Investigation of defect centres responsible for TL/OSL in MgAl2O4:Tb

Magnesium aluminate doped with Tb³⁺ (MgAl₂O₄:Tb³⁺) was prepared by combustion synthesis. Three thermoluminsence (TL) peaks at 120, 220 and 340 °C were observed. PL and TL emission spectrum shows that Tb³⁺ acts as the luminescent centre. Optically stimulated luminescence (OSL) was observed when stimulated by 470 nm blue light.Electron spin resonance (ESR) studies were carried out to identify the defect centres responsible for the TL and OSL processes in MgAl₂O₄:Tb³⁺. Two defect centres were identified in irradiated MgAl₂O₄:Tb³⁺ phosphor by ESR measurements which was carried out at room temperature and these were assigned to V and F⁺ centres. V centre (hole centre) is correlated to 120 and 220 °C TL peaks and F⁺ centre (electron centre), which acts as a recombination centre is correlated to 120, 220 and 340 °C.     

Indentation studies on 〈1 0 0〉, 〈0 0 1〉 and 〈1 0 1〉 face of ammonium dihydrogen phosphate (ADP) single crystals: A novel nonlinear optical material

In the present work, Vickers microhardness measurements were carried out on different faces i.e. (1 0 0), (0 0 1) and (1 0 1) of ammonium dihydrogen phosphate (ADP) single crystals grown by slow evaporation solution technique at room temperature in the load ranging from 0.2 to 2 N. The obtained results show that the load independent hardness values are 0.8, 0.7 and 0.66 GPa, respectively at different faces of ADP crystal. From the crack length measurements, the fracture toughness values (K_c) was estimated using Evans and Anstis model and the present studies suggest that Evans model is more relevant when compared to Anstis model. The load variation of some mechanical properties viz. brittle index number (B_i) and yield strength (σ_y) for ADP have also been calculated for the first time.     

Effect of Mn on the magnetic properties of Fe3B/Nd2Fe14B nanocomposites

The magnetic properties of Nd_4.5Fe_77−xMn_xB_18.5 (x=0, 1 and 2) nanocomposites prepared by the crystallization of amorphous precursors were investigated. Addition of Mn is found to decrease the crystallization temperature of the amorphous ribbons. The intrinsic coercivity _iH_c and maximum energy product (BH)_max increase from 2.6 kOe and 9.1 MGOe for x=0 to 3.1 kOe and 10.3 MGOe for x=1, respectively, and the remanence ratio M_r/M_s increases from 0.70 to 0.72. The effect of Mn on Curie temperature T_C and the thermal stability of M_r and _iH_c were also studied. ⁵⁷Fe Mössbauer spectra have been recorded for x=0, 1 and 2 ribbons at room temperature and site preference of the Mn atoms in Fe₃B and Nd₂Fe₁₄B phases is discussed using the Mössbauer spectroscopy.     

Cathode-sheath driven low-speed aerodynamic flow actuation using direct-current surface glow discharges

Flow actuation by a continuous/pulsed, direct-current (DC) surface glow discharge is explored. The discharge comprises an array of pin electrode pairs flush mounted on a dielectric actuator surface that lies adjacent to stagnant air. Strong electrostatic fields produced in the cathode sheath region of the discharge provides a motive force on the ions which in turn drag the background gas resulting in directed air flow from the anode to the cathode. The induced flow velocity is estimated by particle image velocimetry (PIV) at 10 Hz with TiO₂ seeding. For a pulsed DC discharge with peak power of 5 W per electrode pair, the induced flow velocity reaches peak values of about 1.7 m/s which is comparable to dielectric-barrier discharge (DBD) or corona discharge actuators. The actuation effect quantified by the magnitude of induced velocity increases as the pulse frequency increases from 0 to 1 kHz. The actuation effect decreases for further increase in frequency above 1 kHz. Decreased actuation effect at high frequency is accompanied by structural change in the discharge. At fixed frequency of 1 kHz, flow actuation effect is highest for a square wave pulse with a duty cycle of 50% indicating that pulsed DC discharges produces better actuation than continuous DC with a corresponding reduction in energy consumption.     

Electrostatic discharge sensitivity and electrical conductivity of composite energetic materials

Composite energetic material response to electrical stimuli was investigated and a correlation between electrical conductivity and ignition sensitivity was examined. The composites consisted of micrometer particle aluminum combined with another metal, metal oxide, or fluoropolymer. Of the nine tested mixtures, aluminum (Al) with copper oxide (CuO) was the only mixture to ignite by electrostatic discharge. Under the loose powder conditions of these experiments, the Al–CuO minimum ignition energy (MIE) is 25 mJ and exhibited an electrical conductivity two orders of magnitude higher than the next composite. This study showed a similar trend in MIE for ignition triggered by a discharged spark compared with a thermal hot wire source.     

Single-Phase Convective Heat Transfer of Water and Aqua Ethylene Glycol Mixture in a Small-Diameter Tube

A tailor-made convective heat transfer test facility is constructed to study the single-phase convective heat transfer of deionized water and 30 vol% and 60 vol% aqua–ethylene glycol in a stainless steel tube of 4 mm in inner diameter and 1 m in length. The heat flux is varied between 1 and 4 kW·m^?2 and for mass flux ranging from 160 to 475 kg·m^?2 s^?1. The experiments were predominantly conducted only for laminar flow regime. Finally, the heat transfer coefficient is recorded and compared with the conventional theories. It is observed that the presence of ethylene glycol in water decreases the heat transfer coefficient by more than 50%, due to the decreased Reynolds number and thermal conductivity of the mixture.     

Unified approach to photo-and electro-production of mesons with arbitrary spins

A new approach to identify the independent amplitudes along with their partial wave multipole expansions, for photo-and electro-production is suggested, which is generally applicable to mesons with arbitrary spin-parity. These amplitudes facilitate direct identification of different resonance contributions.      

A class of deformational flow test cases for linear transport problems on the sphere

A class of new benchmark deformational flow test cases for the two-dimensional horizontal linear transport problems on the sphere is proposed. The scalar field follows complex trajectories and undergoes severe deformation during the simulation; however, the flow reverses its course at half-time and the scalar field returns to its initial position and shape. This process makes the exact solution available at the end of the simulation, and facilitates assessment of the accuracy of the underlying transport scheme. A procedure to eliminate possible cancellations of errors when the flow reverses is proposed.     

Biphasic kinetic investigations on the evaluation of non-salt forming reductants for Pu(IV) stripping from tributyl phosphate and N,N-dihexyl octanamide solutions in n-dodecane

The relative stability of different oxidation states of actinide elements is influenced by the nature of complexes formed and redox equilibria in aqueous/non-aqueous solutions. The reduction/stripping studies on Pu(IV) ions from loaded organic phases of 1.1 M tributyl phosphate and of 1.1 M N,N-dihexyl octanamide in n-dodecane were studied using organic soluble tert-butyl hydroquinone (TBH) and aqueous soluble reductants like acetaldoxime (AX) and hydroxyurea (HU). These studies were carried out as a function of reductant and nitric acid concentration (0.5–4 M HNO₃) and of time. The changes in Pu oxidation states were followed by spectrophotometry for TBH and by distribution ratio values for AX and HU as reductants. Spectrophotometric investigations using TBH as reductant showed that it was desirable to strip Pu(III) formed after reduction of Pu(IV) in the organic phase, which may otherwise be reconverted to extractable Pu(IV) by in situ generated HNO₂ from oxidative degradation of TBH to tert-butyl quinone. Similarly, the biphasic reduction/stripping of Pu(IV) using AX and HU as reductant rate was affected adversely with increased aqueous phase acidity. This data will help in the accurate simulation of Pu separation processes using these reductants in mixer-settlers/pulsed columns or centrifugal contactors.     

Syntheses of β- and γ-fluorophenyl cis- and trans-α-methylene-γ-butyrolactones

Preparation of a series of cis-γ-fluorophenyl-β-phenyl-α-methylene-γ-butyrolactones is reported via ‘allylboration’ of fluorobenzaldehydes with (E)-methyl 3-phenyl-2-((4,4,5,5-tetramethyl-1,3,2-dioxaborolan-2-yl)methyl)acrylate. The corresponding trans-γ-fluorophenyl lactones were prepared either (i) via ‘allylboration’ using the (Z)-reagents or (ii) via an indium triflate-mediated isomerization of the cis-products. The difficulty in isomerizing difluorinated cis-products confirms the probable intermediacy of carbocations. Finally, the synthesis of cis-β-fluorophenyl-γ-phenyl-α-methylene-γ-butyrolactones was achieved via an indium-catalyzed allylation–lactonization of aldehydes with (Z)-2-(bromomethyl)-3-(fluorophenyl)acrylates.