Supersymmetric spin glass

The manifestly supersymmetric four-dimensional Wess-Zumino model with quenched disorder is considered at the one-loop level. The infrared fixed points of a beta function form the moduli space ℳ=RP ², where two types of phases are found: with and without replica symmetry. While the former phase possesses only a trivial fixed point, this point become unstable in the latter phase, which may be interpreted as a spin glass phase. Pis’ma Zh. éksp. Teor. Fiz. 65, No. 8, 657–662 (25 April 1997) Published in English in the original Russian journal. Edited by Steve Torstveit.     

Shell effects in the symmetric-modal fission of pre-actinide nuclei

Mass distributions of fragments in the low-energy fission of nuclei from ¹⁸⁷Ir to ²¹³At have been analysed. This analysis has shown that shell effects in symmetric-mode fragment mass yields from the fission of pre-actinide nuclei could be described if one assumes the existence of two strongly deformed neutron shells in the arising fragments with neutron numbers N₁ ≈ 52 and N₂ ≈ 68. A new method has been proposed for quantitatively describing the mass distributions of the symmetric fission mode for pre-actinides with A ≈ 180–220.     

Time-resolved synchrotron X-ray study of crystalline phase transition in poly(aryl ether ketone ketone) containing alternated terephthalic/isophthalic moieties

Unique crystallization and melting behavior in poly(aryl ether ketone ketone) containing alternated terephthalic and isophthalic moieties were studied by time-resolved synchrotron x-ray methods. Recently, this material has been shown to exhibit three polymorphs (forms I, II, and III). In this work, we further investigated their distinctive thermal properties and found that form I is the dominating and the most thermally stable phase while form II is favored by fast nucleation conditions and is the least stable phase. On the other hand, form III represents a minor intermediate phase that usually coexists with form I and can be transferred from form II and to form I. Structural and morphological changes in form I have been followed by simultaneous wide-angle x-ray diffraction (WAXD)/small-angle x-ray scattering (SAXS) measurements during cold- or melt-crystallization and subsequent melting. In all cases, a larger dimensional change was found in the crystallographic a-axis than the b-axis during heating and cooling. This may be due to the greater lateral stress variation with respect to temperature along the a direction of the primary lamellae which is induced by either the formation of secondary lamellae or the preferential chain-folding direction in poly(aryl ether ketone ketone)s. During the phase transitions of form II ← III in the cold-crystallized specimen and form III ← I in the melt-crystallized samples, lamellar variables (long period, lamellar thickness, and invariant) obtained from SAXS remain almost constant. This indicates that the density distribution in the long spacing is independent of the melting in form II or III. For melt-crystallization, the corresponding changes in unit-cell dimensions and lamellar morphology during the annealing-induced low endotherm are most consistent with the argument that these changes are due to the melting of thin lamellar population. © 1995 John Wiley & Sons, Inc.     

Vibrational control of crystal growth from liquid phase

Modeling and numerical simulations of the convective flows induced by the vibration of the monocrystal during crystal growth have been performed for two configurations simulating the Cz and FZ methods. This permitted to emphasize the role of different vibrational mechanisms in the formation of the average flows. It is shown that an appropriate combination of these mechanisms can be used to counteract the usual convective flows (buoyancy- and/or thermocapillary-driven) inherent to crystal growth processes from the liquid phase. While vibrational convection is rather complex due to these identified mechanisms, the new modeling used in the present paper opens up very promising perspectives to efficiently control heat and mass transfer during real industrial applications of crystal growth from the liquid phase.     

Development of new dyes for use in integrated optical sensors

New chromoionophores have been developed, focused on NIR applications so that optode membranes may be used in monolithically integrated optical sensors. The wavelength of maximum absorbance has been estimated for a new model compound by the Pariser-Parr-Pople (PPP) method. Several cyanine type dyes have been tested as membrane chromoionophores. Membrane composition has been altered to overcome solubility problems. In this way, simple pH-sensitive optode membranes have been produced.     

Database reverse engineering: From requirements to CARE tools

This paper analyzes the requirements that CASE tools should meet for effective database reverse engineering (DBRE), and proposes a general architecture for data-centered applications reverse engineering CASE environments. First, the paper describes a generic DBMS-independent DBRE methodology, then it analyzes the main characteristics of DBRE activities in order to collect a set of desirable requirements. Finally, it describes DB-MAIN, an operational CASE tool developed according to these requirements. The main features of this tool that are described in this paper are its unique generic specification model, its repository, its transformation toolkit, its user interface, the text processors, the assistants, the methodological control and its functional extensibility. Finally, the paper describes five real-world projects in which the methodology and the CASE tool were applied. This is a heavily revised and extended version of “Requirements for Information System Reverse Engineering Support” by J.-L. Hainaut, V. Englebert, J. Henrard, J.-M. Hick, D. Roland, which first appeared in the Proceedings of the Second Working Conference on Reverse Engineering, IEEE Computer Society Press, pp. 136–145, July 1995. This paper presents some results of the DB-MAIN project. This project is partially supported by the Région Wallonne, the European Union, and by a consortium comprising ACEC-OSI (Be), ARIANE-II (Be), Banque UCL (Lux), BBL (Be), Centre de recherche public H. Tudor (Lux), CGER (Be), Cockerill-Sambre (Be), CONCIS (Fr), D'Ieteren (Be), DIGITAL, EDF (Fr), EPFL (CH), Groupe S (Be), IBM, OBLOG Software (Port), ORIGIN (Be), Ville de Namur (Be), Winterthur (Be), 3 Suisses (Be). The DB-Process subproject is supported by the Communauté Fran?aise de Belgique.     

AN ALTERNATIVE SPECIFICATION FOR MODELING GROUNDWATER DYNAMICS

This research extends previous work with dynamic models to manage groundwater quality by using the consumptive nitrate use rate instead of the nitrate application rate. The analysis indicates that misspecification results in overestimation of economic benefits, and supra-optimum nitrogen fertilizer application rates and groundwater nitrate stocks at a steady state.     

Orbifolds, Sheaves and Groupoids

We characterize orbifolds in terms of their sheaves, and show that orbifolds correspond exactly to a specific class of smooth groupoids. As an application, we construct fibered products of orbifolds and prove a change-of-base formula for sheaf cohomology.