Analytical determination of specific 4,4′-methylene diphenyl diisocyanate hemoglobin adducts in human blood

4,4′-Methylene diphenyl diisocyanate (MDI) is one of the most important isocyanates in the industrial production of polyurethane and other MDI-based synthetics. Because of its high reactivity, it is known as a sensitizing agent, caused by protein adducts. Analysis of MDI is routinely done by determination of the nonspecific 4,4′-methylenedianiline as a marker for MDI exposure in urine and blood. Since several publications have reported specific adducts of MDI and albumin or hemoglobin, more information about their existence in humans is necessary. Specific adducts of MDI and hemoglobin were only reported in rats after high-dose MDI inhalation. The aim of this investigation was to detect the hemoglobin adduct 5-isopropyl-3-[4-(4-aminobenzyl)phenyl]hydantoin (ABP-Val-Hyd) in human blood for the first time. We found values up to 5.2 ng ABP-Val-Hyd/g globin (16 pmol/g) in blood samples of workers exposed to MDI. Because there was no information available about possible amounts of this specific MDI marker, the analytical method focused on optimal sensitivity and selectivity. Using gas chromatography–high-resolution mass spectrometry with negative chemical ionization, we achieved a detection limit of 0.02 ng ABP-Val-Hyd/g globin (0.062 pmol/g). The robustness of the method was confirmed by relative standard deviations between 3.0 and 9.8 %. Combined with a linear detection range up to 10 ng ABP-Val-Hyd/g globin (31 pmol/g), the enhanced precision parameter demonstrates that the method described is optimized for screening studies of the human population.     

Single‐electron transfer‐living radical polymerization of oligo(ethylene oxide) methyl ether methacrylate in the absence and presence of air

The efficient Cu(0) wire‐catalyzed single‐electron transfer‐living radical polymerization (SET‐LRP) of oligo(ethylene oxide) methyl ether methacrylate (OEOMA) in DMSO and binary mixtures of DMSO with H₂O is reported. Addition of 10–80% H₂O to DMSO resulted in an increase in the apparent rate constant of propagation ( ), corresponding to an increase in the polarity and extent of disproportionation. At higher H₂O content, decreases, and in H₂O is slightly lower than that in DMSO. This unexpected behavior was attributed to the physical inaccessibility of Cu(0) wire catalyst to the hydrophobic reactive centers of OEOMA and initiator which self‐assemble in H₂O into micellar aggregates and vesicles. This hypothesis was confirmed by the faster polymerization in H₂O than in DMSO during catalysis with Cu(0) nanoparticles generated by disproportionation of CuBr. SET‐LRP of OEOMA can be performed in protic and dipolar aprotic solvents in air by the addition of hydrazine hydrate. The polymerization exhibited no induction period and identical as in the degassed experiment, and led to polymers with narrow molecular weigh distribution. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 3110–3122     

Gadolinium(III)‐Hydroxy Ladders Trapped in Succinate Frameworks with Optimized Magnetocaloric Effect

Two kinds of inorganic gadolinium(III)‐hydroxy “ladders”, [2×n] and [3×n], were successfully trapped in succinate (suc) coordination polymers, [Gd₂(OH)₂(suc)₂(H₂O)]_n ? 2n H₂O ( 1 ) and [Gd₆(OH)₈(suc)₅(H₂O)₂]_n ? 4n H₂O ( 2 ), respectively. Such coordination polymers could be regarded as alternating inorganic–organic hybrid materials with relatively high density. Magnetic and heat capacity studies reveal a large cryogenic magnetocaloric effect (MCE) in both compounds, namely (ΔH=70 kG) 42.8 J kg^?1 K^?1 for complex 1 and 48.0 J kg^?1 K^?1 for complex 2 . The effect of the high density is evident, which gives very large volumetric MCEs up to 120 and 144 mJ cm^?3 K^?1 for complexes 1 and 2 , respectively.     

Simulation of nuclide migration in a middle- and low-level radioactive waste repository based on GMS

Journal of Radioanalytical and Nuclear Chemistry - Groundwater is the most important factor contributing to the diffusion and migration of radionuclides in the repository. In this paper, the...     

Reversible Photoinduced Conversion of Unprecedented Norbornadiene-Based Photoswitches with Redox-Active Naphthalene Diimide Functionalities

An unprecedented compound class of functional organic hybrids consisting of a photoswitchable norbornadiene building block and a redoxactive chromophore, namely naphthalene diimide, were designed and synthesized. Within these structures the capability of rylene chromophores to function as a redox active catalyst upon their photoexcitation was utilized to initiate the oxidative back-conversion of the in situ formed quadricyclane unit to its norbornadiene analogue. In this way successive photoexcitation at two different wavelengths enabled a controlled photoswitching between the two isomerical states of the hybrids. Beyond this prove of concept, the dependency of the reaction rate to the intramolecular distance of the two functional molecular building blocks as well as the concentration of the photoexcited sample was monitored. The experimental findings and interpretations were furthermore supported by quantum chemical investigations.     

Enhanced Crystal Quality of Perovskite via Protonated Graphitic Carbon Nitride Added in Carbon-Based Perovskite Solar Cells

The quality of perovskite layers has a great impact on the performance of perovskite solar cells (PSCs). However, defects and related trap sites are generated inevitably in the solution-processed polycrystalline perovskite films. It is meaningful to reduce and passivate the defect states by incorporating additive into the perovskite layer to improve perovskite crystallization. Here an environmental friendly 2D nanomaterial protonated graphitic carbon nitride (p-g-C\begin{document}$_3$\end{document}N\begin{document}$_4$\end{document}) was successfully synthesized and doped into perovskite layer of carbon-based PSCs. The addition of p-g-C\begin{document}$_3$\end{document}N\begin{document}$_4$\end{document} into perovskite precursor solution not only adjusts nucleation and growth rate of methylammonium lead tri-iodide (MAPbI\begin{document}$_3$\end{document}) crystal for obtaining flat perovskite surface with larger grain size, but also reduces intrinsic defects of perovskite layer. It is found that the p-g-C\begin{document}$_3$\end{document}N\begin{document}$_4$\end{document} locates at the perovskite core, and the active groups -NH\begin{document}$_2$\end{document}/NH\begin{document}$_3$\end{document} and NH have a hydrogen bond strengthening, which effectively passivates electron traps and enhances the crystal quality of perovskite. As a result, a higher power conversion efficiency of 6.61% is achieved, compared with that doped with g-C\begin{document}$_3$\end{document}N\begin{document}$_4$\end{document} (5.93%) and undoped one (4.48%). This work demonstrates a simple method to modify the perovskite film by doping new modified additives and develops a low-cost preparation for carbon-based PSCs.     

Ultrahigh-intensity optical slow-wave structure

We report the development of corrugated "slow-wave" plasma guiding structures with application to quasiphase-matched direct laser acceleration of charged particles and generation of a wide spectrum of electromagnetic radiation. These structures support guided propagation at intensities up to 2 x 10(17) W/cm(2), limited by our current laser energy and side leakage. Hydrogen and argon plasma waveguides up to 1.5 cm in length with corrugation period as short as 35 microm are generated in a cryogenic cluster jet. Experimental data are consistent with simulations showing periodic modulations of the laser pulse intensity.     

Synergic Enhancement of High-density Polyethylene through Ultrahigh Molecular Weight Polyethylene and Multi-flow Vibration Injection Molding: A Facile Fabrication with Potential Industrial Prospects

General-purpose plastics with high strength and toughness have been in great demand for structural engineering applications. To achieve the reinforcement and broaden the application scope of high-density polyethylene(HDPE), multi-flow vibration injection molding(MFVIM) and ultrahigh molecular weight polyethylene(UHMWPE) are synergistically employed in this work. Herein, the MFVIM has better shear layer control ability and higher fabrication advantage for complex parts than other analogous novel injection molding technologies reported.The reinforcing effect of various filling times and UHMWPE contents as well as the corresponding microstructure evolution are investigated.When 5 wt% UHMWPE is added, MFVIM process with six flow times thickens the shear layer to the whole thickness. The tensile strength and modulus increase to 2.14 and 1.39 times, respectively, compared to neat HDPE on the premise of remaining 70% impact strength. Structural characterizations indicate that the enhancement is attributed to the improvement of shish-kebab content and lamellae compactness, as well as related to the corresponding size distributions of undissolved UHMWPE particles. This novel injection molding technology with great industrial prospects provides a facile and effective strategy to broaden the engineering applications of HDPE materials. Besides, excessive UHMWPE may impair the synergistic enhancement effect, which is also reasonably explained.     

Determination of phthalate esters in liquor samples by vortex‐assisted surfactant‐enhanced‐emulsification liquid–liquid microextraction followed by GC–MS

A novel method using vortex‐assisted surfactant‐enhanced‐emulsification liquid–liquid microextraction has been developed for the extraction of phthalate esters (PAEs) in Chinese liquor samples prior to analysis by GC–MS. In the proposed method, a high‐density extraction solvent (carbon tetrachloride) was dispersed into samples with the aid of a surfactant (Triton X‐100) and vortex agitation, resulting in a short extraction equilibrium (30 s). After centrifugation, a single microdrop of solvent was easily collected for GC–MS analysis. Key factors that affected the extraction efficiency were optimized. Under the optimum conditions, linearity was found in the range from 0.05 to 50 μg/L. Coefficients of determination varied from 0.9938 to 0.9971. LODs, based on an S/N of 3, ranged from 4.9 to 13 ng/L. Enrichment factors varied from 140 to 184. Reproducibility and recoveries were assessed by testing a series of three liquor samples that were spiked with different concentration levels. Finally, the proposed method was successfully applied to the determination of PAEs in 16 Chinese liquor samples. In this work, high‐density‐solvent vortex‐assisted surfactant‐enhanced‐emulsification liquid–liquid microextraction was applied for the first time for the extraction of PAEs in Chinese liquor samples and was proved to be simple, rapid, and sensitive.