Degradation of ²-O-4 lignin model and related compounds by the ascomyceteChrysonilia sitophila (TFB 27441 strain)

Growth of the ascomyceteChrysonilia sitophila during degradation of lignin model dimers and monomers was compared to a glucose control. An inhibition of growth by Cα-carbonyl monomers and stimulation by β-O-4 lignin model and vanillyl alcohol were observed. A comparison of the degradation by this ascomycete with the basidiomycetePhanerochaete chrysosoporium showed similarities in relation to the type of degradation caused.     

Determination of copper in medicinal plants used as dietary supplements by atomic absorption spectrometry with direct flame solid analysis

An alternative device for the direct solid analysis (DSA) for copper determination by flame atomic absorption spectrometry (FAAS) is proposed. Copper was directly determined in commercial medicinal plants used as dietary supplements. The determination of copper in solid samples by DSA–FAAS was made by using a conventional air–acetylene flame. Between 0.05 and 1.5 mg of each test, sample was weighed directly into a small polyethylene vial connected to the device used for solid introduction into the flame. Test samples were introduced into the flame as a dry aerosol using a T-quartz cell set between the burner and the optical path. The T-quartz cell has a slit in the superior part by which the solid aerosol passes to the flame. A transient signal, evaluated as integrated absorbance, is produced and it is totally integrated in 2 s. Background signals always presented absorbance values less than 0.1. It was found a characteristic mass of 0.8 ng Cu and absolute limit of detection of 1.2 ng (3 s), or 1.2 μg g⁻¹ if a sample mass of 1 mg was used. Optimized conditions for air flow rate, flame stoichiometry, and so on were established as well. No excessive grinding of the samples was needed and samples with particle of size less than 80 μm were used throughout. No statistical difference between the results from the proposed system and those obtained by sample digestion and determination by conventional FAAS was observed. With the proposed procedure, more than 50 test samples can be analyzed in 1 h and it can be easily adapted to conventional spectrometers for FAAS.     

The deformation of dextran molecules. Causes and consequences in ultrafiltration

The transfer of dextran T70 solutions through a skinned polysulfone hollow fiber membrane was studied with and without applied pressure. The molecular weight distributions of dextran in the feed and in the permeate were obtained by high pressure liquid chromatography. Two different phenomena appear to play important roles with regard to solute transfer. One is related to the shear stress imposed by the flow at the pore entrances, i.e. to permeate flux, and the other is related to the influence of solute concentration on the expansion of the macromolecular chains. These phenomena explain the observed variations with operating conditions of the overall rejection coefficient.     

Babassu mesocarp (Orbignya phalerata Mart) nanoparticle-based biosensors for indirect sulfite detection in industrial juices

Journal of Solid State Electrochemistry - The present work proposes a new electrochemical sulfite biosensor based on babassu mesocarp nanoparticles (BMNPs) immobilized on the surface of a pyrolytic...     

Highly corrosion resistant siloxane-polymethyl methacrylate hybrid coatings

Siloxane-polymethyl methacrylate hybrid films were deposited on carbon steel substrates by dip-coating from a sol prepared by acid-catalyzed hydrolytic co-polycondensation of tetraethoxysilane (TEOS) and 3-methacryloxy propyl-trimethoxysilane (MPTS), followed by radical polymerization of methyl methacrylate (MMA). Structural properties of the hybrids were studied using ²⁹Si and ¹³C nuclear magnetic resonance (NMR), X-ray photoelectron spectroscopy (XPS) and thermogravimetric analysis (TGA), as a function of the MMA/MPTS ratio, which ranged between 2 and 10. The efficiency of corrosion protection of hybrid-coated carbon steel was investigated by XPS, potentiodynamic polarization curves and electrochemical impedance spectroscopy after immersion of the material in acidic and neutral saline aqueous solution. The NMR and TGA results indicate a high degree of polycondensation (84%) and elevated thermal stability of 410?°C for the hybrid film with a MMA/MPTS ratio of 8, exhibiting also and excellent adhesion to the substrate. The XPS analysis confirmed the variation of the MMA phase in the hybrid, and showed that no corrosion-induced changes had occurred after 18?days immersion of the coated steel in 3.5% NaCl solution. Potentiodynamic polarization curves have shown that the hybrid coating prepared using a TEOS/MPTS ratio of 8 yielded the best anti-corrosion performance. It acts as a very efficient corrosion barrier, increasing the total impedance by almost 6 orders of magnitude and reducing the current densities by 4 orders of magnitude, compared to the bare electrode. The obtained results are discussed based on the correlation of structural information with impedance data presented for both electrolytes in the form of electrical equivalent circuits.     

Chemometric Strategies to Develop a Nanocomposite Electrode for Simultaneous Determination of Ascorbic Acid,Dopamine, and Uric Acid

A simple and sensitive method for simultaneously measuring dopamine (DA), ascorbic acid (AA), and uric acid (UA) using a poly(1‐aminoanthracene) and carbon nanotubes nanocomposite electrode is presented. The experimental parameters for composite film synthesis as well as the variables related to simultaneous determination of DA, AA, and UA were optimized at the same time using fractional factorial and Doehlert designs. The use of carbon nanotubes and poly(1‐aminoanthracene) in association with a cathodic pretreatment led to three well‐defined oxidation peaks at potentials around ?0.039, 0.180 and 0.351 V (vs. Ag/AgCl) for AA, DA, and UA, respectively. Using differential pulse voltammetry, calibration curves for AA, DA, and UA were obtained over the range of 0.16–3.12×10^?3 mol L^?1, 3.54–136×10^?6 mol L^?1, and 0.76–2.92×10^?3 mol L^?1, with detection limits of 3.95×10^?5 mol L^?1, 2.90×10^?7 mol L^?1, and 4.22×10^?5 mol L^?1, respectively. The proposed method was successfully applied to determine DA, AA, and UA in biological samples with good results.     

The effects of lignin removal and drying on the porosity and enzymatic hydrolysis of sugarcane bagasse

The porosity of lignocellulosic materials is a key feature for the enzymatic hydrolysis of the constituent polysaccharides, being affected by its drying and lignin content. Here we evaluated the influence of both parameters in the porosity of sugarcane bagasse, using raw and chlorite-delignified samples. A fraction of these samples was air dried at room temperature and the remainder one was kept wet. All the samples were subjected to porometry (solute exclusion technique), determination of water retention value and assessment of enzymatic saccharification of polysaccharides. Samples with higher lignin contents had lower porosities and exhibited worse enzymatic conversions of polysaccharides. Mild drying collapsed only the smaller pores, which already were inaccessible to enzymes, and therefore did not affect the efficiencies of saccharification. Our results show that the lignin content plays an important role in the porosity of the material and that its removal improves the enzymatic saccharification of the constituent polysaccharides.