Complex compounds of tetracycline with WO 4 2− and MoO 4 2− ions. Investigation by pH-metric and conductometric methods

By using pH-metric and conductometric methods it has been found that tetracycline (H₃TC) forms with WO ₄ ^2– and MoO ₄ ^2– ions the following complex compounds: [WO₃HTC]^2–, [WO₃(H₂TC)₂]^2– and [MoO₃(H₂TC)₂]^2–. Stability constants log/gb ₁ ^k =7.86 and log ₁ ^k =7.80 for [WO₃HTC]^2– and [MoO₃HTC]^2–, respectively, have been calculated from pH-metric measurements.     

Thermal stability of acrylonitrile/chlorosulphonated polyethylene rubber blend

The properties of chlorosulphonated polyethylene (CSM) rubber, acrylonitrile rubber (NBR) and their blend (50/50 w/w) were studied. Fourier transform infrared (FTIR) studies supported that CSM/NBR rubber blend is self curable, when cross-linking takes place between acrylonitrile groups of NBR and –SO₂Cl groups or in situ generated allyl chloride moieties of CSM. The thermal stability of vulcanizates was analyzed in nitrogen by thermogravimetry. It was found that the initial degradation temperature of elastomer based on CSM rubber is lower than of pure NBR rubber. By adding NBR to CSM rubbers, the degradation temperature of crosslinked material increased, indicating higher thermal stability. The activation energy for the degradation are determined using the Arrhenius equation The activation energies for the rubber blends are higher than for elastomers based on pure rubbers. It was found that the mass loss of the blends at any temperature was between those of the pure rubbers. The differential scanning calorimetry (DSC) was used for the glass transition temperature determination. It is estimated thermodynamic immiscibility of NBR/CSM blend based on noticed two different glass transition temperatures, corresponding to CSM and NBR rubbers.     

Particulate matter, gas-phase and particle-bound polycyclic aromatic hydrocarbons in an urban environment heavily impacted by vehicular traffic (Bologna, Italy)

A set of 8 polycyclic aromatic hydrocarbons (PAHs) has been analysed in a traffic-limited area in Bologna downtown, both in the gas-phase and in the particulate phase (PM10), and gas-to-particle partitioning has been investigated. From Sep 2002 to May 2003, 28 high volume PM10 samplings were carried out, and in 50 % of the samplings, PM10 concentrations exceeded the limit of 50 microg/m3 established by a 1999 EU directive. A precisely defined sampling strategy was adopted to limit artifacts (8 h sampling in the same time interval) in the 28 samplings carried out in different meteorological conditions. A linear log-log correlation was found between gas-particle partitioning coefficients KBp and the subcooled liquid vapour pressures pB0LB, with rP2P = 0.82 and slope = -0.59. This empirical correlation may be used to anticipate the total (gas + particle-bound) concentration of each PAHs in this urban site, once PM10 and the particle-bound concentration is measured. Parallel samplings of PM10 and of PM2.5 allowed us to ascertain that PM2.5 represents the gross contribution to PM10 and that most of the particle-bound PAHs reside on the finest fraction of particulate matter.     

N,N,N-trimethylchitosan iodide complexes with a weak or a strong polyacid and nanoparticles thereof

Polyelectrolyte complexes (PECs) were prepared from N,N,N-trimethylchitosan iodide (TMCh) of different molar mass and a weak polyacid-poly(acrylic acid) (PAA) or a strong polyacid-poly(2-acrylamido-2-methylpropanesulfonic acid) (PAMPS). The quaternization of the amino groups of chitosan enabled the formation of water-insoluble PECs in a broad pH range—from 3 to 12 and from 1 to 12 for TMCh/PAA and TMCh/PAMPS, respectively. Whereas the stoichiometry of the TMCh/PAA complex was pH dependant, the stoichiometry of the TMCh/PAMPS complex did not depend on pH. The stoichiometry and the yield of the complexes were influenced by the molar mass of TMCh. PEC nanoparticles were produced by mixing dilute solutions of the oppositely charged polyelectrolytes as revealed by dynamic light scattering analyses. The size of the particles was in the range of 135–924 nm and depended on the polyelectrolyte molar mass, the initial polyelectrolyte concentration, and the molar fraction of the TMCh units. Microbiological screening against Staphylococcus aureus and Escherichia coli revealed that PECs between TMCh and PAA or PAMPS have a good antibacterial effect, which is more slowly pronounced than that of the starting TMCh of different molar mass.     

The sorption of anthracene onto goethite and kaolinite in the presence of some benzene carboxylic acids

The uptake of anthracene from dilute aqueous solutions onto goethite and kaolinite was investigated at 25 degrees C, first in the absence and then in the presence of three benzene carboxylic acids: phthalic acid (benzene-1,2-dicarboxylic acid), trimesic acid (-1,3,5-), and mellitic acid (-1,2,3,4,5,6-). Carboxylic acid concentrations were 0.20, 0.10, and 0.05 mM. Anthracene (0.20 microM) did not adsorb strongly onto the pure mineral surfaces, but in the presence of phthalic acid a substantial increase in anthracene uptake was observed, particularly for the goethite systems. Trimesic and mellitic acids did not enhance anthracene uptake. Phthalate and proton adsorption data have been used to model phthalate adsorption onto the mineral surfaces using an extended constant capacitance surface complexation model. This model was then successfully adapted to account for the observed increase in anthracene uptake, where anthracene molecules were assumed to interact with adsorbed phthalate. We propose that the enhancement of anthracene adsorption in the presence of phthalic acid is due to an increase in the hydrophobicity of the mineral surface once phthalic acid molecules adsorb. The same effect was not observed for the other benzene carboxylates because of their greater polarity.     

Visible and near-infrared absorption spectroscopy by an integrating sphere and optical fibers for quantifying and discriminating the adulteration of extra virgin olive oil from Tuscany

Because of its high price, extra virgin olive oil is frequently targeted for adulteration with lower quality oils. This paper presents an innovative optical technique capable of quantifying and discriminating the adulteration of extra virgin olive oil caused by lower-grade olive oils. An original set-up for diffuse-light absorption spectroscopy in the wide 400–1,700 nm spectral range was experimented. It made use of an integrating sphere containing the oil sample and of optical fibers for illumination and detection; it provided intrinsically scattering-free absorption spectroscopy measurements. This set-up was used to collect spectroscopic fingerprints of authentic extra virgin olive oils from the Italian Tuscany region, adulterated by different concentrations of olive-pomace oil, refined olive oil, deodorized olive oil, and refined olive-pomace oil. Then, a straightforward multivariate processing of spectroscopic data based on principal component analysis and linear discriminant analysis was applied which was successfully capable of predicting the fraction of adulterant in the mixture, and of discriminating its type. The results achieved by means of optical spectroscopy were compared with the analysis of fatty acids, which was carried out by standard gas chromatography.     

CdS-containing nano-assemblies of double hydrophilic block copolymers in water

Two samples of poly(sodium(sulfamate-carboxylate)isoprene)-block-poly(ethylene oxide) copolymer (SCIEO-1 and SCIEO-2) differing in molecular weight and relative length of polyelectrolyte blocks have been used as templates for the synthesis of cadmium sulfide (CdS) nanoparticles in aqueous media. The double-hydrophilic copolymer SCIEO has very high 1D charge density, and its polymer chain structure mimics that of polysaccharide heparin. It is soluble in aqueous media, but the addition of cadmium acetate (Cd(Ac)₂) to its aqueous solution causes the formation of micellar aggregates with Cd²⁺containing insoluble cores above the threshold Cd²⁺ concentration. The trapped Cd²⁺ ions can be chemically transformed to CdS nanoparticles. The stability of hybrid SCIEO/CdS micelles depends on the ratio of PEO-to-SCI lengths: it was found that the SCIEO-2 copolymer with sufficiently long PEO block behaves as an effective stabilizer for the synthesis of CdS nanoparticles embedded in micelles, while SCIEO-1 does not. The morphology of aggregates varies with the Cd-to-SCI ratios and ranges from spherical to mixture of spherical and necklace-like micellar aggregates. A number of experimental techniques including static and dynamic light scattering, fluorescence correlation spectroscopy, atomic force and transmission electron microscopy, UV-vis, and fluorescence spectroscopy were employed for the characterization of both CdS containing hybrid micelles and embedded CdS nanoparticles.     

Extraction of phytosterols from tall oil soap using selected organic solvents

Tall oil soap as a waste product of the sulphate cellulose production process was treated by single-stage liquid-liquid extraction. The aim of this study was to compare yields of health beneficial matters contained in tall oil soap when several extraction solvents, recommended in literature, were used. Hexane, 1-methyl-4-(1-methylethenyl)-cyclohexene, 2-methylpropan-1-ol, hexan-1-ol, 4-methylpentan-2-one, 2-methoxy-2-methylpropane, and butyl ethanoate were tested. For hydrocarbons it was necessary to add a de-emulsifier into the system, which limits the formation of foams and stable emulsions. The highest yields of total phytosterols (78 %) and especially of β-sitosterol (100 %) were reached when butyl ethanoate was used. However, it was necessary to adjust pH of the treated raw material to approximately 7. The highest yields for feed where pH was not adjusted were obtained with 2-methylpropan-1-ol: 67 % of total sterols and 89 % of β-sitosterol. Disadvantages of most of the tested solvents included the formation of the undesirable solid interphase which could not be removed, partial solubility of the solvents in the water phase, their high boiling point and/or instability. These disadvantages prevent the use of these solvents in industrial applications; they also complicate the treatment of tall oil soap by liquid-liquid extraction or the regeneration of the used organic solvent.     

Study of charge storage in the nanofibrous poly(ethylene terephthalate) electrets prepared by electrospinning or by corona discharge method

In this paper, the charge storage performance of electrospun poly(ethylene terephthalate) (PET) mats with high specific surface area was evaluated in comparison to that of PET film electrets. Corona discharge method was used to charge the electrospun PET mats and PET films. The surface potential decay measurements revealed that the corona charged РЕТ mats had higher initial values for the normalized surface potential compared to the РЕТ electret films. A tendency for stabilization of the electret charge to one and the same value for all charged samples (mats and films) after the 50th day was observed. The peaks at 90 °C in the thermally stimulated current (TSC) spectra of uncharged and charged in corona discharge electrospun PET mats were observed and attributed to a relaxation of the separated space charges, the dipole disorientation or injected charges within the bulk. It was found that the value of the storage charge in a corona charged electrospun PET mats was higher than that in PET mats prepared by electrospinning.