Preparation of bisdiazoalkane and related complexes from the reactions of diazo compounds with the dinitrogen complexestrans-[M(N2)2(Ph 2PCH2CH2PPh 2)2] (M=Mo or W)

Summary Reactions oftrans-[M(N₂)₂(dppe)₂] (A;M=Mo, W;dppe=Ph ₂PCH₂CH₂PPh ₂) with ethyldiazoacetate, N₂CHCOOEt, yield the bisdiazoalkane speciestrans-[M(N₂CHCOOEt)₂(dppe)₂], upon simple replacement of the dinitrogen ligand by ethyldiazoacetate. However, diazomethane, N₂CH₂, reacts withA with loss of N₂ to give products which we tentatively formulate as containing methylene ligands,trans-[M(CH₂)₂(dppe)₂].

---

Herstellung von Bisdiazoalkan- und ähnlichen Komplexen aus den Reaktionen von Diazoverbindungen mit Distickstoffkomplexen des Typstrans-[M(N₂)₂(Ph ₂PCH₂CH₂PPh ₂)₂] mitM=Mo oder W

Zusammenfassung Die Reaktion vontrans-[M(N₂)₂(dppe)₂] (A:dppe=Ph ₂PCH₂CH₂PPh ₂ undM=Mo oder W) mit Ethyldiazoacetat, N₂CHCOOEt, ergab nach einfachem Austausch des Distickstoffliganden mit Ethyldiazoacetat die Bisdiazoalkanetrans-[M(N₂CHCOOEt)₂(dppe)₂]. Diazomethan (N₂CH₂) hingegen reagierte mitA unter Verlust von N₂ zu Produkten, die tentativ alstrans-[M(CH₂)₂(dppe)₂] mit Methylenliganden formuliert wurden.

     

Pyrolysis-mass spectrometry correlations of crosslink density in natural rubber vulcanizates

A set of twelve natural rubber vulcanizates was analyzed by Curie-point pyrolysis-mass spectrometry (Py-MS). Multivariate analysis successfully correlated the Py-MS data with either total or polysulfidic crosslink density measurements. (Polysulfidic means two or more sulfurs.) The principal correlation observed was an increase in the ratio of monomer to dimer pyrolyzate yield with an increase in crosslink density. The feasibility of using Py-MS for total crosslink density determination has thus been demonstrated. The Py-MS data, however, did not allow us to distinguish different types of crosslinks.     

The electronic properties of isocyanides at rhenium—dinitrogen binding sites. Preparation and redox properties of the isocyanide complexes trans-[ReCl(CNR)(Ph2PCH2CH2PPh2)2]

The isocyanide complexes trans-[ReCl(CNR)(dppe)₂] (R  Me, Bu^t, C₆H₄CH₃-4, C₆H₄CH₃-2, C₆H₄Cl-4, C₆H₄OCH₃-4 and C₆H₃Cl₂-2,6; dppe  Ph₂PCH₂CH₂PPh₂) have been prepared by isocyanide displacement of dinitrogen from the parent complex trans-[ReCl(N₂)(ddpe)₂]. Their redox properties have been studied by cyclic voltammetry and are interpreted on the basis of the electronic properties and the geometry of the ligating isocyanides which are believed to be bent in these complexes, appearing to exhibit ligand parameter (P_L) values ca. +0.3 V higher than those which would be expected for linear geometry. A very high polarisability (B ? 3.4) is observed for the {ReCl(dppe)₂} site.     

Electrochemical detection of tryptophan metabolites following high-performance liquid chromatography.

Electrochemical detection of tryptophan metabolites following separation on a reversed-phase high-performance liquid chromatography column was compared with other means of detection. Of 29 compounds studied, 26 could be detected at a sensitivity comparable to that of fluorescence derivatisation procedures. Response was linear over a wide range of concentrations and selectivity was shown to be superior to ultraviolet detection when analysing urine. Additionally, it was possible to control selectivity so that only those tryptophan metabolites from the tryptophan hydroxylase pathway were detected. This is of particular value in the study of distrubances of serotonin metabolism and is unique to this type of detector.     

Molecular weights of backbones in graft copolymers

Copolymerization of a monomer X with an existing polymer yields a copolymer contaminated by poly-X homopolymer and ungrafted polymer. Measurements on the pure copolymer can yield only the molecular weights of the cumulative backbone portion and of the cumulative graft portion. However, if the grafts can be isolated, then the molecular weights of their individual chains may be determined also. Since it is not isolatable, the backbone is not amenable to similar treatment. Equations are derived for the molecular weights (of any average) of individual backbone chains; they are expressed in terms of the following experimentally accessible quantities: (i) molecular weight of original polymer; (ii) molecular weight of ungrafted portion: and (iii) fraction by weight of the original polymer which remains ungrafted. The procedure is thus the analogue, applied to the backbone, of chemical isolation applied to the grafts. The treatment has been examined for copolymers prepared by grafting acrylic acid to nylon-6 by mutual irradiation.     

Multiple nitrene insertions into metal-sulfur bonds of dithiocarbamate complexes: synthesis of sulfido-amido and zwitterionic tetraamido complexes

The iodine(III) reagent, PhI[double bond, length as m-dash]NTs, acts as a source of the nitrene fragment NTs, which undergoes facile insertion into the metal-sulfur bonds of a range of dithiocarbamate complexes. Addition of two equivalents of PhI=NTs to [M(S(2)CNR2)2] affords sulfido-amido complexes [M{SC(NR2)SNTs}2](M=Ni, Cu), which insert two further nitrene fragments to afford zwitterionic tetraamido complexes [M{TsNSC(NR2)SNTs}2](M=Co, Ni, Cu). Crystallographic studies have been carried out on both types of complex allowing possible resonance hydrids of the new ligand types to be assessed.     

Generation of 3-pyridyl biaryl systems via palladium-catalyzed Suzuki cross-couplings of aryl halides with 3-pyridylboroxin

The synthesis of 3-pyridyl biaryl systems can be readily achieved by means of palladium-catalyzed Suzuki cross-coupling reactions between aryl halides and 3-pyridylboroxin. A series of cross-couplings were conducted in order to investigate the scope and limitations of this protocol.     

A ferrocene based palladacyclic precatalyst for the Suzuki cross-coupling of aryl chlorides

Addition of palladium acetate to 2-(dicyclohexylphosphino)-phenylferrocene gave palladacycle 16 that is a very effective precatalyst for the Suzuki cross-coupling of aryl chlorides at room temperature (1 mol% 16) or 60 degrees C (> or = 0.01 mol% 16).