Wide‐angle X‐ray diffraction and differential scanning calorimetry study of the crystallization of poly(ethylene naphthalate), poly(butylene naphthalate), and their copolymers

The crystallization behavior of a series of poly(ethylene‐co‐butylene naphthalate) (PEBN) random copolymers was studied. Wide‐angle X‐ray diffraction (WAXD) patterns showed that the crystallization of these copolymers could occur over the entire range of compositions. This resulted in the formation of poly(ethylene naphthalate) or poly(butylene naphthalate) crystals, depending on the composition of the copolymers. Sharp diffraction peaks were observed, except for 50/50 PEBN. Eutectic behavior was also observed. This showed isodimorphic cocrystallization of the PEBN copolymers. The variation of the enthalpy of fusion of the copolymers with the composition was estimated. The isothermal and nonisothermal crystallization kinetics were studied. The crystallization rates were found to decrease as the comonomer unit content increased. The tensile properties were also measured and were found to decrease as the butylene naphthalate content of the copolymers increased. For initially amorphous specimens, orientation was proved by WAXD patterns after drawing, but no crystalline reflections were observed. However, the fast crystallization of drawn specimens occurred when they were heated above the glass‐transition temperature. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 843–860, 2004     

Bio‐based nanocomposites from functionalized plant oils and layered silicate

Some discovery work was done on the synthesis of clay nanocomposites based on renewable plant oils. Functionalized triglycerides, such as acrylated epoxidized soybean oil, maleinized acrylated epoxidized soybean oil, and soybean oil pentaerythritol maleates, combined with styrene were used as the polymer matrix. The miscibility of these monomers and clay organomodifier was assessed by solubility parameters. The formation of nanocomposites was confirmed by both X‐ray data and transmission electron microscopy. The morphology showed a mix of intercalated and partially exfoliated sheets. The flexural modulus increased 30% at only 4 vol % clay content, but there was no significant effect on flexural strength, glass‐transition temperature, and thermal stability. Property enhancement was related to the degree of exfoliation that depends on both the polarity and flexibility of the monomers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1441–1450, 2004     

Extractive spectrophotometric determination of Cobalt(II) in synthetic and pharmaceutical samples using Cyanex 923.

Cyanex 923 has been proposed as a sensitive analytical reagent for the direct extractive spectrophotometric determination of cobalt(II). Cobalt(II) forms a blue-colored complex with Cyanex 923 in the organic phase. The maximum absorbance of the complex is measured at 635 nm. Beer's law was obeyed in the range 58.9 - 589.0 microg of cobalt. The molar absorptivitiy and Sandell's sensitivity of the complex was calculated to be 6.79 x 10920 l mol(-1) cm(-1) and 0.088 microg cm(-2), respectively. The nature of the extracted species was found to be Co(SCN)2 x 2S. An excellent linearity with a correlation coefficient value of 0.999 was obtained for the Co(II)-Cyanex 923 complex. Stability and regeneration of the reagent (Cyanex 923) for reuse is the main advantage of the present method. The method was successfully applied to the determination of cobalt in synthetic mixtures and pharmaceutical samples was found to give values close to the actual ones. Standard alloy samples, such as high-speed tool BCS 484 and 485, have been tested for the determination of cobalt for the purpose of validating the present method. The results of the proposed method are comparable with atomic absorption spectrometry and were found to be in good agreement.     

Coated wire silver-ion selective electrode based on a N,N'-bis(2-thienylmethylene)-1,2-diaminobenzene.

A novel membrane coated platinum-wire electrode (MCPWE) based on N,N'-bis(2-thienylmethylene)-1,2-diaminobenzene (BTMD) for highly selective determination of Ag+ ion has been developed. The influences of membrane composition and pH on the potentiometric responses of electrode were investigated. The potentiometric responses are independent of the pH of the test solution in the range of 5.0 - 9.0. The electrode shows a linear response for Ag+ ion over the concentration range of 1.0 x 10(-60 to 1.0 x 10(-1) M with a lower detection limit of 6.0 x 10(-7) M. The electrode possesses a Nernstian slope of 59.7 mV decade(-1) and a fast response time of < or = 17 s and can be used for at least 2 months without any observable deviation. The proposed electrode displayed very good selectivity for Ag+ ion with respect to NH4+ and alkali, alkaline earth and some common transition metal ions. The practical utility of the electrode has been demonstrated by its use as the indicator electrode in the potentiometric titration of an AgNO3 solution with a NaI solution and in determination of the silver content of a developed radiological film.     

A sequential injection system for the spectrophotometric determination of calcium, magnesium and alkalinity in water samples.

A sequential injection methodology for the spectrophotometric determination of calcium, magnesium and alkalinity in water samples is proposed. A single manifold is used for the determination of the three analytes, and the same protocol sequence allows the sequential determination of calcium and magnesium (the sum corresponds to the water hardness). The determination of both metals is based on their reaction with cresolphtalein complexone; mutual interference is minimized by using 8-hydroxyquinoline for the determination of calcium and ethylene glycol-bis(beta-aminoethyl ether)-N,N,N',N'-tetraacetic acid (EGTA) for the determination of magnesium. Alkalinity determination is based on a reaction with acetic acid, and corresponding color change of Bromcresol Green. Working ranges of 0.5 - 5 mg dm(-3) for Ca, 0.5 - 10 mg dm(-3) for Mg, and 10 - 100 mg HCO3- dm(-3), for alkalinity have been achieved. The results for water samples were comparable to those of the reference methods and to a certified reference water sample. RSDs lower than 5% were obtained, a low reagent consumption and a reduced volume of effluent have been accomplished. The determination rate for calcium and magnesium is 80 h(-1), corresponding to 40 h(-1) per element, while 65 determinations of alkalinity per hour could be carried out.     

NMR investigation of concentrated alumina and silica slurries

The longitudinal relaxation times (T₁) of water in concentrated silica and alumina slurries were measured as a function of solids content. It was shown that the results could be fit very well with a two-phase fast-exchange model between free and surface-bound water. As expected, values of T₁ for bound water were in the order of 20–2000 times lower than that for free water, indicating a higher effective viscosity of the surface-bound water. The strength of the interaction depended on the particular surface, and all of the aluminas examined interacted more strongly with water than the two silicas studied, which themselves differed considerably. The chemical mechanical polishing (CMP) removal rate of tantalum by silica slurries was shown to be directly correlated with the interaction parameters, derived from the NMR relation times rather than with total surface hydroxyl group concentration.     

The exponential power law: partial wetting kinetics and dynamic contact angles

An equation for the kinetics of partial drop spreading is proposed. This equation was empirically derived from experimental data for the spreading kinetics of partially wetting liquids in terms of the wet area versus time. The equation has the form of an exponential power law (EPL), and transforms into the well-known power law for complete wetting, when the equilibrium contact angle approaches zero. The EPL fits very well available experimental data. To lend additional support to the validity of this generalized equation, it will be demonstrated that when it is transformed to present the dynamic contact angle (DCA), it fits very well DCA experimental data for other wetting processes, such as capillary flow and tape coating.     

Preparation and characterization of finely dispersed drugs. 5. Ethyl 3,5-di(acetylamino)-2,4,6-triiodobenzoate

Controlled precipitation of the diagnostic imaging agent ethyl 3,5-di(acetylamino)-2,4,6-triiodobenzoate has been used to produce fine particles of various sizes, morphologies, and degrees of crystallinity, which depended on experimental conditions. In addition, two distinct polymorphic forms of the drug have been fully characterized by single crystal X-ray diffraction studies, and evidence for a third polymorph was also observed. Some of the so prepared dry particles were coated with a thin layer of silica.     

A nucleophilic substitution reaction in microemulsions based on either an alcohol ethoxylate or a sugar surfactant

A nucleophilic substitution reaction between 4-tert-butylbenzyl bromide and a series of iodide salts has been performed in oil-in-water microemulsions based on either a fatty alcohol ethoxylate or a sugar surfactant. The reaction kinetics was compared with the kinetics of the same reaction performed in a microhomogeneous reaction medium, d-MeOH. Previous results showing a particularly high reactivity in the microemulsion based on the fatty alcohol ethoxylate was confirmed. It was shown that in both microemulsions the reaction rate was almost independent of the choice of counterion to iodide. This indicates that complexation of the cation with the surfactant headgroup, which, in particular, could have taken place with surfactants containing oligooxyethylene chains (a “crown ether effect”), seems not to be of importance.

¹²⁷I NMR studies, as well as quadrupole splitting experiments performed by ²H NMR, indicate that there is a certain accumulation of iodide at the oil–water interface of the microemulsions. It is difficult to draw any quantitative conclusions in this respect, however.

The results obtained in this study, combined with results from previous investigations of the same reaction, indicate that the unexpectedly high reactivity obtained in the microemulsion based on a surfactant containing an oligooxyethylene headgroup is most probably due to the nucleophile being poorly solvated when present in the headgroup layer of such a microemulsion. Poorly solvated anions are known to be highly reactive nucleophiles.     

用于激光推进的高功率激光器的选择

 从激光推进的要求出发，阐述了用于激光推进的高功率激光器的选择原则，即激光器必须满足：（1）高的平均功率和峰值功率；（2）高的单脉冲能量；（3）高的重复频率；（4）优良的大气传输特性。主要分析了目前YAG固体激光器、自由电子激光器和TEA脉冲CO₂激光器的特点，通过上述4个方面性能的比较，认为在目前水平下，TEA脉冲CO₂激光器是进行激光推进的首选强激光源，其优点表现在：功率可达10kW量级，单脉冲能量可达0.5~1kJ，重复频率为20~40Hz；激光波长处于大气传输窗口，对大气变化不敏感；工作物质快速流动，不存在热透镜效应和破坏阈值；相关光学元件易于制造；光束质量较好；运行成本低。