Developing a hybrid emulsion polymerization system to synthesize Fe3O4/polystyrene latexes with narrow size distribution and high magnetite content

A hybrid emulsion polymerization was formulated for synthesizing Fe₃O₄/polystyrene composite latex. This system, containing binary droplets that are magnetic (Mag)‐droplets with a diameter of 100–200 nm and styrene (St)‐droplets with a diameter of 3–4 μm, was obtained by mixing Mag‐miniemulsion and St‐macroemulsion. With extremely low surfactants concentration (?critical micelle concentration, CMC), the nucleated loci are selectively controlled in the Mag‐droplets, as the result of smaller droplet size and larger surface ratio. Both water‐soluble potassium persulfate (KPS) and oil‐soluble 2,2′‐azobis(2‐isobutyronitrile) was adopted to initiate the polymerization. In the presence of KPS, magnetic polystyrene latices with particles size of 60–200 nm, narrow size distribution, and high magnetite content (86 wt % measured by TGA) were attained successfully. The synthesized magnetic Fe₃O_4/polystyrene latices assembled into well‐ordered hexagonal structure in the surface of a carbon supported copper grid. The influence of various parameters on various aspects of the as‐synthesized Fe₃O₄/polystyrene was investigated in detail: type of initiator on composite morphology, feed ratio of Mag‐miniemulsion and St‐macroemulsion on magnetite content, and hydrophobic agent or amount of surfactant on size and size distribution. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5285–5295, 2007     

A combined mixed and discontinuous Galerkin method for compressible miscible displacement problem in porous media

In this paper, we present a numerical scheme for solving the coupled system of compressible miscible displacement problem in porous media. The flow equation is solved by the mixed finite element method, and the transport equation is approximated by a discontinuous Galerkin method. The scheme is continuous in time and a priori hp error estimates is presented.     

Simulation and fabrication of carbon nanotubes field emission pressure sensors

A novel field emission pressure sensor has been achieved utilizing carbon nanotubes (CNTs) as the electron source. The sensor consists of the anode sensing film fabricated by wet etching process and multi-wall carbon nanotubes (MWNTs) cathode in the micro-vacuum chamber. MWNTs on the silicon substrate were grown by thermal CVD. The prototype pressure sensor has a measured sensitivity of about 0.17-0.77 nA/Pa (101-550 KPa). The work shows the potential use of CNTs-based field-emitter in microsensors, such as accelerometers and tactile sensors.     

光纤放大器增益饱和对有源光纤环形腔滤波特性的影响

从理论和实验两个方面研究了有源光纤环形腔滤波器输入光功率对光纤放大器增益的影响及由此引起的对有源光纤环形腔滤波特性的影响。在考虑上述影响的情况下 ,对有源光纤环形腔滤波器参数的优化作了讨论     

江汉平原上空QTEC变化特征的统计分析

提出了一种观测台网用多接收机性能一致性的标定方法，并利用江汉平原GPS接收台网的观测数据，分析了该地区上空QTEC的日变化、季节变化、年变化和逐年变化的统计特征．标定结果表明，不同接收机之间的仪器偏差是从双频GPS卫星信标推算QTEC的主要误差来源之一，必须校正．统计分析证实，江汉平原上空QTEC的日变化特征同时受电离层和等离子层控制，其年变化以半年周期为主，峰值和谷值分别出现在两分点和两至点附近，QTEC值的逐年变化从太阳活动峰年到低年逐年下降，与以太阳黑子数为代表的太阳活动密切相关．     

MODIS通道1和通道2大气订正的一种快速实用方法

提出了利用气象资料对MODIS影像进行大气校正的一种快速实用方法.读取MODIS前两个通道250min的反射率,采用常用的黑色目标扣除法(Dark-object subtraction)计算天空程辐射,通过卫星过境时刻的气象能见度和水汽资料计算大气透过率,最后推导出目标物的反射率.通过比较两个邻近日期MODIS影像校正前后的归一化植被指数(NDVI)值,得出利用本文提出的方法对MODIS进行大气校正所得到的NDVI值更接近实际情况.结果表明:利用气象能见度和水汽压可以对MODIS数据进行快速有效的大气校正.     

Multi-objectives fuzzy models for designing 3D trajectory in horizontal wells

In this paper, multi-objective models for designing 3D trajectory of horizontal wells are developed in a fuzzy environment. Here, the objectives of minimizing the length of the trajectory and the error of entry target point are fuzzy in nature. Some parameters, such as initial value, end value, lower bound and upper bound of the curvature radius, tool-face angle and the are length of each curve section, are also assumed to be vague and imprecise. The impreciseness in the above objectives have been expressed by fuzzy linear membership functions and that in the above parameters by triangular fuzzy numbers. Models have been solved by the fuzzy non-linear programming method based on Zimmermann [1] and Lee and Li [2]. Models are applied to practical design of the horizontal wells. Numerical results illustrate the accuracy and efficiency of the fuzzy models.