Redox-iodometry: a new potentiometric method

A new iodometric method for quantifying aqueous solutions of iodide-oxidizing and iodine-reducing substances, as well as plain iodine/iodide solutions, is presented. It is based on the redox potential of said solutions after reaction with iodide (or iodine) of known initial concentration. Calibration of the system and calculations of unknown concentrations was performed on the basis of developed algorithms and simple GWBASIC-programs. The method is distinguished by a short analysis time (2–3 min) and a simple instrumentation consisting of pH/mV meter, platinum and reference electrodes. In general the feasible concentration range encompasses 0.1 to 10^–6 mol/L, although it goes down to 10^–8 mol/L (0.001 mg Cl₂/L) for oxidants like active chlorine compounds. The calculated imprecision and inaccuracy of the method were found to be 0.4–0.9% and 0.3–0.8%, respectively, resulting in a total error of 0.5–1.2%. Based on the experiments, average imprecisions of 1.0–1.5% at c(Ox)>10^–5 M, 1.5–3% at 10^–5 to 10^–7 M, and 4–7% at <10^–7 M were found. Redox-iodometry is a simple, precise, and time-saving substitute for the more laborious and expensive iodometric titration method, which, like other well-established colorimetric procedures, is clearly outbalanced at low concentrations; this underlines the practical importance of redox-iodometry.

---

An erratum to this article is available at .     

Fe(bpb)(CN)2]- as a versatile building block for the design of novel low-dimensional heterobimetallic systems: synthesis, crystal structures, and magnetic properties of cyano-bridged Fe(III)-Ni(II) complexes [(bpb)(2-) = 1,2-bis(pyridine-2-carboxamido)benzenate

A dicyano-containing [Fe(bpb)(CN)2]- building block has been employed for the synthesis of cyano-bridged heterometallic Ni(II)-Fe(III) complexes. The presence of steric bpb(2-) ligand around the iron ion results in the formation of low-dimensional species: five are neutral NiFe2 trimers and three are one-dimensional (1D). The structure of the 1D complexes consists of alternating [NiL]2+ and [Fe(bpb)(CN)2]- generating a cyano-bridged cationic polymeric chain and the perchlorate as the counteranion. In all complexes, the coordination geometry of the nickel ions is approximately octahedral with the cyano nitrogen atoms at the trans positions. Magnetic studies of seven complexes show the presence of ferromagnetic interaction between the metal ions through the cyano bridges. Variable temperature magnetic susceptibility investigations of the trimeric complexes yield the following J(NiFe) values (based on the spin exchange Hamiltonian H = -2J(NiFe) S(Ni) (S(Fe(1)) + S(Fe(2))): J(NiFe) = 6.40(5), 7.8(1), 8.9(2), and 6.03(4) cm(-1), respectively. The study of the magneto-structural correlation reveals that the cyanide-bridging bond angle is related to the strength of magnetic exchange coupling: the larger the Ni-N[triple bond]C bond angle, the stronger the Ni- - -Fe magnetic interaction. One 1D complex exhibits long-range antiferromagnetic ordering with T(N) = 3.5 K. Below T(N) (1.82 K), a metamagnetic behavior was observed with the critical field of approximately 6 kOe. The present research shows that the [Fe(bpb)(CN)2]- building block is a good candidate for the construction of low-dimensional magnetic materials.     

A novel type of Si-containing poly(urethane-imide)s: synthesis, characterization and electrical properties

A novel type of a Si-containing poly(urethane-imide) (PUI) was prepared by two different methods. In the first method, Si-containing polyurethane (PU) prepolymer having isocyanate end groups was prepared by the reaction of diphenylsilanediol (DSiD) and toluene diisocyanate (TDI). Subsequently the PU prepolymer was reacted with pyromellitic dianhydride (PMDA) or benzophenonetetracarboxylic dianhydride (BTDA) in N-methyl pyrolidone (NMP) to form Si-containing modified polyimide directly. In the second method, PU prepolymer was reacted with diaminodiphenylether (DDE) or diaminodiphenylsulfone (DDS) in order to prepare an amine telechelic PU prepolymer. Finally, the PU prepolymer having diamine end groups was reacted with PMDA or BTDA to form a Si-containing modified polyimide. Cast films prepared by second method were thermally treated at 160 °C to give a series of clear, transparent PUI films. Thermogravimetric analysis indicated that the thermal degradation of PUI starts at 265 °C which is higher than degradation temperature of conventional PU, confirming that the introduction of imide groups improved the thermal stability of PU.To characterize the modified polyimides and their films, TGA, FTIR, SEM and inherent viscosity analyses were carried out. The dielectrical properties were investigated by the frequency-capacitance method. Dielectric constant, dielectric breakdown strength, moisture uptake and solubility properties of the films were also investigated.     

Enzyme stabilization strategies based on electrolytes and polyelectrolytes for biosensor applications

The achievements in the area of enzyme stabilization based on electrolytes, polyelectrolytes and polyols is reviewed, in the context of biosensor applications. Both the storage and operational stabilities of the biosensors can be improved using these stabilizers. The deactivation of the enzymes used for the development of biosensors from thermal shock, proteolytic degradation, and non-specific metal-catalyzed oxidation can be drastically reduced with the use of one or more of these stabilizers. It is attempted to deconvolute the effect of these additives on (a) the storage stability or shelf life, and (b) the operational stabilities of the biosensors. Even though there are a large number of techniques and reports dealing with enzyme stabilization, their application to biosensor technology is still very limited. It is thus concluded that the use of the existing enzyme stabilization techniques will have a drastic effect on the storage and operational stabilities of biosensors in the near future.     

Derivatisation in gas chromatographic determination of acidic herbicides in aqueous environmental samples

This paper reviews derivatisation processes applied in chromatographic determination of acidic herbicides (with carboxyl and phenol groups), mainly in aqueous environmental samples. The discussion focuses on the basic derivatisation reactions used to convert herbicides to derivatives to make them analysable by gas chromatography, and possibly to reduce detection limits and/or increase extraction recovery from aqueous samples. The reactions are transesterification, esterification, silylation, alkylation, and extractive and pyrolytic alkylation. The reagents used to conduct the reactions are numerous. Diazomethane is a very efficient methylation reagent but explosive and toxic. Methyl iodide also ensures rapid and efficient methylation. Benzyl bromide can be used directly in water but derivatisation yield is low and reproducibility is poor. Butyl chloroformate and dimethyl sulfite can also be used for derivatisation in water, and acetic anhydride can be used for in-situ derivatisation of phenolic herbicides. For increasing selectivity of GC detection pentafluorobenzyl bromide (for ECD) and (2-cyanethyl)dimethyl(diethylamino)silane (for NPD) have been applied. Very characteristic ions are produced in mass spectra if silyl groups are introduced, e.g. by using bis(trimethylsilyl)trifluoroacetamide. Tetramethylammonium, trimethylphenylammonium, tetraalkylammonium, and trimethylsulfonium hydroxides and salts can by used for derivatisation at elevated temperature in the GC injection port. Extractive alkylation is relatively efficient if tetraalkylammonium salts with long chain alkyl groups are used.     

Determination of chlorite in drinking water by differential pulse voltammetry on graphite

The chlorite ion is an unavoidable by-product of the disinfection of drinking water by means of chlorine dioxide. The maximum concentration values of chlorite accepted in many countries regulations range from 0.2 to 1.0 mg L^–1. A simple, inexpensive and quickly set up voltammetric procedure for the on-site determination of chlorite in drinking water networks is described. This procedure is suitable for the whole range of applications in drinking water plants. A useful cell for on-field analysis has been developed. Surface morphology and behaviour of carbon-based working electrodes have been investigated by voltammetry and atomic force microscopy (AFM). Actual samples of different types of water networks have been analysed for chlorite concentration.     

NMR study of some diastereomeric nucleoside-3′-thiophosphate derivatives in solution

The conformational properties of diastereomeric P-modified nucleotides are reported as reflected by different NMR parameters. Some conformational trends can be rationalized by consideration of the ³J(C4,P) and ³J(C2,P) coupling values of the isomers and the nature of the substituent on the phosphorus. Configurational assessment of the phosphorus is inferred from NOE experiments. The effects of temperature, solvent and size of substituents are presented.     

Analysis of the Temperature and Composition Dependence of Viscosimetric Properties of 2-Butanone <Emphasis Type="Bold">+</Emphasis> 2-Butanol Solvent Mixtures

Kinematic viscosities were measured for 2-butanone + 2-butanol binary liquid mixtures with a capillary Ubbelohde routine viscometer in the temperature range from 273.15 to 353.15 K at atmospheric pressure, and covering the whole miscibility field (0x_i1). Experimental data have been correlated by means of different empirical or semiempirical relationships, such as =(T), =(x_i), and =(T, x_i). Viscosity deviations, , from ideal behavior are negative at all experimental conditions, confirming that structure breaking effects prevail in the liquids. Furthermore, the thermodynamics of viscous flow and excess Gibbs energy of activation of viscous flow, G*^E, have been calculated. As an alternative and complementary approach to such investigations, the fluidity () of this binary system has been analyzed by the modified—Batschinski theory. The results are discussed in terms of the specific molecular interactions between the mixture components.     

The influence of simulation conditions in molecular dynamics investigations of model β-sheet peptides

The influence of simulation methods, cutoff based and particle mesh Ewald (PME) on the accuracy by which experimentally derived nuclear Overhauser effect (NOE) data are reproduced, has been investigated using 500-ns-long molecular dynamics simulations on a model -sheet peptide in explicit solvent. The structural and conformational features under the different conditions were evaluated in terms of flexibility, secondary structure content, hydrogen-bonding pattern and percent of native contacts as a function of time. It was found that the different simulation methods strongly influence the dynamics of the peptide, confirming previous observations based on ideal peptide models simulated for much shorter times. Moreover, the results of our simulations prove once more that it is necessary to reach extremely long time scales to obtain enough statistics to accurately reproduce experimental NOE restraints even in the case of the PME method, despite its tendency to the stabilization of conformations which are structurally closely related to the ones derived through experiment. Possible implications regarding the stabilization and folding mechanisms, together with their relationship to the experimental study of peptide models, are discussed.     

Shipboard analysis of picomolar levels of manganese in seawater by chelating resin concentration and chemiluminescence detection

A new shipboard analytical method for determining picomolar levels of manganese in seawater has been developed. The method is based on a combination of chelating resin column extraction and improved chemiluminescence (CL) detection in a closed flow system. In this method, manganese in sample solution is selectively collected on newly-developed iminodiacetate-immobilized chelating resin, and then eluted with acidic solution containing hydrogen peroxide. The resulting eluent is mixed with luminol solution and aqueous ammonia after removal of iron ions by a chelating resin column, and then the mixture is introduced into the CL cell. The manganese concentration is obtained from the CL intensity. The detection limit (3SD) of manganese is 5 pmol L^–1 from 9 mL of seawater sample. The method was applied to seawater samples collected at the Okinawa Trough.