Alloying by high dose ion implantation of iron into magnesium and aluminium

Alloys of the systems Fe–Al (mixable over the whole concentration range) and Fe–Mg (insoluble with each other) were produced by implantation of Fe ions into Al and Mg, respectively. The implantation energy was 200 keV and the ion doses ranged from 1 × 10₁₄ to 9 × 10₁₇cm^-2The obtained implantation profiles were determined by Auger electron spectroscopy depth profiling. Maximum iron concentrations reached were up to 60 at.% for implantation into Al and 94 at.% for implantation into Mg. Phase analysis of the implanted layers was performed by conversion electron Mössbauer spectroscopy and X‐ray diffraction. For implantation into Mg, two different kinds of Mössbauer spectra were obtained: at low doses paramagnetic doublets indicating at least two different iron sites and at high doses a dominant ferromagnetic six‐line‐pattern with a small paramagnetic fraction. The X‐ray diffraction pattern concluded that in the latter case a dilated αiron lattice is formed. For implantation into Al, the Mössbauer spectra were doublet structures very similar to those obtained at amorphous Fe–Al alloys produced by rapid quenching methods. They also indicated at least two different main iron environments. For the highest implanted sample a ferromagnetic six‐line‐pattern with magnetic field values close to those of Fe₃Al appeared.     

State of and prospects for XeF(C−A) optically pumped lasers

Experimental and theoretical results are presented on an XeF(C?A) blue-green laser driven by 5-kJ energy. The laser was pumped by a ferrite-induced discharge of 90 cm in length. The output energy of 0.22 J was obtained with a plane-parallel resonator. A program to simulate laser operation has been developed. Numerical results for a wide range of conditions are compared with experiments performed by us and by other authors. It is found that intracavity refractive losses limit laser operation for XeF pressures above 3 torr. The laser efficiency strongly depends on the discharge-to-cavity length ratio. Possible ways to increase the laser power and efficiency are discussed.     

Three-dimensional atom probe study of the segregation behaviour of Ni91Pt9 alloy after sputtering

To investigate local ordering and segregation phenomenon in a Ni91Pt9-alloy after sputtering and annealing a 3D optical atom probe (OAP) has been used. The specimen tips have been prepared from polycrystalline samples. To sputter the samples a separate preparation chamber with a scannable Ar-sputter-gun is connected to the OAP vessel. When necessary, the sample can be electrically heated to induce segregation and cure the altered layer. After a heat treatment of a Ni91 at. %Pt 9 at.% specimen at 1100 K the surface of a (111)-oriented specimen is enriched in platinum by a factor of two in relation to the bulk. The phenomenon of short-range ordering has been investigated on the surface and in the subsurface volume. A 3D reconstruction of this annealed NiPt specimen shows regions with high concentration of platinum that gives an indication at short-range ordering. Uniform sputtering of the tip without a heat treatment induces a decisive depletion of Pt on the surface and the following subatomic layers. The atom-probe results of specimens in thermal equilibrium are in close agreement to further surface sensitive results obtained from Ion Scattering Spectroscopy (ISS) and Auger Electron Spectroscopy (AES).     

Estimation of multivariate binary density using orthogonal functions

In this paper, the authors studied certain properties of the estimate of Liang and Krishnaiah (1985, J. Multivariate Anal. 16, 162–172) for multivariate binary density. An alternative shrinkage estimate is also obtained. The above results are generalized to general orthonormal systems.     

Effects of annealing conditions on the electrical properties of Bi4-xNdxTi3O12 (x = 0.46) thin films processed at low temperature

Neodymium-substituted Bi₄Ti₃O₁₂ (BNdT) thin films were prepared by a chemical solution deposition technique on platinum- coated silicon substrates. All of the samples were annealed at the relatively low temperature of 600 °C by a rapid thermal annealing process in different atmospheres, such as O₂, air, and nitrogen, and vacuum. Irrespective of different annealing atmospheres, all of the BNdT thin films exhibit good ferroelectric properties, such as a saturated hysteresis loop, good fatigue endurance, and low leakage current density. A large remanent polarization (P_r) of ∼48 μC/cm² with an electric field of 240 kV/cm was observed from the BNdT thin film annealed in O₂ atmosphere. The BNdT thin films annealed in nitrogen and vacuum, at reduced oxygen partial pressures, exhibit smaller P_r than that annealed in oxygen. The difference of P_r of the BNdT thin films annealed in different atmospheres may originate from differences in the grain sizes and the number of oxygen vacancies. PACS 77.55.+f; 77.80.-e; 77.80.Fm; 81.15.-z     

Rigidity and finiteness under Ricci curvature and volume controls

Consider the class of closed Riemannian manifolds M of dimension dim(M) \geqq 3 \dim(M) \geqq 3 , Ricci curvature Ric(M) \geqq -(n - 1) \textrm{Ric}(M) \geqq -(n - 1) , diameter diam(M) < D and almost maximal volume. We show that the isomorphism types of fundamental groups characterize the diffeomorphism types of manifolds in such a class. In particular, it can be viewed as a generalization of the well-known Mostow‘s rigidity theorem and a finiteness theorem.     

Applications of coupled LC-GC: A review

Although coupled liquid chromatographygas chromatography (LC-GC) was first demonstrated ten years ago, only in the last few years has there been a sudden surge of interest in the technique. Approximately 70% of the total number of LC-GC applications have been published in the last two years (1987–88) alone. This review categorizes LC-GC publications into four main application areas: fossil fuels, foods, environmental samples, biologiical/pharmaceutical samples, and miscellaneous samples. Multidimensional separations carried out using other coupled-column chromatographic techniques (such as supercritical fluid chromatography (SFC) with GC, and on-line trace enrichment-GC) have also been included in this review.     

Development and investigation of perovskite (ABO3)-type oxides for power generation

Critical problems of the present approach of electrolytes for Solid Oxide Fuel Cells (SOFCs) for commercialization are discussed. Major progress is expected from the development of materials based on the “SEA (Single Element Arrangement)” concept. The galvanic cell consists in this case basically of a single chemically homogeneous compound, which functions as electrodes at high and low activity and as electrolyte at intermediate activities of the electroactive component. In view of the large structural flexibility of the chemical nature of the constitutents, we explored perovskite (ABO₃)-type compounds to be used as SEAs for SOFCs. Results of studies on Pr-substituted LSGM and Fe-substituted SrSnO₃ perovskite-type oxides are presented. For instance, SrSn_1-xFe_xO_3-δ with x=0.1 exhibits p and n-type electronic conduction at the cathode and anode sides of the SOFC, respectively, while oxide ion conduction prevails at intermediate oxygen partial pressures. The SEA concept is also applicable for other devices in the field of Ionics.