages, and pressures as long as they can be represented by a power series in the axial coordinate. This problem can be considered as an extension of Saint-Venant and Almansi–Michell problems for elastic bodies to piezoelectric bodies. In this computationally efficient method, the cross-sectional plane is discretized with a meshfree approach, and the solution is obtained analytically with respect to the axial coordinate. A number of examples are provided to demonstrate the veracity and utility of the proposed method.     

A novel method for automated grid generation of ice shapes for local‐flow analysis

Modelling a complex geometry, such as ice roughness, plays a key role for the computational flow analysis over rough surfaces. This paper presents two enhancement ideas in modelling roughness geometry for local flow analysis over an aerodynamic surface. The first enhancement is use of the leading‐edge region of an airfoil as a perturbation to the parabola surface. The reasons for using a parabola as the base geometry are: it resembles the airfoil leading edge in the vicinity of its apex and it allows the use of a lower apparent Reynolds number. The second enhancement makes use of the Fourier analysis for modelling complex ice roughness on the leading edge of airfoils. This method of modelling provides an analytical expression, which describes the roughness geometry and the corresponding derivatives. The factors affecting the performance of the Fourier analysis were also investigated. It was shown that the number of sine–cosine terms and the number of control points are of importance. Finally, these enhancements are incorporated into an automated grid generation method over the airfoil ice accretion surface. The validations for both enhancements demonstrate that they can improve the current capability of grid generation and computational flow field analysis around airfoils with ice roughness. Copyright © 2004 John Wiley & Sons, Ltd.     

On the dynamic electromechanical loading of dielectric elastomer membranes

Dielectric elastomer actuators (DEAs) have received considerable attention recently due to large voltage-induced strains, which can be over 100%. Previously, a large deformation quasi-static model that describes the out-of-plane deformations of clamped diaphragms was derived. The numerical model results compare well with quasi-static experimental results for the same configuration. With relevance to dynamic applications, the time-varying response of initially planar dielectric elastomer membranes configured for out-of-plane deformations has not been reported until now. In this paper, an experimental investigation and analysis of the dynamic response of a dielectric elastomer membrane is reported. The experiments were conducted with prestretched DEAs fabricated from 0.5 mm thick polyacrylate films and carbon grease electrodes. The experiments covered the electromechanical spectrum by investigating membrane response due to (i) a time-varying voltage input and (ii) a time-varying pressure input, resulting in a combined electromechanical loading state in both cases. For the time-varying voltage experiments, the membrane had a prestretch of three and was passively inflated to various predetermined states, and then actuated. The pole strains incurred during the inflation were as high as 25.6%, corresponding to slightly less than a hemispherical state. On actuation, the membrane would inflate further, causing a maximum additional strain of 9.5%. For the time-varying pressure experiments, the prestretched membrane was inflated and deflated mechanically while a constant voltage was applied. The membrane was cycled between various predetermined inflation states, the largest of which was nearly hemispherical, which with an applied constant voltage of 3 kV corresponded to a maximum polar strain of 28%. The results from these experiments reveal that the response of the membrane is a departure from the classical dynamic response of continuum membrane structures. The dynamic response of the membrane is that of a damped system with specific deformation shapes reminiscent of the classical membrane mode shapes but without same-phase oscillation, that is to say all parts of the system do not pass through the equilibrium configuration at the same time. Of particular interest is the ability to excite these deformations through a varying electrical load at constant mechanical pressure.     

Weak Attractive Ligand–Polymer and Related Interactions in Catalysis and Reactivity: Impact,Applications, and Modeling

The notion of weak attractive ligand–polymer interactions is introduced, and its potential application, importance, and conceptual links with “cooperative” ligand–substrate interactions are discussed. Synthetic models of weak attractive ligand–polymer interactions are described, in which intramolecular weak C? H???F? C interactions (the existence of which remains contentious) have been detected by NMR spectroscopy and neutron and X‐ray diffraction experiments. These C? H???F? C interactions carry important implications for the design of catalysts for olefin polymerization, because they provide support for the practical feasibility of ortho‐F???H_β ligand–polymer contacts proposed for living Group 4 fluorinated phenoxyimine catalysts. The notion of weak attractive noncovalent interactions between an “active” ligand and the growing polymer chain is a novel concept in polyolefin catalysis.     

Globally anisotropic high porosity silica aerogels

We discuss two methods by which high porosity silica aerogels can be engineered to exhibit global anisotropy. First, anisotropy can be introduced with axial strain (i.e. axial compression). In addition, intrinsic anisotropy can result during growth and drying stages and, suitably controlled, it can be correlated with preferential radial shrinkage in cylindrical samples. We have performed small angle X-ray scattering (SAXS) to characterize these two types of anisotropy. We show that global anisotropy originating from either strain or shrinkage leads to optical birefringence and that optical cross-polarization studies are a useful characterization of the uniformity of the imposed global anisotropy.