Evaluation of automated direct sample introduction with comprehensive two-dimensional gas chromatography/time-of-flight mass spectrometry for the screening analysis of dioxins in fish oil

An automated direct sample introduction technique coupled to comprehensive two-dimensional gas chromatography-time of flight mass spectrometry (DSI-GC x GC/TOF-MS) was applied for the development of a relatively fast and easy analytical screening method for 17 polychlorinated dibenzo-p-dioxins/dibenzofurans (PCDD/Fs) and 4 non-ortho polychlorinated biphenyls (PCBs) in fish oil. Comparison of instrumental performance between DSI-GC x GC/TOF-MS and the traditional gas chromatographic high resolution mass spectrometric (GC-HRMS) method showed good agreement of results for standard solutions analyzed in blind fashion. Relatively high tolerance of the DSI technique for lipids in the final extracts enabled a streamlined sample preparation procedure that only required gel permeation chromatography (GPC) and solid-phase extraction (SPE) cleanup with graphitized carbon black. The sample size for the method was 2g of cod liver oil, which achieved limits of quantitation (LOQs) of 0.019-7.8 pg/g toxic equivalent quotients for the individual PCDD/Fs. Lower detection limits can be achieved by using larger sample size and scaling up the sample preparation procedure, but this adds to the labor, time, solvent consumption, and expense of the approach. However, the streamlined method yielded 0.94 pg/g and 2.3 pg/g LOQs for 2,3,7,8-tetrachloro dibenzofuran (TCDF) and 3,3',4,4',5-pentachloro biphenyl (CB126), which were sufficiently low for regulatory monitoring of 2g samples. Therefore, instead of congener specific analysis, this streamlined analytical screening method for TCDF and CB126 has the potential to monitor fish oil contaminated with dioxin and dioxin-like PCBs at or above current food safety limits. Acceptable recoveries for nearly all analytes at three different spiking levels in fish oil samples were achieved with good repeatability.     

Separation of organic cations using novel background electrolytes by capillary electrophoresis

A background electrolyte for capillary electrophoresis containing tris(-hydroxymethyl) aminomethane (THAM) and ethanesulfonic acid (ESA) gives excellent efficiency for separation of drug cations with actual theoretical plate numbers as high as 300,000. However, the analyte cations often elute too quickly and consequently offer only a narrow window for separation. The best way to correct this is to induce a reverse electroosmotic flow (EOF) that will spread out the peaks by slowing their migration rates, but this has always been difficult to accomplish in a controlled manner. A new method for producing a variable EOF is described in which a low variable concentration of tributylammonium- or triethylammonium ESA is added to the BGE. The additive equilibrates with the capillary wall to give it a positive charge and thereby produce a controlled opposing EOF. Excellent separations of complex drug mixtures were obtained by this method.     

Stereostructure assignment of flexible five-membered rings by GIAO 13C NMR calculations: prediction of the stereochemistry of elatenyne

The stereochemistry of conformationally mobile five-membered rings is often hard to assign from NMR data, and [2,2']bifuranyl systems are even more challenging. GIAO (13)C NMR chemical shifts have been calculated for a series of [2,2']bifuranyl and pyranopyran species, taking into account their conformational flexibility using weighted averages of the data for all low energy conformers. We show that calculation of (13)C NMR chemical shifts using the geometries obtained using molecular mechanics greatly reduces the computational expense without a significant loss of accuracy, even in this demanding system. The results were sufficiently accurate to distinguish not only the pyran and furanyl isomers but also between all the diastereoisomeric forms. As a result of this validation, we predict the stereochemistry for the recently proposed revised structure of the natural product elatenyne, which contains a [2,2']bifuranyl core.     

Solid-phase synthesis of asymmetrically substituted "AB3-type" phthalocyanines

Synthesis of phthalocyanines with asymmetrical substitution on the periphery is often difficult due the problems in purification of the phthalocyanine mixtures obtained. Using a poly(ethylene glycol) (PEG)-based support with a Wang-type linker, we have developed the synthesis of monohydroxylated, oligoethylene glycol substituted phthalocyanines utilizing an amidine-base-promoted phthalonitrile tetramerization reaction. The use of a hydrophilic support allows symmetrical phthalocyanine product formed in solution to be readily and completely removed by washing while leaving the "AB3" product on the support. Acid cleavage with 10% trifluoroacetic acid provides the pure unsymmetrically substituted Pc. This method was applied to several metallo Pcs. Additionally, methods to avoid premature reactions on-resin that give A2B2 products are provided.     

Copper and palladium complexes with N-heterocyclic carbene ligands functionalised with carboxylate groups

The new imidazolium salts functionalised with the trimethylsilyl ester group 1a–c, were easily obtained by quaternisation of alkyl- or aryl-imidazoles with trimethylsilyl bromoacetate. Salt 1a was isolated and fully characterised. It reacted with mesityl copper (Cu₅Mes₅) under trimethylsilyl abstraction to form the complex 2. Methanolysis of 1a–c gave good yields of the carboxylic acid functionalised imidazolium salts 3a–c. Deprotonation of the latter in liquid ammonia led to the zwitterionic imidazolium carboxylates 4a–c. Reaction of 4a with (Cu₅Mes₅) gave solutions from which the insoluble polymeric 5a crystallised slowly. Generation of the carboxylate-functionalised NHC in situ followed by reaction with Pd(OOCCH₃)₂ gave the new complex 6a in which the NHC-carboxylate ligand is chelate bidentate.     

Density functional theory and CCSD(T) evaluation of ionization potentials,redox potentials,and bond energies related to zirconocene polymerization catalysts

Quantum-mechanical-based computational design of molecular catalysts requires accurate and fast electronic structure calculations to determine and predict properties of transition-metal complexes. For Zr-based molecular complexes related to polyethylene catalysis, previous evaluation of density functional theory (DFT) and wavefunction methods only examined oxides and halides or select reaction barrier heights. In this work, we evaluate the performance of DFT against experimental redox potentials and bond dissociation enthalpies (BDEs) for zirconocene complexes directly relevant to ethylene polymerization catalysis. We also examined the ability of DFT to compute the fourth atomic ionization potential of zirconium and the effect the basis set selection has on the ionization potential computed with CCSD(T). Generally, the atomic ionization potential and redox potentials are very well reproduced by DFT, but we discovered relatively large deviations of DFT-calculated BDEs compared to experiment. However, evaluation of BDEs with CCSD(T) suggests that experimental values should be revisited, and our CCSD(T) values should be taken as most accurate.     

Photoinduced electron transfer dynamics in porphyrin donor dyads

Intramolecular photoinduced electron transfer (PET) processes occurring in dyads with a free base porphyrin-tetraazaanthracene donor (P) and either a tetracyanonaphthoquinidodimethane (TCQ) or benzoquinone (BQ) acceptor linked by a rigid six σ-bond polynorbornane bridge ([6]) have been investigated. For P[6]BQ, PET in the polar solvent benzonitrile (_s = 25.9) occurs with a rate constant (k_PET) of 1.6 × 10⁸ s⁻¹ but is not evident in solvents less polar than tetrahydrofuran (_s = 7.52). For P[6]TCQ, highly efficient forward PET occurs in both polar and non-polar solvents (k_PET > 2 × 10¹⁰ s⁻¹). For P[6]TCQ the lifetime of the resulting charge-separated state decreases markedly with increasing solvent polarity. The results are discussed in the context of the likely mechanisms for electronic coupling and current theories for PET processes in such linked molecular systems.     

Xanthene-Based Nitric Oxide-Responsive Nanosensor for Photoacoustic Imaging in the SWIR Window

Shortwave infrared (SWIR) dyes are characterized by their ability to absorb light from 900 to 1400 nm, which is ideal for deep tissue imaging owing to minimized light scattering and interference from endogenous pigments. An approach to access such molecules is to tune the photophysical properties of known near-infrared dyes. Herein, we report the development of a series of easily accessible (three steps) SWIR xanthene dyes based on a dibenzazepine donor conjugated to thiophene ( SCR-1 ), thienothiophene ( SCR-2 ), or bithiophene ( SCR-3 ). We leverage the fact that SCR-1 undergoes a bathochromic shift when aggregated for in vivo studies by developing a ratiometric nanoparticle for NO ( rNP-NO ), which we employed to successfully visualize pathological levels of nitric oxide in a drug-induced liver injury model via deep tissue SWIR photoacoustic (PA) imaging. Our work demonstrates how easily this dye series can be utilized as a component in nanosensor designs for imaging studies.     

Barrier properties of polymer/alumina nanocomposite membranes fabricated by atomic layer deposition

Novel polymer/ceramic nanocomposite membranes were fabricated, characterized and tested for their barrier performance. Atomic layer deposition (ALD) was used to deposit alumina films on primary, micron-sized (16 and 60 μm) high-density polyethylene (HDPE) particles at a rate of 0.5 nm/cycle at 77 °C. Well-dispersed polymer/ceramic nanocomposites were obtained by extruding alumina coated HDPE particles. The dispersion of alumina flakes can be controlled by varying the number of ALD coating cycles and substrate polymer particle size. The diffusion coefficient of fabricated nanocomposite membranes can be reduced to half with the inclusion of 7.29 vol.% alumina flakes. However, a corresponding increase in permeability was also observed due to the voids formed at or near the interface of the polymer and alumina flakes during the extrusion process, as evidenced by electron microscopy. The low surface wettability of the alumina outerlayers was believed to be one of the main reasons of void formation. Particle surface wettability was improved using 3-aminopropyltriethoxysilane (APS) to coat the particle ALD surface modified polymer particles prior to extrusion. The diffusion coefficient and permeability of the membrane using surfactant-modified particles decreased by 20%, relative to the non-modified case.     

Incorporation of block copolymer micelles into multilayer films for use as nanodelivery systems

This work demonstrates the potential application of stimulus responsive block copolymer micelles as triggerable delivery systems for use within multilayer films. Cationic, pH-responsive micelles of poly[2-(dimethylamino)ethyl methacrylate-block-poly(2-(diethylamino)ethyl methacrylate)] (PDMA-PDEA) were deposited on anionic polystyrene latex particles. The charge reversal of the surface and the amount of adsorbed polymer were monitored by zeta potential measurements and colloidal titrations, respectively. Prior to adsorption, the PDMA-PDEA micelles were loaded with a hydrophobic dye, and UV-vis spectroscopy was used to determine the amount of dye encapsulated within a monolayer of micelles. It was found that subtle chemical modification of the PDMA-PDEA diblock copolymer via permanent quaternization of the PDEA block results in micelles with tunable loading capacities. Multilayers of cationic micelles of partially quaternized PDMA-PDEA and anionic polyelectrolyte (poly(sodium 4-styrene sulfonate)) were deposited on the surface of polystyrene latex particles by sequential adsorption. UV-vis analysis of the dye present within the multilayer after the addition of each layer demonstrates that the micelles are sufficiently robust to retain encapsulated dye after multiple adsorption/washing cycles and can thus create a film that can be increasingly loaded with dye as more micelle layers are adsorbed. Multiple washing cycles were performed on micellar monolayers of PDMA-PDEA to demonstrate how such systems can be used to bring about triggerable release of actives. When performing several consecutive washing steps at pH 9.3, the micelle structure of the PDMA-PDEA micelles in the monolayer is retained, resulting in only a small reduction in the amount of encapsulated dye. In contrast, washing at pH 4, the structure of the micelle layers is severely disrupted, resulting in a fast release of the encapsulated dye into the bulk. Finally, if a sufficient number of micelle/homopolyelectrolyte layers are adsorbed, it is possible to selectively dissolve the latex template, resulting in hollow capsules.