Permeability of dye through poly(urea-urethane) microcapsule membrane prepared from mixtures of di- and tri-isocyanate

Poly(urea-urethane) microcapsules were prepared by the interfacial polymerization with using mixtures of tri- and di-isocyanate monomers as wall forming materials, and dioctyl phthalate containing an oil-soluble dye as a core material. The time course of the dye release in dispersing tetrahydrofuran was measured as a function of the weight fraction of tri-isocyanate monomer in the total monomer w and the core/wall material-weight ratio g. The dye release curves were well represented by an exponential function C=Ceq(1-e-t/tau), where C is the concentration of the dye in the dispersing medium, Ceq that at equilibrium state, t the elution time and tau is a time constant. tau increased linearly against w at high g, suggesting controllability of the release rate of microcapsules by varying tri-isocyanate/di-isocyanate ratio.     

Determination of bovine blood oleandrin by high-performance liquid chromatography and postcolumn derivatization

A high-performance liquid chromatographic procedure with a postcolumn fluorescence derivatization is developed for the analysis of oleandrin in bovine blood. Oleandrin is separated by an octadecylsilane-bonded column with a mobile phase containing dehydroascorbic acid. The effluent of the column is mixed with concentrated hydrochloric acid and passed through poly(tetrafluoroethylene) tubing maintained at 70 degrees C. The resultant fluorophores are detected at 465 nm with excitation at 348 nm. Simple solid-phase extraction using Sep-Pak tC2 is effective for sample purification. We found the minimal detectable quantity of oleandrin in plasma to be 1.5 ng/mL at a signal-to-noise ratio of 3:1.     

The electronic structure of low-lying excited states of two model systems of retinal

2,4-pentadienal and 2,4,6,8-nonatetraenal were studied as simple model systems of retinal. Four kinds of CI were performed on low-lying excited states of 2,4-pentadienal by using a split valence basis set. The results show that MR SD π CI is not adequate for the π–π* state and the single excitation σπ CI is a good compromise between cost and effectiveness as far as singly excited states are concerned. This CI was applied to the bigger model system. All-trans and 11-cis forms of aldehyde, Schiff base, and protonated Schiff base of the model system were studied. A fairly large energy lowering of about 1 eV of the first allowed excited state (π → π*) occurs when the Schiff base is protonated for both all-trans and 11-cis forms.     

Migration to Broadband and Ubiquitous Environments by Using Fiber-Optic Technologies in Access/Home Areas

ABSTRACT

The recent dramatic advances in information and communication technologies have yielded new environments. However, adoption still differs area by area. To realize the future broadband environment that everyone can enjoy everywhere, several technical issues have to be resolved before network penetration becomes ubiquitous. One such key is the use of fiber optics for the home and mobile services. This article overviews initial observations drawn from numerical survey data gathered over the last decade in several countries/regions, and gives some example scenarios for network/service evolution. One result implies that implementing new/future services must consider the gross domestic product impact.     

Surface modification of polydimethylsiloxane with photo-grafted poly(ethylene glycol) for micropatterned protein adsorption and cell adhesion

In this study, we applied photo-induced graft polymerization to micropatterned surface modification of polydimethylsiloxane (PDMS) with poly(ethylene glycol). Two types of monomers, polyethylene glycol monoacrylate (PEGMA) and polyethylene glycol diacrylate (PEGDA), were tested for surface modification of PDMS. Changes in the surface hydrophilicity and surface element composition were characterized by contact angle measurement and electron spectroscopy for chemical analysis. The PEGMA-grafted PDMS surfaces gradually lost their hydrophilicity within two weeks. In contrast, the PEGDA-grafted PDMS surface maintained stable hydrophilic characteristics for more than two months. Micropatterned protein adsorption and micropatterned cell adhesion were successfully demonstrated using PEGDA-micropatterned PDMS surfaces, which were prepared by photo-induced graft polymerization using photomasks. The PEGDA-grafted PDMS exhibited useful characteristics for microfluidic devices (e.g. hydrophilicity, low protein adsorption, and low cell attachment). The technique presented in this study will be useful for surface modification of various research tools and devices.     

Biochemical sniffer with choline oxidase for measurement of choline vapour

An enzyme-based gas sensor (bio-sniffer) for choline vapour was fabricated and tested. The bio-sniffer was constructed using a Clark-type dissolved oxygen electrode and an enzyme (choline oxidase) immobilized membrane. This bioelectronic device measures choline concentration by the oxygen consumption induced by an enzyme reaction of choline oxidase. As the assessment of sensor performances, the calibration curves for choline in the liquid and gas phases were investigated, respectively. The responses of the bioelectronic device to choline solutions of various concentrations were related within a range from 5.00 to 700 μmol·L⁻¹ with a correlation coefficient of 0.999. On the other hand, the bio-sniffer for choline vapour was placed into a gas-measuring chamber and calibrated using gas detection tubes. The calibration range was 1.00–30.0 ppm (correlation coefficient: 0.996). The response time for choline vapour was approximately 15% slower than that of biosensor for choline solution. These results indicate that the bio-sniffer is useful to monitor colourless and odourless choline gas released from coating compositions including choline. Correspondence: Kohji Mitsubayashi, Department of Biomedical Devices and Instrumentation, Institute of Biomaterials and Bioengineering, Tokyo Medical and Dental University, 2-3-10 Kanda-Surugadai, Chiyoda-ku, Tokyo 101-0062, Japan     

Microphase‐separated structure of 1,3‐cyclohexadiene/butadiene triblock copolymers and its effect on mechanical and thermal properties

We report the effect of microphase‐separated structure on the mechanical and thermal properties of several poly(1,3‐cyclohexadiene‐block‐butadiene‐block‐1,3‐cyclohexadiene) triblock copolymers (PCHD‐block‐PBd‐block‐PCHD) and of their hydrogenated derivatives: poly(cyclohexene‐block‐ethylene/butylene‐block‐cyclohexene) triblock copolymers (PCHE‐block‐PEB‐block‐PCHE). Both mechanical strength and heat‐resistant temperature (ex. Vicat Softening Temperature: VSPT) tended to increase with an increase in the 1,3‐cyclohexadiene (CHD)/butadiene ratio. On the other hand, heat resistance of the hydrogenated block copolymer was found to be higher than that of the unhydrogenated block copolymer. However, the mechanical strength was lower than those of the unhydrogenated block copolymer with the same ratio of CHD to butadiene. To clarify the relationship between the higher order structures of those block copolymers and their properties, we observed the microphase‐separated structure by transmission electron microscope (TEM). Hydrogenated block copolymers were found to have more finely dispersed microphase‐separated structures than those of the unhydrogenated block copolymers with the same CHD/Bd ratios through the use of TEM and the small‐angle X‐ray scattering (SAXS) technique. Those results indicated that the segregation strength between the PCHE block sequence and the PEB block sequence increased, depending on hydrogenation of the unhydrogenated precursor. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 13–22, 2001     

Synthesis of novel hydrocarbon polymers containing 6‐membered rings in the main chain: living anionic polymerization of 1,3‐cyclohexadiene

The n‐butyllithium (n‐BuLi)/N,N,N',N'‐tetrametylethylene‐diamine (TMEDA) system (the molar ratio of TMEDA to n‐BuLi higher than 4/4) has been found to polymerize 1,3‐cyclohexadiene (1,3‐CHD) to produce “living” polymer having narrow molecular weight distribution with well‐controlled polymer chain length. Binary and ternary block copolymers with narrow molecular weight distribution could be synthesized from 1,3‐cyclohexadiene, styrene, and butadiene with very high efficiency. These polymers and their hydrogenated derivatives have excellent thermal, mechanical, chemical, and optical properties for the new industrial materials.     

Intramolecular hydrosilation of acetylenes: Regioselective functionalization of homopropargyl alcohols

Platinum-catalyzed intramolecular hydrosilation of hydrodimethylsilyl ethers of homopropargyl alcohols proceeds regioselectively in a 5-exo-dig mode. The resulting vinylsilanes can be transformed into 3-alkanon-1-ol and 3-bromo-3-alken-1-ol derivatives by H₂O₂ oxidation and bromine cleavage, respectively.     

The First Heterotriquinone and Dicyanoheterotriquinone Methide That Undergo a Five-Stage Amphoteric Redox Reaction

The dicyanomethylene group and not the quinone oxygen atoms is the site of the first one-electron reduction for the dicyanohetereotriquinone methide 1 , although the dicyanomethylene group is substituted at a cyclopentadienyl-like five-membered ring! Compound 1 is amphoteric and undergoes a five-stage sequence of one-electron redox reactions.