Metal-Support Interaction Which Controls the Oxidation State, Structure and Catalysis of Pd

A metal-support interaction between Pd and various kinds of zeolite and metal oxide supports was studied, which were active in the catalytic combustion and selective reduction of NO. The acid-base properties of supports affected the oxidation state, structure and catalytic activity of Pd. The acid sites of zeolite played the role to anchor the dispersed PdO as evidenced by the dynamic structural change of Pd. It was found that the metal-support interaction is an important factor, affecting the oxidation state, structure and catalytic performance of Pd.     

Determination of acetaldehyde in fuel ethanol by high-performance liquid chromatography with electrochemical detection.

The cyclic voltammetric behavior of acetaldehyde and the derivatized product with 2,4-dinitrophenylhydrazine (DNPHi) has been studied at a glassy carbon electrode. This study was used to optimize the best experimental conditions for its determination by high-performance liquid chromatographic (HPLC) separation coupled with electrochemical detection. The acetaldehyde-2,4-dinitrophenylhydrazone (ADNPH) was eluted and separated by a reversed-phase column, C18, under isocratic conditions with the mobile phase containing a binary mixture of methanol/LiCl(aq) at a concentration of 1.0 x 10(-3) M (80:20 v/v) and a flow rate of 1.0 mL min(-1). The optimum condition for the electrochemical detection of ADNPH was +1.0 V vs. Ag/AgCl as a reference electrode. The proposed method was simple, rapid (analysis time 7 min) and sensitive (detection limit 3.80 microg L(-1)) at a signal-to-noise ratio of 3:1. It was also highly selective and reproducible [standard deviation 8.2% +/- 0.36 (n = 5)]. The analytical curve of ADNPH was linear over the range of 3-300 mg L(-1) per injection (20 microL), and the analytical recovery was > 99%.     

Influence of the Solvent on the “Casting” Methodology for MWCNT‐Modified Glassy Carbon and Platinum Electrodes

The choice of electrode material and surface preparation method are usually dictated by the suitability of the electrode to observe an electrochemical parameter, such as heterogeneous electron transfer rate, surface coverage, or redox potential. Thus, the glassy carbon (GC) and platinum (Pt) electrodes were modified with multiwalled carbon nanotubes (MWCNT) by direct “casting” modification using nine different aliquots of solvents. After drying at room temperature, the modified electrode showed distinct redox peaks corresponding to ferrocyanide oxidation/reduction. Using chemometrics, the cyclic voltammograms with higher current intensity were obtained for those in which ethanol, water and acetone as dispersing agents were used for GCE and dimethylformamide, water and acetone for Pt electrode modification.     

Precise determination of bromine in PP resin pellet by instrumental neutron activation analysis using internal standardization

Instrumental neutron activation analysis with the internal standardization was applied to the precise determination of Br in polypropylene resin of candidate certified reference material. The known amount of ¹⁹⁷Au was used as an internal standard to compensate for neutron flux inhomogeneity, to improve the γ ray measurement uncertainty and the linearity of the calibration curves. The reliability of the proposed method validated using analytical results of BCR-681. The analytical result of Br in the sample was consistent with that obtained by ID-ICPMS. The relative expanded uncertainty (k = 2) was 1.5 %, and it was equivalent to that of ID-ICPMS.     

Effect of preparation process of microfibrillated cellulose-reinforced polypropylene upon dispersion and mechanical properties

Microfibrillated cellulose (MFC)-reinforced polypropylene (PP) was prepared via two engineering approaches: disintegration of the pulp by a bead mill followed by a melt-compounding process with PP (B-MFC-reinforced PP); and disintegration of the pulp mixed with PP by a twin screw extruder followed by a melt-compounding process (T-MFC-reinforced PP). The effects that the engineering process and the microfibrillation of the pulp had upon the dispersion and mechanical properties were investigated through tensile tests, rheological analysis and X-ray computed tomography. The bead-milling method enabled a uniform microfibrillation of the pulp to under 100 nm, which corresponded to a surface area of 133–146 m²/g for the pulp, found by the Brunauer–Emmett–Teller (BET) analysis. The T-MFC-reinforced PP with 30 wt% MFC content exhibited a tensile modulus of 5.3 GPa and a strength of 85 MPa, whereas the B-MFC-reinforced PP composites with the same content of MFC exhibited values of 4.1 GPa and 59.6 MPa, respectively. Rheological analysis revealed that the complex viscosity and storage modulus at 170 °C of T-MFC-reinforced PP with 30 wt% MFC content are 5–7 and 5–8 times higher than that of B-MFC-reinforced PP, respectively. This indicated that T-MFC was more dispersed in the PP than B-MFC. Therefore, T-MFC produced a more rigid interconnected network in the matrix during the melting state than B-MFC.     

Theoretical study on singlet oxygen adsorption onto surface of graphene-like aromatic hydrocarbon molecules

Recently, graphene sheet is one of interesting systems to realize novel electronic properties. Especially, interaction between graphene and adsorbed oxygen molecule is very important to control electronic condition. In this paper, we employed some aromatic hydrocarbons as simple systems of graphene sheet and ab initio MO calculations were carried out to investigate inter-molecular interaction. It is found that not triplet but singlet O₂ molecule have potential of chemisorption onto graphene surface. From the calculated potential energy surface (PES) for distance between benzene and O₂ molecules, meta-stable structure is found at about 1.5 Å with potential barrier. In the optimized structure of its meta-stable state, structural strain can be relaxed through bending of planer benzene ring. Its energy is estimated at 70.10 kcal/mol for benzene. We also estimated the strain effects for naphthalene and pyrene molecules as larger case of graphene and they were 80.85 and 72.45 kcal/mol, respectively.