Time-dependent density functional theory calculations of the photoabsorption of fluorinated alkanes

Time-dependent density functional theory (TD-DFT) calculations of the transition energies and oscillator strengths of fluorinated alkanes have been performed. The TD-DFT method with the non-local B3LYP potential yields transition energies for the methanes, which are smaller by about 10% as compared to the experimental values. An empirical linear correlation was found between the calculated and experimental transition energies both at the B3LYP/DZ+Ryd(C, F) and B3LYP/cc-pVTZ+Ryd(C, F, H) levels for a total of 19 transitions of the fluorinated methanes with linear correlation coefficients of 0.987 for the former and 0.988 for the latter. This empirical correlation for fluorinated methane molecules is found to agree well with the previously obtained empirical correlations between calculated and experimental values for non-fluorinated molecules. The results show that a single empirical-correlation relationship can be used for both non-fluorinated and fluorinated molecules to predict transition energies. This linear relationship is then used to predict the photoabsorption spectra of ethane, propane, butane, and partially and fully fluorinated derivatives. A key result of these calculations is the dominance of Rydberg transitions in the spectral region of interest.     

Melting behavior of highly stretched isotactic polypropylene film

Isotactic polypropylene film was stretched in poly(ethylene glycol) at 140°C and its melting behavior was investigated by using a differential scanning calorimeter (DSC-1B). The shape of the melting curve depends largely on the stretching ratio, v. A sample stretched to moderate extension (1 < v < 3.5–4) has only a single melting peak (163°C) in the thermogram. When the sample is stretched beyond v = 3.5–4, the thermogram becomes more and more complex with increase of v, and some peaks appear when stretched to 10 < v < 13. The lowest peak which is considered to be the melting peak of the intermolecular crystals produced by the unfolding of chain molecules in the lamellae develops gradually with increase of v. In the thermogram for v = 18 the lowest temperature peak is most pronounced, in contrast to the highest temperature peak which decreases markedly in intensity. The phenomenon shows that large amounts of lamellar crystals are converted to intermolecular crystals in this region. On further stretching (v > 20) a very sharp high temperature peak appears, whose half-width is about 1°C. Qualitatively similar results were obtained for the samples stretched in poly(ethylene glycol) at 150°C and in air at 140 and 150°C.     

Tumor cell detection method using complement-mediated cytolytic reaction and imaging sensor system

A novel tumor-detection system consisting of complementmediated cytolytic reaction and an image processing system was developed for the simple and rapid determination of tumor cells. The present system consists of a CCD image sensor, image memory board, personal computer, and microscope. When monoclonal antibody 3C4, which is specific to the guinea pig hepatoma L-10, was added to cell suspension, only L-10 cytolysis occurred. Cytolysis caused a decrease in brightness of the cells observed by phase-contrast microscopy. The phase contrast image of the cells before cytolysis was converted to a digitalized signal and stored in computer memory. After cytolysis, a brightness threshold above that of lysed cells was subtracted from the digitalized signal and compared to the signal stored before reaction. L-10 cells in mixed cell suspension were determined specifically by the system. Measurement time was only 2 sec and overall time, including reaction time, was approximately 30 min. Since this method does not require a cell washing process, automation of the whole system is possible.     

High modulus polyimide/polyimide molecular composite films that utilize acetylene unit as a crosslink site

Polyimide/polyimide molecular composite (MC) films comprised of a rigid polyimide derived from biphenyltetracarboxylic dianhydride (BPDA) and p-phenylenediamine (PDA) and a flexible polyimide derived from BPDA and bis (3,3'-diaminodiphenyl) acetylene (intA) and/or oxydianiline (ODA) were prepared by blending the polyamic acid solutions in 7 : 3 weight ratio, and then imidizing the blend films. Acetylene content in the flexible polyimide backbone was controlled by the ratio of intA and ODA. Cold-drawing of the blend polyamic acid films, followed by imidization, gives high modulus polyimide/polyimide MC films. The modulus of the MC films increased almost linearly with the draw ratio, reaching 25.5 GPa for the 40% drawn film. Acetylene groups in the flexible polyimide can be thermally cured to crosslink. The onset of exotherm appeared at 340°C on DSC, reaching maximum at 398°C. After the thermal crosslinking, the MC films maintained the high modulus, though elongation became small. Taking advantage of the crosslinkable acetylene units, two MC films were laminated and processed at 400°C for 20 min under 100 kg/cm² to give a good-quality laminate film. The interface of the two films was strongly bonded through the crosslinking of acetylene groups. Laminate films maintained the high modulus afforded by the cold-drawing. © 1994 John Wiley & Sons, Inc.     

Synthesis, crystal structure and thermoelectric properties of a new carbide Zr2[Al3.56Si0.44]C5

A new quaternary layered carbide, Zr₂[Al_3.56Si_0.44]C₅, has been synthesized and characterized by X-ray powder diffraction, transmission electron microscopy and thermopower and electrical conductivity measurements. The crystal structure was successfully determined using direct methods, and further refined by the Rietveld method. The crystal is trigonal (space group R3m, Z=3) with lattice dimensions of a=0.331059(5), c=4.09450(5) nm and V=0.38864(1) nm³. The final reliability indices calculated from the Rietveld refinement were R_wp=6.24%, R_p=4.21% and R_B=0.82%. The crystal structure is composed of electroconductive NaCl-type ZrC slabs separated by Al₄C₃-type [Al_3.56Si_0.44]C₃ layers. This material had thermoelectric properties superior to those of the ternary layered carbides Zr₂Al₃C₄ and Zr₃Al₃C₅, with the power factor reaching 7.6×10⁻⁵W m⁻¹ K⁻².     

Characterization of flower-inducing compound in Lemna paucicostata exposed to drought stress

A flower-inducing compound, LDS1, was isolated from a free-floating aquatic plant, Lemna paucicostata. The chemical structure and the absolute stereochemistry of LDS1 were determined as (9R,13R,11E,15Z)-9,13-dihydroxy-10-oxooctadeca-11,15-dienoic acid for its most abundant diastereomer. LDS1 was enzymatically produced when the plant was exposed to drought stress, and induced flowering at a concentration of 10 nM.     

Cationic copolymerization of indene with styrene derivatives: Synthesis of random copolymers of indene with high molecular weight

Random copolymers with high molecular weights of indene and p‐methylstyrene (pMeSt) were synthesized by cationic polymerization with trichloroacetic acid/tin tetrachloride in CH₂Cl₂ at low temperatures. When indene and pMeSt (1:1 v/v), for example, were polymerized at ?40 °C, both monomers were consumed at very similar rates to give a copolymer with high molecular weight [number‐average molecular weight (M_n): 8–9 × 10⁴]. This is indeed quite unexpected behavior for the combination of these two monomers because pMeSt polymerized over 1000 times faster than indene in the homopolymerization under the reaction conditions previously described. The product copolymer of indene and pMeSt had a random monomer sequence in it that was confirmed by NMR analyses and thermal‐property measurements. In sharp contrast with pMeSt, styrene and p‐chlorostyrene, which have no electron‐donating groups on the phenyl ring, led to low molecular weight polymers (M_n < 10,000) in the copolymerization with indene (1:1 v/v). © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2449–2457, 2002     

Photoinduced rotational isomerization mechanism of 2-chlorobenzaldehyde in low-temperature rare-gas matrices by vibrational and electronic spectroscopies

Rotational isomerization of 2-chlorobenzaldehyde in low-temperature rare-gas matrices has been investigated by vibrational and electronic spectroscopies with aids of the density functional theory (DFT) and configuration interaction single (CIS) calculations. Infrared spectrum of the less stable O-cis isomer, produced from the more stable O-trans isomer upon UV irradiation, is measured with an FT-IR spectrophotometer. The enthalpy difference between the O-cis and O-trans isomers is estimated to be 9.7±0.2 kJ mol⁻¹ from the temperature dependence of the infrared band intensities. Analyses of the infrared and electronic absorption spectral changes after UV irradiation and the phosphorescence spectra measured at various excitation wavelengths suggest that the rotational isomerization occurs via the intersystem crossing from S₁ to T₁.