Influence of the composition of the polymer matrix on the electrooptical properties of films with a dispersed liquid crystal

Polymer films with a dispersed liquid crystal were prepared by photopolymerization of (meth)acrylic monomers. The electrooptical properties of these films were studied. The influence exerted by the composition of the monomer mixture, cross-linking agents, and chain-transfer agent on the liquid crystal drop size and on the transmission of the polymer-liquid crystal films was examined.     

Study of the dynamic structure factor of strong glasses

The dynamic structure factors (DSFs) of several strong glasses (SF6, SF10, BK7, SUPRASIL) measured by Brillouin light scattering spectroscopy are reported. Spectra have been collected, at and above room temperature, at two scattering angles, θ=90° and θ=180° corresponding to exchanged wavevector q values ranging from 0.0256 to 0.0448 nm⁻¹. In particular we find that the isotropic spectral lineshapes are in all cases well described by the simple hydrodynamic theory of an amorphous solid. The width of the Brillouin peaks are found to be consistent with the predicted q² dependence at both investigated temperatures. This damping is however found to account only partially for the strong asymmetry of the Brillouin line clearly visible on a logarithmic intensity scale. As a matter of fact there is an excess intensity in the very low frequency plateau underlying the central component. The height of this plateau and hence the entire lineshape is well reproduced if a relaxation process is taken into account in the hydrodynamic equations. Owing to the intense elastic scattering we are able to determine unambiguously only the ratio between amplitude and characteristic time of this process which quantifies the sound dispersion to be of the order of a few percent in all samples. The temperature dependence of the parameters indicates that this relaxation cannot be attributed to thermally activated relaxation phenomena. These general findings favorably compare with molecular dynamics simulation results on similar systems.     

Closed-form solutions for a rectangular layer with central crack under anti-plane shear stress

We consider the problem of determining the stress distributionin a finite rectangular elastic layer containing a Griffithcrack which is opened by internal shear stress acting alongthe length of the crack. The mode III crack is assumed to belocated in the middle plane of the rectangular layer. The followingtwo problems are considered: (A) the central crack is perpendicularto the two fixed lateral surfaces and parallel to the othertwo stress-free surfaces; (B) all the lateral surfaces of therectangular layer are clamped and the central crack is parallelto the two lateral surfaces. By using Fourier transformations,we reduce the solution of each problem to the solution of dualintegral equations with sine kernels and a weight function whichare solved exactly. Finally, we derive closed-form expressionsfor the stress intensity factor at the tip of the crack andthe numerical values for the stress intensity factor at theedges of the cracks are presented in the form of tables.     

A transform method for linear evolution PDEs on a finite interval

We study initial boundary value problems for linear scalar evolutionpartial differential equations, with spatial derivatives ofarbitrary order, posed on the domain {t > 0, 0 < x <L}. We show that the solution can be expressed as an integralin the complex k-plane. This integral is defined in terms ofan x-transform of the initial condition and a t-transform ofthe boundary conditions. The derivation of this integral representationrelies on the analysis of the global relation, which is an algebraicrelation defined in the complex k-plane coupling all boundaryvalues of the solution. For particular cases, such as the case of periodic boundaryconditions, or the case of boundary value problems for even-orderPDEs, it is possible to obtain directly from the global relationan alternative representation for the solution, in the formof an infinite series. We stress, however, that there existinitial boundary value problems for which the only representationis an integral which cannot be written as an infinite series.An example of such a problem is provided by the linearized versionof the KdV equation. Similarly, in general the solution of odd-orderlinear initial boundary value problems on a finite intervalcannot be expressed in terms of an infinite series.     

Methods for implementing the stream boundary condition in DSMC computations

In the direct simulation Monte‐Carlo (DSMC) method for simulating rarefied gas flows, the velocities of simulator particles that cross a simulation boundary and enter the simulation space are typically generated using the acceptance–rejection procedure that samples the velocities from a truncated theoretical velocity distribution that excludes low and high velocities. This paper analyses an alternative technique, where the velocities of entering particles are obtained by extending the simulation procedures to a region adjacent to the simulation space, and considering the movement of particles generated within that region during the simulation time step. The alternative method may be considered as a form of acceptance–rejection procedure, and permits the generation of all possible velocities, although the population of high velocities is depleted with respect to the theoretical distribution. Nevertheless, this is an improvement over the standard acceptance–rejection method. Previous implementations of the alternative method gave a number flux lower than the theoretical number required. Two methods for obtaining the correct number flux are presented. For upstream boundaries in high‐speed flows, the alternative method is more computationally efficient than the acceptance–rejection method. However, for downstream boundaries, the alternative method is extremely inefficient. The alternative method, with the correct theoretical number flux, should therefore be used in DSMC computations in favour of the acceptance–rejection method for upstream boundaries in high‐speed flows. Copyright © 2003 John Wiley & Sons, Ltd.     

A numerical and experimental investigation of the interactions between a non‐uniform planar array of incompressible free jets

The interaction between multiple incompressible air jets has been studied numerically and experimentally. The numerical predictions have been first validated using experimental data for a single jet configuration. The spreading features of five unequal jets in the configuration of one larger central jet surrounded by four smaller equi‐distant jets, have been studied, for different lateral spacing ratios of 1.5, 2.0 and 2.5 and a central jet Reynolds number of 1.24×105 (corresponding to a Mach number of 0.16). Flow of five equal jets has also been simulated, for the sake of comparison. The jet interactions commence at an axial distance of about 3–4 diameters and complete by an axial distance of about 10 diameters for the lowest spacing ratio of 1.5. For larger spacing ratios, the length required for the start and completion of jet interaction increase. Peripheral jets bend more towards the central jet and merge at a smaller distance, when their sizes are smaller than that of the central jet. The entrainment ratio for multiple jets is higher than that for a single jet. Excellent agreement is observed between the experimental data and theoretical predictions for both mean flow field and turbulent quantities, at regions away from the jet inlet. The potential core length and initial jet development, however, are not predicted very accurately due to differences in the assumed and actual velocity profiles at the jet inlet. Copyright © 2004 John Wiley & Sons, Ltd.     

Robust handling of non‐linear constraints for GA optimization of aerodynamic shapes

A new approach to the robust handling of non‐linear constraints for GAs (genetic algorithms) optimization is proposed. A specific feature of the approach consists of the change in the conventional search strategy by employing search paths which pass through both feasible and infeasible points (contrary to the traditional approach where only feasible points may be included in a path). The method (driven by full Navier–Stokes computations) was applied to the problem of multiobjective optimization of aerodynamic shapes subject to various geometrical and aerodynamic constraints. The results demonstrated that the method retains high robustness of conventional GAs while keeping CFD computational volume to an acceptable level, which allowed the algorithm to be used in a demanding engineering environment. Copyright © 2004 John Wiley & Sons, Ltd.