Improvement of Biological Effects of Root-Filling Materials for Primary Teeth by Incorporating Sodium Iodide

Therapeutic iodoform (CHI₃) is commonly used as a root-filling material for primary teeth; however, the side effects of iodoform-containing materials, including early root resorption, have been reported. To overcome this problem, a water-soluble iodide (NaI)-incorporated root-filling material was developed. Calcium hydroxide, silicone oil, and NaI were incorporated in different weight proportions (30:30:X), and the resulting material was denoted DX (D5~D30), indicating the NaI content. As a control, iodoform instead of NaI was incorporated at a ratio of 30:30:30, and the material was denoted I30. The physicochemical (flow, film thickness, radiopacity, viscosity, water absorption, solubility, and ion releases) and biological (cytotoxicity, TRAP, ARS, and analysis of osteoclastic markers) properties were determined. The amount of iodine, sodium, and calcium ion releases and the pH were higher in D30 than I30, and the highest level of unknown extracted molecules was detected in I30. In the cell viability test, all groups except 100% D30 showed no cytotoxicity. In the 50% nontoxic extract, D30 showed decreased osteoclast formation compared with I30. In summary, NaI-incorporated materials showed adequate physicochemical properties and low osteoclast formation compared to their iodoform-counterpart. Thus, NaI-incorporated materials may be used as a substitute for iodoform-counterparts in root-filling materials after further (pre)clinical investigation.     

大模场面积光子晶体光纤激光器展宽脉冲锁模域的束缚态运转

实验研究了大模面积光子晶体光纤飞秒激光器在近零色散点展宽脉冲锁模的束缚态运转.获得了双脉冲束缚态锁模,以及脉冲间隔不相等的多脉冲束缚态锁模,实验发现束缚态的子脉冲间距具有随机性.通过建立光纤锁模激光器的数值模型,分析了激光器束缚态锁模建立的动力学过程,在一定抽运强度下,激光器存在多个稳态,或者单脉冲运转,或者子脉冲间隔不相等的束缚态运转,这取决于锁模建立阶段半导体可饱和吸收镜(SESAM)对噪声信号的随机提取.并提出了抑制束缚态的方法,模拟得出此项技术可直接获得的最大单脉冲能量为19.6 nJ,考虑到40%左右的压缩损耗,可得到压缩至76 fs的最短脉冲,单脉冲能量为11.8 nJ.数值模拟结果能很好的与实验相符合.     

Versatile Graphene-Isolated AuAg-Nanocrystal for Multiphase Analysis and Multimodal Cellular Raman Imaging

Main observation and conclusion Surface-enhanced Raman spectroscopy(SERS)-based bioanalytical technique involves the interaction of SERS-active substrate with c...     

Klein–Nishina Effect and the Cosmic Ray Electron Spectrum

Radiative energy losses are very important in regulating the cosmic ray electron and/or positron(CRE) spectrum during their propagation in the Milky Way. Particularly, the Klein–Nishina(KN) effect of the inverse Compton scattering(ICS) results in less efficient energy losses of high-energy electrons, which is expected to leave imprints on the propagated electron spectrum. It has been proposed that the hardening of CRE spectra around 50 GeV observed by Fermi-LAT, AMS-02, and DAMPE could be due to the KN effect. We show in this work that the transition from the Thomson regime to the KN regime of the ICS is actually quite smooth compared with the approximate treatment adopted in some previous works. As a result, the observed spectral hardening of CREs cannot be explained by the KN effect. It means that an additional hardening of the primary electrons spectrum is needed. We also provide a parameterized form for the accurate calculation of the ICS energy-loss rate in a wide energy range.     

Highly efficient toughening effect of ultrafine full-vulcanized powdered rubber on poly(lactic acid)(PLA)

A unique ultrafine full-vulcanized powdered ethyl acrylate rubber (EA-UFPR) was used as the toughening modifier for poly (lactic acid) (PLA). Largely improved tensile toughness was successfully achieved with the incorporation of only 1 wt% EA-UFPR, while the tensile strength and modulus of the blends were almost the same as pure PLA. The highly efficient toughening of PLA by UFPR is mainly ascribed to the strong interfacial interaction between PLA and UFPR and good dispersion of UFPR particles in PLA matrix. Our work provides an effective toughening method to largely improve the mechanical properties of PLA without sacrificing its stiffness, which is very important for the wide application of PLA materials.     

Hierarchical nanostructured composite cathode with carbon nanotubes as conductive scaffold for lithium-sulfur batteries

Carbon nanotubes (CNTs) are excellent scaffolds for advanced electrode materials, resulting from their intrinsic sp2 carbon hybridization, interconnected electron pathway, large aspect ratio, hierarchical porous structures, and low cost at a large-scale production. How to make full utilization of the mass produced CNTs as building blocks for nanocomposite electrodes is not well understood yet. Herein, a composite cathode containing commercial agglomerated multi-walled CNTs and S for Li-S battery was fabricated by a facile melt-diffusion strategy. The hierarchical CNT@S coaxial nanocables exhibited a discharging capacity of 1020 and 740 mAh g-1 at 0.5 and 2.0 C, respectively. A rapid capacity decay of 0.7% per cycle at the initial 10 cycles and a slow decay rate of 0.14% per cycle for the later 140 cycles were detected. Such hierarchical agglomerated CNT@S cathodes show advantages in easy fabrication, environmentally benign, low cost, excellent scalability, and good Li ion storage performance, which are extraordinary composites for high performance Li-S battery.     

Clicked (AB)2C‐type miktoarm terpolymers: Synthesis,thermal and self‐assembly properties,and preparation of nanoporous materials

A well‐defined (PEO‐PS)₂‐PLA miktoarm terpolymer ( 1 ) was synthesized by stepwise click reactions of individually prepared poly(ethylene oxide) (PEO), polystyrene (PS, polymerized by atom transfer radical polymerization), and polylactide (PLA, polymerized by ring‐opening polymerization) blocks. As characterized by differential scanning calorimetry and small‐angle X‐ray scattering techniques, the terpolymer self‐assembled into a hexagonal columnar structure consisting of PLA/PEO cylindrical cores surrounded by PS chains. In contrast, the ion‐doped sample ( 1‐Li⁺ ) with lithium concentration per ethylene oxide = 0.2 exhibited a three‐phase lamellar structure, which was attributed to the microphase separation between PEO and PLA blocks and to the conformational stabilization of the longest PLA chain. The two‐phase columnar morphology before the ion doping was used to prepare a nanoporous material. PLA chains in the cylindrical core region were hydrolyzed by sodium hydroxide, producing nanopores with a pore diameter of about 14 nm. The resulted nanoporous material sank to the bottom in water, because of water‐compatible PEO chains on the walls. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Cooling-induced increase of methane cluster size investigated under a Coulomb explosion scheme

In this letter, we discuss the increase in the average cluster size by lowering the stagnation temperature of the methane （CH4） gas. The Coulomb explosion experiments are conducted to estimate the cluster size and the size distribution. The average CH4 cluster sizes Nay of 6 230 and 6 580 are acquired with the source conditions of 30 bars at 240 K and 60 bars at 296 K, respectively. Empirical estimation suggests a five-fold increase in the average size of the CH4 clusters at 240 K compared with that at room temperature under a backing pressure of 30 bars. A strong nonlinear Hagena parameter relation （Г^＊∝ T0^-3.3） for the CH4 clusters is revealed. The results may be favorable for the production of large-sized clusters by using gases at low temperature and high back pressures.     

厄尔尼诺和南方涛动海气耦合模型中参数估计的变分方法

提出一种基于变分原理估计厄尔尼诺和南方涛动海气耦合模型中未知参数的方法. 首先将所研究的非线性海气耦合动力方程引入到目标泛函中; 接着利用变分方法导出伴随方程和待辨识参数泛函梯度的公式; 然后设计了估计未知参数的算法.数值试验结果表明变分方法是一 种能有效估计海气耦合非线性系统未知参数的方法.