Effect of electric field strength and exposure time on epoxy and high density polyethylene measured by positron annihilation lifetime

Using the positron annihilation lifetime technique, the annihilation parameters have been measured for epoxy and high density polyethylene (HDPE) as a function of AC electric field strength and the exposure time. The lifetime spectra have been resolved into three components, the longest component (I₃₃) is attributed to the pick-off annihilation of o-Ps in the amorphous regions. The intermediate one (I₂₂) is due to the annihilation of free positrons, while the shorter component (I₁₁) stems from self annihilation of p-Ps. In HDPE, the o-Ps parameters ₃ andI ₃ are measured as a function of electric field strengths in the range from 10 to 100 kV/cm exposed for 24 hours. A decrease inI ₃ of 8% is observed from zero to 50 kV/cm followed by an increase of the same order from 50 to 100 kV/cm. By investigating the effect of the exposure time from 2 to 24 hours at 16 and 50 kV/cm, the effect is confirmed and is attributed to the inhibition of o-Ps formation at lower field strength. In epoxy, the effect or exposure time onI ₃ at 166 and 133 kV/cm shows a similar behavior as in HDPE. At 133 kV/cmI ₃ decreases by only 2.5%. On the other hand, the changes in ₃ occur at short exposure times. Again at large times the saturation is obtained. These effects are attributed to the expansion of free volume (increase of ₃) competing at longer exposure times with other phenomena, such as liberation of free radicals, which reduce the o-Ps intensityI ₃ through the conversion to p-Ps. The reactions between o-Ps and free radicals might also lead to free positrons, which could explain the increase ofI ₂ and the decrease of ₃ at longer exposure times.     

Determination of reducing end sugar residues in oligo- and polysaccharides by gas-liquid chromatography

Reducing end sugar residues in maltodextrins and arabinoxylans are determined as alditol acetates by gas-liquid chromatography following reduction, acid hydrolysis and acetylation of the samples. After this conversion to alditol acetates, the reducing end sugars are thus separated from their acetylated aldose counterparts. The method allows to identify individual reducing end sugars quantitatively and is a good alternative for colorimetric reducing sugar assays and 1H-NMR analysis. To demonstrate the advantages of the method, an application in a study of enzymic solubilisation and degradation of water unextractable arabinoxylan from a flour squeegee fraction is described.     

Elimination of methane from protonated acetaldehyde: The Ab initio transition state

The transition state (TS) for loss of CH₄ from protonated acetaldehyde has been located at the second-order Moller-Plesset (MP2)/6-31G(d,p) level of theory. The activation energy is predicted to be 263.9 kJ/mol starting from the more stable form (methyl and hydrogen E) and 261.6 kJ/mol starting from the less stable form (methyl and hydrogen Z) that is required for reaction. The products (methane and the formyl ion) are predicted to lie 136.6 kJ/mol below the TS for their formation. MP2 methods underestimate the heats of formation of both the TS and the reaction products by about 40 kJ/mol when compared with experiment. Restricted Hartree-Fock (RHF) calculations give much more accurate relative energies. The MP2 TS leads directly to fragmentation and is described as a protonation of the methyl group by the acidic proton on oxygen. Under RHF theory the reaction is stepwise. An RHF TS similar to the MP2 TS leads to a nonclassical intermediate (which is stable at this level of theory) that has one of the C---H bonds protonated. This mechanism (protonation of an alkyl group) appears to be a general one for high energy 1,2 eliminations from organic cations. (J Am Soc Mass Spectrom 1994, 5, 1102-1106)     

Amidinoethylation—a new reaction—IV : The amidinoethylation of alcohols: a facile synthesis of 3-alkoxy-N,N'-substituted-propanamidines

The amidinoethylation of alcohols takes place by the addition of sodium alkoxides 2 (R¹ = Me, Et) to the CC double bond of a variety of N,N'-substituted-propenamidines 1 (Method A). This illustrates the activation of the CC double bond by the conjugated amidine function and provides a new class of Michael acceptors for alcohols. However, this activation is poorer than with other nucleophiles or Michael acceptors. The amidinoethylation makes available 3-alkoxy-N,N'-substituted-amidines not easily accessible by other classical methods. However, it is demonstrated that the general N,N'-substituted-amidine synthesis via the nitrilium salts can also apply to nitrile compounds having an alkoxygroup present on the molecule (method B). Since the cyanoethylation of alcohols (4) is a very fast and facile reaction the method B is the preferred strategy for the synthesis of 3-alkoxy-N,N'-substituted-propanamidines 3.     

Fine characterization of the ethylene and ethane sorption in poly(amide 12-block-tetramethylenoxide) copolymer/AgBF4 membranes

Ethylene/ethane sorption characteristics were determined for dry Pebax™ (poly(amide 12-block-tetramethylenoxide) copolymer)/AgBF₄ membranes by using an electronic microbalance. The membranes containing 0.7 and 22 wt.% AgBF₄ showed a dual-mode sorption isotherm. The ethane isotherms for all the membranes were of the Henry-type, which is the normal sorption for gases in rubbery polymers. The abnormal presence of Langmuir sorption sites only for ethylene in the rubbery copolymer, never reported sofar, is attributed to the silver-based specific complexation sites. The silver salt which dissolved in limited amounts in the rubbery copolymer had a much smaller Langmuir sorption capacity than the salt that crystallized in the copolymer. The sorption kinetics indicate that the crystallized salt did adsorb slowly ethylene according to a zeroth-order kinetics, but not ethane. The gas uptake kinetics resulting from a step of the pressure surrounding the copolymer exhibited one stage for ethane but two stages for ethylene. For the latter, there was first a fast Fickian sorption stage, then a drift of the zeroth-order sorption of ethylene on salt crystals, which contributes for a large part to the total uptake. The zeroth-order sorption suggests that the sorbed ethylene amount in the second-stage is independent of the crystal-surface coverage. The value of the Fickian diffusion coefficient calculated by fitting the kinetics with a solution of the second Fick’s law was 5 × 10⁻¹² m²/s for both ethylene (the first stage) and ethane, and is typical for small organic compounds in a rubbery material.     

Thermal decompositions of N-methylpyridinium,quinolinium, isoquinolinium and phenanthridinium salts in a mass spectrometer. Evidence for a specific HI elimination and for an oxidation to amides

The mass spectra of some N-methylpyridinium, quinolinium, isoquinolinium and phenanthridinium salts (R⁺X^?)

1 The salt will be represented by R⁺X^? or RX, R⁺ being the organic moiety, with its associated mass and X- the inorganic anion.

are analyzed (X^? = I^? or ClO₄^?). For X^? = I^?, thermal decomposition gives rise mainly to the superimposed spectra of CH₃I and the free base. Hence, iodide salts cannot be determined specifically by their mass spectra. When an α-methyl group is present, e.g. 2-methylpyridinium methiodide, elimination of HI becomes an important thermal process. For X^? = ClO₄^?, the same pattern is observed, but in addition a generally important peak at [R + 15] is present. This peak is due to the oxidation, mainly α to the nitrogen of the organic moiety by the ClO₄^? ion, giving rise to the corresponding amide. In some cases, chlorination of the organic moiety has been observed as well as double oxidation. The thermal processes for the perchlorate salts are characteristic and are useful in the elucidation of the quaternary structure.     

Dispersion phenomena in reactors for flow analysis

Both coiled open tubular reactors and packed-bed reactors can be used in flow analysis. Band broadening and pressure drop in these reactors are discussed. Theoretical analysis shows that packed-bed reactors are to be preferred. It is shown that for a given residence time and equal band-broadening values the pressure drop over a packed-bed reactor is lower than over a coiled open tubular reactor. Rules for optimal design are given for coiled tubular reactors and packed-bed reactors. The application of both reactors is shown for the spectrophotometric determination of phosphate with a vanadomolybdate reagent yielding a yellow colour.     

Strategies for multi-site GLP studies

 A GLP study can be performed at more than one site. This is called a multi-site study. Although, the study is performed at different sites, it is still one study and must completely comply with the GLP principles. The fact that different activities are conducted at different sites implies that the planning, the organization and the communication are crucial for the success of the study. This means that all the staff involved should know their responsibilities and should have the knowledge and skills to realize all the phases of the study according to the GLP principles. To achieve a well managed multi-site study, several strategies for setting up such a study can be followed. This paper focuses on the responsibilities, communication, and collaboration of the personnel, which are involved in a multi-site study. Several case studies are highlighted, and we concluded that the basic communication triangle in a single-site GLP study between test facility management, study director, and the quality assurance unit should be extended to the communication among test facility and test site management, study director, principle investigator(s), and the quality assurance units at the test sites. Introduction Received: 14 August 2002 Accepted: 26 November 2002     

A microwave-assisted click chemistry synthesis of 1,4-disubstituted 1,2,3-triazoles via a copper(I)-catalyzed three-component reaction

A microwave-assisted three-component reaction was used to prepare a series of 1,4-disubstituted-1,2,3-triazoles from corresponding alkyl halides, sodium azide, and alkynes. This procedure eliminates the need to handle organic azides, as they are generated in situ, making this already powerful click process even more user-friendly and safe.