Force Chain Characteristics and Effects of a Dense Granular Flow System in a Third Body Interface During the Shear Dilatancy Process

In order to investigate the characteristics of force chains in a granular flow system, a parallel plate shear cell is constructed to simulate the shear movement of an infinite parallel plate and observe variations in relevant parameters. The shear dilatancy process is divided into three stages, namely, plastic strain, macroscopic failure, and granular recombination. The stickslip phenomenon is highly connected with the evolution of force chains during the shear dilatancy process. The load–distribution rate curves and patterns of the force chains are utilized to describe the load-carrying behaviors and morphologic changes of force chains separately. Force chains, namely, “diagonal gridding,” “tadpole-shaped,” and “pinnate” are defined according to the form of the force chains in the corresponding three stages.     

Logarithmic Regge pole

This work presents the subtraction procedure and the Regge cut in the logarithmic Regge pole approach. The subtraction mechanism leads to the same asymptotic behavior as previously obtained in the non-subtraction case. The Regge cut, in contrast, introduces a clear role to the non-leading contributions for the asymptotic behavior of the total cross-section. From these results, some simple parameterization is introduced to fit the experimental data for the proton-proton and antiproton-proton total cross-section above some minimum value up to the cosmic-ray. The fit parameters obtained are used to present predictions for the \begin{document}$ \rho(s)$\end{document} -parameter as well as to the elastic slope \begin{document}$ B(s)$\end{document} at high energies.     

Preparation and Insecticidal Activity of the First Organofluorine Insecticide Based on β-D-Ribofuranoside Monosaccharide

Russian Journal of General Chemistry - A method was developed for the synthesis of an organofluorine derivative of β-D-ribofuranoside. Biological tests revealed high insecticidal activity and...     

A Procedure for the Deposition of Macrocomponents in Determining Selenium and Tellurium in Metallurgical Materials by Inductively Coupled Plasma Atomic Emission Spectrometry

Journal of Analytical Chemistry - Studies on the separation of the Se and Te trace components from Co, Ni, Cu, Fe, Cr, Mo, and W macrocomponents for their determination by inductively coupled...     

A survey of surface tension,molar volume and density for Sn–Ag–Cu–Bi–Sb quinary alloys as lead-free solders

ABSTRACT

By applying the geometric models and the theoretical equation, the surface tension, the molar volume and the density were studied. The empirical calculations were carried out in temperature range 623?K?≤?T?≤?1123?K. Only few thermophysical properties were estimated for eight quinary alloys: Sn3.55Ag0.5Cu3Bi3Sb, Sn3.48Ag0.5Cu3Bi5Sb, Sn3.48 Ag0.5Cu5Bi3Sb, Sn3.40 Ag0.5Cu5Bi5Sb, Sn3.53Ag1Cu3Bi3Sb, Sn3.46Ag1Cu3Bi5Sb, Sn3.46Ag1Cu5Bi3Sb, Sn3.38Ag1Cu5Bi5Sb. The results show that surface tension and density have a linear appearance for all temperatures. We have also studied the influence of the composition and temperature in the studied alloys. The obtained theoretical results are compared with the experimental ones and with the conventional Pb–Sn welds.     

Formation of low-temperature deformation-induced segregations of nickel in Fe–Ni-based austenitic alloys

ABSTRACT

The authors present the results of an investigation in Fe–Ni-Cr austenitic alloys of the low-temperature deformation-induced segregations of nickel that form in the micro regions being (i) located close to grain- and subgrain boundaries and (ii) characteristic of the concentration and magnetic inhomogeneities indicated by the appearance of a dark diffraction contrast at the electron diffraction patterns taken from these regions typical (at the same time) of an enhanced value of Curie temperature. The observed effects were connected with the micro distortions caused by the local change of lattice parameter because of an increase in nickel concentration, as well as in the result of a magnetostriction dilatation. Using methods of the X-ray energy dispersive spectroscopy (XEDS) and atomic-probe body-section radiography (tomography – APT) has made it possible to determine the borders of those regions of austenite that were characteristic of an enhanced concentration of nickel in the fields of the localisation of a deformation-induced segregation of nickel in the vicinity of grain (subgrain) boundaries of austenitic alloys of the types Fe–13Cr–30Ni and Fe–37Ni–3Ti.