Coercivity analysis in R17Fe83−χBχ magnets

We studied the coercivity in magnets of composition R₁₇Fe_83−χB_χ (R = Nd, Pr and χ = 8, 30), using measurements of the coercive field H_c, its angular dependence, and the magnetic viscosity coefficient S_v, for temperatures between 4.2 and 500 K. The results are discussed in relation to a model which does not specifically consider the detailed mechanisms involved in magnetization reversal, but which provides information about the magnetic properties in the activation volume v where magnetization reversal is initiated. It is concluded that the ordering temperature in v tends to be slightly smaller than in the bulk and that the room temperature anisotropy in v is not strongly reduced with respect to the bulk value. Finally, a direct evaluation of the dipolar interactions is in good agreement with results obtained from H_c(T).     

Ferroelectric polarization switching in nylon-11

Cold-drawn Nylon-11 films, which were prepared by stretching the melt-quenched films to a draw ratio of 2.8: 1 at room temperature, were found to exhibit an electric displacement versus electric field hysteresis loop. The results confirmed that the Nylon-11 film exhibited ferroelectric behavior at or below room temperature. The coercive fields were 65, 98, 125, 160, and 215 MV/m at 20, 0, ?20, ?40, and ?60°C and the remanent polarization at ?20°C (where there was considerably less dc conduction) was 56 mC/m². Switching of the polarization was almost completed within 20 ms.     

AUTOMATED WIND TUNNEL MEASUREMENTS

It is common practice in power transmission to use bundled overhead electrical conductors because the lower rate of corona discharge, compared with single conductors, makes the bundle attractive for high voltages. However, secondary problems may arise from the vibrations induced by the aerodynamic forces which act on the leeward conductors as a result of their immersion in the wake of a windward conductor. Thus, in addition to possible aeolian and galloping oscillations observed for a single conductor, bundle conductors may also be subjected to wake-induced oscillations. ^1,2 Although extensive research has been done on the aeroelastic behavior of single and bundled conductors which are bare, little is known about the galloping or wake oscillation characteristics of given bundle conductors which, depending upon the environmental conditions during the formation of ice, may have five or so representative shaped cross-sections. One important task involves the aerodynamic quasi-static force and moment measurements in a wind tunnel using full scale conductor cross-sections each of which must be rotated through many angles at different spacings. Such measurements are repetitive as well as tediously time consuming and, hence, are beneficially automated. A reliable, accurate and inexpensive automated apparatus is described in this paper which permits the aerodynamic measurements to be performed efficiently and without intervention. Most importantly, it relieves the operator of the usual responsibility for manually controlling the separation and orientation of the sections as well as the need to manually compensate fluctuations in the free stream air speed. For simplicity, the apparatus is detailed in the context of a twin bundle conductor.     

Identification of peroxyacetic acid uroporphyrin I in the urine of patients with congenital erythropoietic porphyria by liquid chromatography and mass spectrometry

A new porphyrin, peroxyacetic acid uroporphyrin I, has been isolated from the urine of patients with congenital erythropoietic porphyria by reversed phase high performance liquid chromatography. The porphyrin was characterized by high resolution mass spectrometry and by typical chemical reactions of a peroxyacid.     

Low-energy ion-assisted control of interfacial structures in metallic multilayers

A molecular dynamics method has been used to simulate the argon ion-assisted deposition of Cu/Co/Cu multilayers and to explore ion beam assistance strategies that can be used during or after the growth of each layer to control interfacial structures. A low-argon ion energy of 5–10 eV was found to minimize a combination of interfacial roughness and interlayer mixing (alloying) during the ion-assisted deposition of multilayers. However, complete flattening with simultaneous ion assistance could not be achieved without some mixing between the layers when a constant ion energy approach was used. It was found that multilayers with lower interfacial roughness and intermixing could be grown either by modulating the ion energy during the growth of each metal layer or by utilizing ion assistance only after the completion of each layers deposition. In these latter approaches, relatively high-energy ions could be used since the interface is buried and less susceptible to intermixing. The interlayer mixing dependence upon the thickness of the over layer has been determined as a function of ion energy.     

Sliding spark spectroscopy

Summary A new analytical radiation source combined with fiber optics linked to a diode array detection device with modified software is described. The direct-reading spectrometer simultaneously covers the wavelength range 185–510 nm with a spectral resolution of <1.5 nm. Intense optical emission is observed when positionally stable high-current surface sparks supplied by a pulse-generator with definite discharge parameters (max. 800 Ampere/pulse) are sliding over compact non-conductive materials such as plastics, glasses, quartz filters or powder pellets. Substrate vaporization, ionization and excitation processes in the surface discharge plasma channel generate emission corresponding to neutral and ionic states. The spectra are essentially composed of lines emitted by the electrode material (e.g. copper, silver), from the substrate under investigation, radiation continuum as well as structured background from the surrounding air atmosphere. Due to the occurrence of emission lines of reactive fillers, inorganic pigments and stabilizers, a rapid multi-element screening method is demonstrated. A rapid identification system (mix-up test) of PVC or fire-retardant thermoplastics within one second has been realized from the atomic emission line intensity originating from the sputtered copper electrode material according to its increased volatility in the presence of chlorine (modified Beilstein test).Puls-Plasma-Technik GmbH, Dortmund