Fully developed mixed convection in horizontal and inclined tubes with uniform heat flux using nanofluid

Fully developed laminar mixed convection of a nanofluid consists of water and Al₂O₃ in horizontal and inclined tubes has been studied numerically. Three-dimensional elliptic governing equations have been solved to investigate the flow behaviors over a wide range of the Grashof and Reynolds numbers. Comparisons with previously published experimental and numerical works on mixed convection in a horizontal and inclined tube are performed and good agreements between the results are observed. Effects of nanoparticles concentration and tube inclinations on the hydrodynamics and thermal parameters are presented and discussed. It is shown that the nanoparticles concentration does not have significant effects on the hydrodynamics parameters. Heat transfer coefficient increases by 15% at 4 Vol.% Al₂O₃. Skin friction coefficient continually increases with the tube inclination, but the heat transfer coefficient reaches a maximum at the inclination angle of 45°.     

Effect of oxygen deficit and nonuniform distribution of technological impurities on the dielectric properties of Y3Fe5O12 crystals

The experimental and calculated values of the optical permittivity ε_∞ have been analyzed and generalized with allowance for the oxygen concentration and possible valences of Fe and O ions in YIG single crystals. It is shown that the deficit of oxygen ions in the samples is accompanied by a decrease in ε_∞. A decrease in the gradient of distribution of Ba ions over the sample thickness decreases the difference between the calculated and experimental values. It is revealed that the ratio of the number of valence electrons to the number of core electrons, with regard to their polarizabilities, is proportional to the ratio of the incoherent and coherent X-ray scattering intensities, nk/k.     

Accuracy analysis of airborne gravimeter calibration using repeated flight paths

Some possible errors in determining the gravity anomalies are discussed. Such errors may be caused by an inaccurate calibration of the gravimeter used in an airborne survey system. An approach based on wavelet decompositions is proposed for its additional calibration with the use of flight data obtained during repeated flights.     

Microstructure dependent dynamic fracture analyses of trabecular bone based on nascent bone atomistic simulations

Trabecular bone fracture is closely related to the trabecular architecture, microdamage accumulation, and bone tissue properties. Primary constituents of trabecular tissue are hydroxyapatite (HA) mineralized type-I collagen fibers. In this research, dynamic fracture in two dimensional (2-D) micrographs of ovine (sheep) trabecular bone is modeled using the mesoscale cohesive finite element method (CFEM). The bone tissue fracture properties are obtained based on the atomistic strength analyses of a type-I collagen + HA interfacial arrangement using molecular dynamics (MD). Analyses show that the presented framework is capable of analyzing the architecture dependent fracture in 2-D micrographs of trabecular bone.     

Parametric oscillations and stability of systems with large modulation coefficient

We study parametric oscillations of linear systems with one degree of freedom for large values of the modulation coefficient. We use the classical analytic Lyapunov-Poincaré perturbation methods and an original numerically-analytic method of accelerated convergence to construct periodic solutions and the corresponding eigenvalues. We find the boundaries of stability and instability domains. We use specific models to illustrate the main properties of parametric oscillations of systems with singular character of the perturbation dependence on the modulation coefficient. We consider periodic boundary value problems for the modified Mathieu equation and the Kochin equation modeling crankshaft torsional vibrations and show that there are significant differences between weakly and essentially perturbed periodicmotions both for the lowest and arbitrary oscillation modes. We also describe the unusual properties of the boundaries in the domain of the system determining parameters.     

A quality criterion for visual tracking during nystagmus

The aim of this study is to construct a quantitative characteristic for the degree of gaze stabilization on a visual target with consideration of physiological constraints. A quality criterion for visual tracking during optokinetic vestibulocervical nystagmus is proposed. The index of imaginary tracking during rotation in the dark allows one to speak of a difference in the image stabilization quality between a healthy person and a patient. Experimental nystagmus data are used to calculate the quality index of visual tracking and the index of imaginary tracking.     

Multi-mode wave propagation in ribbed plates: Part I,wavenumber-space characteristics

This paper addresses the issue of energy propagation features in ribbed panels over a wide frequency range. First, a tool for estimating the wave propagation characteristics of one- and two-dimensional structures by k-space analysis is presented. This tool uses a concept of Inhomogeneous Wave Correlation with sparse measured or extracted data, and leads to the estimation of θ-dependent wavenumbers. Here, the method is employed with the sparse simulated and measured normal velocities of a set of ribbed panels and new insights into their k-space behavior are highlighted. Behavior is essentially characterized at low frequencies by structural orthotropy. Comparisons with homogenized data show very good agreement. At higher frequencies, a new behavior pattern is observed and explained both numerically and experimentally. This is a multi-modal waveguide type of propagation in a direction parallel to the ribs.     

Buckling of a stiff thin film on a compliant substrate in large deformation

A finite-deformation theory is developed to study the mechanics of thin buckled films on compliant substrates. Perturbation analysis is performed for this highly nonlinear system to obtain the analytical solution. The results agree well with experiments and finite element analysis in wavelength and amplitude. In particular, it is found that the wavelength depends on the strain. Based on the accurate wavelength and amplitude, the membrane and peak strains in thin films, and stretchability and compressibility of the system are also obtained analytically.     

Multi-layer thin films/substrate system subjected to non-uniform misfit strains

Current methodologies used for the inference of thin film stress through curvature measurement are strictly restricted to stress and curvature states that are assumed to remain uniform over the entire film/substrate system. These methodologies have recently been extended to a single layer of thin film deposited on a substrate subjected to the non-uniform misfit strain in the thin film. Such methodologies are further extended to multi-layer thin films deposited on a substrate in the present study. Each thin film may have its own non-uniform misfit strain. We derive relations between the stresses in each thin film and the change of system curvatures due to the deposition of each thin film. The interface shear stresses between the adjacent films and between the thin film and the substrate are also obtained from the system curvatures. This provides the basis for the experimental determination of thin film stresses in multi-layer thin films on a substrate.     

Stress concentration and effective stiffness of aligned fiber reinforced composite with anisotropic constituents

The paper addresses the problem of calculation of the local stress field and effective elastic properties of a unidirectional fiber reinforced composite with anisotropic constituents. For this aim, the representative unit cell approach has been utilized. The micro geometry of the composite is modeled by a periodic structure with a unit cell containing multiple circular fibers. The number of fibers is sufficient to account for the micro structure statistics of composite. A new method based on the multipole expansion technique is developed to obtain the exact series solution for the micro stress field. The method combines the principle of superposition, technique of complex potentials and some new results in the theory of special functions. A proper choice of potentials and new results for their series expansions allow one to reduce the boundary-value problem for the multiple-connected domain to an ordinary, well-posed set of linear algebraic equations. This reduction provides high numerical efficiency of the developed method. Exact expressions for the components of the effective stiffness tensor have been obtained by analytical averaging of the strain and stress fields.