亚细胞器诱导的2,4,6-三硝基甲苯阴离子自由基的ESR研究

本文在无氧条件下利用ESR分别观察了肝脏和晶状体的微粒体及线粒体酶在NADPH存在下还原三硝基甲苯(TNT)的过程,检测到参数为g=2.0048±0.0005,A_对位~N=1.215mT,A~N=0.800±0.010mT,A~H=0.122±0.0206mT的自由基信号,并通过电子计算机对ESR谱的模拟证明该自由基信号为TNT硝基阴离子自由基,根据其超精细分裂常数认为,其不配对电子的电子云密度主要分布在对位硝基上。     

Laser-induced breakdown of soda-lime glass microspheres using Nd:YAG laser

The Nd:YAG laser-induced breakdown of 20 μm glass microspheres was investigated using time-resolved optical shadow and Schlieren images. Time-resolved imaging showed the location of the initial breakdown and the shockwave motion over its first 400 μm of expansion. Measured shockwave velocities were in the range of 1–10 km/s and showed a linear dependency on laser fluence within 30 ns.     

Output dynamics and stabilisation of a multi-mode double-clad Yb-doped silica fibre laser

The intensity dynamics of the double-clad Yb fibre laser have been characterised. Stabilisation of the fibre laser intensity by using uniform bi-directional pumping is demonstrated. For the single-end-pumped Yb fibre laser, the output becomes more stable for the shorter fibre length due to the higher threshold of stimulated Brillouin scattering, SBS, and Kerr effects and the reduction of saturated absorber effects caused by any unpumped fibre section. By additional pumping in a double-end-pumped configuration, the output power can be scaled higher before detecting high intensity pulses initiated by SBS in the Yb fibre laser due to the reduction of saturable absorption effect. It is confirmed that uniform pumping enhances the stability of the laser output.     

Measurement of small-signal and large-signal responses of packaged laser modules at high temperature

In this paper, the pulsed injection method is extended to measure the chip temperature of various packaged laser modules, such as the DFB laser modules, the FP laser modules, and the EML laser modules. An optimal injection condition is obtained by investigating the dependence of the lasing wavelength on the width and period of the injection pulse in a relatively wide temperature range. The small-signal frequency responses and large-signal performances of packaged laser modules at different chip temperature are measured. The adiabatic small-signal modulation characteristics of packaged LD are first extracted. In the large-signal measurement, the effects of chip temperature, bias current and driving signal on the performances of the laser modules are discussed. It has been found that the large-signal performances of the EML modules depend on the different red-shift speeds of the DFB and EAM sections as chip temperature varying, and the optimal characteristics may be achieved at higher temperature.     

Beam Combination using Stimulated Brillouin Scattering for the Ultimate High Power-Energy Laser System Operating at High Repetition Rate over 10 Hz for Laser Fusion Driver

After the laser was invented in 1960, a phase conjugation mirror has been respected to be the most fantastic one for the laser resonator composition because it can compensate any distortions of the laser beams occurred by the many inhomogenuities of the laser media and optical components. Among the many phase conjugation configurations, the stimulated Brillouin scattering phase conjugation mirror is the most simple one and many researchers have tried to utilize it to develop high power/energy laser systems. For realizing a high energy/power laser system the thermal problem is the most difficult to solve, and some researchers suggested a beam combination technique to reduce the thermal load of the big laser media to many small sized ones. To accomplish the beam combination using stimulated Brillouin scattering phase conjugation mirrors (SBS-PCMs), it is necessary to lock/control the phases of the SBS-PCMs. And some researchers have developed several ways for it, but they can lock the phases of a limited number of beams overlapped at the foci less than 5, or lock the phases by back-seeding technique but it loses the phase conjugation characteristics. For realization of the laser fusion driver, it is necessary to combine more than 10 or 100 beams. And the authors have developed recently a new phase controlling/locking technique which is isolated and independent totally from other beams and it can be applied to an unlimited number of beams in principle.     

In‐line monitoring of UV photopolymerization with a quartz crystal resonator

An in‐line monitoring device using a quartz crystal resonator for thin film polymerization was proposed, and its performance has been evaluated by implementing in the UV polymerization of 2‐hydroxyethyl methacrylate with a photoinitiator of 1‐chloroanthraquinone. Because the variation of resonant resistance of the resonator is proportional to the square root of viscosity change that is closely related to the polymerization degree, the resistance can be used as a measure of the polymerization degree. The resistance measurements were compared with the outcome of instrumental analyses of polymerization degree using an FTIR spectrometer and a gel permeation chromatograph. The experimental results showed that the resistance measurements were consistent with the experimental outcome of the instrumental analyses, and this indicates the effectiveness of the proposed device. Owing to the simplicity and availability of the resonator system, its wide utilization in the monitoring of a variety of film polymerization processes, including photoresistor application, is expected. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2428–2439, 2006     

Synthesis and characterization of novel perfluorinated polyimides with 3D‐controlled structures for photonic applications

We have designed and synthesized novel perfluorinated polyimides with 3D controlled structure. At first, we successfully developed the new synthetic routes to diamines with pendant bulky perfluorinated aromatic units in a multi‐step synthetic procedure. Novel perfluorinated polyimides were prepared in a two‐step reaction in N‐methyl‐2‐pyrrolidinone (NMP) solution: The first step was for the synthesis of polyamic acids (PAAs) and the second reaction was for the imidization of PAA. The polymer yield was over 89% and the inherent viscosity of PAAs was in the range of 0.24–0.36 dL/g. The thin films were prepared by spin‐coating the PAA solution in NMP onto various substrates such as a Si wafer or a KBr pellet, dried at 80 °C and further cured at 230 °C. The resultant polyimides are thermally stable over 400 °C. The refractive index and birefringence of the resultant polyimides are 1.5858–1.6452 and 0.01–0.005, respectively. The refractive index of polyimide decreases with increasing the fluorine content. The copolymerization and the ether linkages into the backbone reduce the birefringence of polyimides. Surprisingly, the pendant ether linkage is not a crucial factor in reducing the polyimide birefringence. Their birefringence is comparatively very low, compared with that of previous polyimides. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1326–1342, 2006     

Synthesis and luminescence characteristics of conjugated dendrimers with 2,4,6‐triaryl‐1,3,5‐triazine periphery

We have synthesized conjugated dendrimer with triazine peripheries, and their luminescence properties were investigated. The dendrimers consist of dendritic triazine wedges for electron transport, distyrylbenzene core as an emitting moiety, and t‐butyl peripheral groups for good processing properties. The dendrimers have LUMO values of about ?2.7 eV possibly because of the triazine moiety with high electron affinity. Photoluminescence study indicates that energy transfer occurs from the triazine wedges to the stilbene bridge, and finally to the core chromophore units due to a cascade decrease of bandgap from the peripheral wedge to core moiety. Therefore, the emission wavelength was determined by the structure of the core unit. The energy transfer efficiency of distyrylbenzene‐cored dendrimers was about 75 and 55% for Trz‐1GD‐DSB and Trz‐2GD‐DSB, respectively. A preliminary electroluminescence property also was investigated. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 254–263, 2006     

Direct single-layered fabrication of 3D concavo–convex patterns in nano-stereolithography

A nano-surfacing process (NSP) is proposed to directly fabricate three-dimensional (3D) concavo–convex-shaped microstructures such as micro-lens arrays using two-photon polymerization (TPP), a promising technique for fabricating arbitrary 3D highly functional micro-devices. In TPP, commonly utilized methods for fabricating complex 3D microstructures to date are based on a layer-by-layer accumulating technique employing two-dimensional sliced data derived from 3D computer-aided design data. As such, this approach requires much time and effort for precise fabrication. In this work, a novel single-layer exposure method is proposed in order to improve the fabricating efficiency for 3D concavo–convex-shaped microstructures. In the NSP, 3D microstructures are divided into 13 sub-regions horizontally with consideration of the heights. Those sub-regions are then expressed as 13 characteristic colors, after which a multi-voxel matrix (MVM) is composed with the characteristic colors. Voxels with various heights and diameters are generated to construct 3D structures using a MVM scanning method. Some 3D concavo–convex-shaped microstructures were fabricated to estimate the usefulness of the NSP, and the results show that it readily enables the fabrication of single-layered 3D microstructures. PACS 85.40.Hp; 81.16.Nd; 42.82.Cr