Dark pulse generation in a dispersion-managed fiber laser

We report an experimental observation of dark pulse generation in a dispersion-managed erbium-doped fiber laser with net anomalous cavity group-velocity dispersion. It is found that apart from the bright soliton pulses, dark pulses with spectral sidebands could be obtained in the laser under appropriate operating conditions. The generation of dark pulses may be attributed to soliton shaping in the cavity.     

Completeness in Supergravity Constructions

We prove that the supergravity r- and c-maps preserve completeness. As a consequence, any component \({\mathcal{H}}\) of a hypersurface {h = 1} defined by a homogeneous cubic polynomial h such that \({-\partial^2h}\) is a complete Riemannian metric on \({\mathcal{H}}\) defines a complete projective special Kähler manifold and any complete projective special Kähler manifold defines a complete quaternionic Kähler manifold of negative scalar curvature. We classify all complete quaternionic Kähler manifolds of dimension less or equal to 12 which are obtained in this way and describe some complete examples in 16 dimensions.     

Diode pumped active-mirror Yb:YAG ceramic lasers

Lasers from Yb:YAG ceramic at different temperature were reported in this paper. The Yb:YAG ceramic laser with active-mirror structure was end-pumped by a laser diode whose central wavelength was 940 nm. At 80 K, with doping concentration of 5 at % Yb:YAG ceramic slab, output energy of 0.68 J at 10 Hz repetition rate was obtained under the pump energy of 2.49 J, corresponding to a slope efficiency of 40% and a conversion efficiency of 27.3%, respectively.     

Resonantly pumped continuous wave Er:YAP laser

A continuous wave Er:YAP laser pumped by Mgo:PPLN laser locked at 1535 nm was reported. 170 mW of 1609 nm output was achieved under total incident pump power of 7 W at 77 K. The slope efficiency were 5.0 and 3.1% with the cavity length 75 and 140 mm.     

Residual microstructure associated with impact craters in TiB2/2024Al composite

Residual microstructures associated with hypervelocity impact craters in 55 vol.% TiB(2)/2024Al composite were investigated by transmission electron microscopy (TEM) and high-resolution transmission electron microscopy (HRTEM). TiB(2)-Al interface, TiB(2) particles and Al matrix before and after hypervelocity impact were compared to discuss the effect of hypervelocity impact. A new Al(x)O(1-x) phase with the fcc structure and the crystal parameter of 0.69 nm was formed at TiB(2)-Al interface. Stacking fault with width of 10-20 nm was formed along the (001) plane of TiB(2) particle. Formation of nanograins (≈ 100 nm) was observed within Al matrix, moreover, lamellar S' phase was transformed into lenticular or spherical S phase after hypervelocity impact.     

Evidence for spin correlation in t ̅t production

We present a measurement of the ratio of events with correlated t and t ?t spins to the total number of t ?t events. This ratio f is evaluated using a matrix-element-based approach in 729 t ?t candidate events with a single lepton ? (electron or muon) and at least four jets. The analyzed p ?p collisions data correspond to an integrated luminosity of 5.3 fb(-1) and were collected with the D0 detector at the Fermilab Tevatron collider operating at a center-of-mass energy √s=1.96 TeV. Combining this result with a recent measurement of f in dileptonic final states, we find f in agreement with the standard model. In addition, the combination provides evidence for the presence of spin correlation in t ?t events with a significance of more than 3 standard deviations.     

Interaction between graphene and the surface of SiO2

The interaction between graphene and a SiO(2) surface has been analyzed with first-principles DFT calculations by constructing the different configurations based on α-quartz and cristobalite structures. The fact that single-layer graphene can stay stably on a SiO(2) surface is explained based on a general consideration of the configuration structures of the SiO(2) surface. It is found that the oxygen defect in a SiO(2) surface can shift the Fermi level of graphene down which opens up the mechanism of the hole-doping effect of graphene adsorbed on a SiO(2) surface observed in a lot of experiments.     

Effects of oxygen-containing defect complex on the electronic structures and transport properties of single-walled carbon nanotubes

The electronic structures and transport properties of (10,0)$(10,0)$ single-walled carbon nanotube ((10,0)$(10,0)$ (SWNT)) with oxygen-containing defect complex are investigated using density functional theory in combination with nonequilibrium Green?s function method. The complex delocalizes the local states of (10,0)$(10,0)$ SWNT induced by mono- and di-vacancy but strengthens the localization of the states induced by the Stone–Wales defect. As a result, the complex partially restores the transport properties of (10,0)$(10,0)$ SWNT with vacancies, but reduces the transmission of (10,0)$(10,0)$ SWNT with Stone–Wales defect. However, the oxygen-containing defect complex only slightly influences the transmission gap and threshold voltage of the system.     

Uncertainty-based experimental validation of nonlinear reduced order models

This paper presents the first results of a combined experimental–computational investigation focused on the validation of reduced order models of geometrically nonlinear structures in the presence of uncertainty. The validation approach considered here is based on the premise that the model is valid if the experimental results can be considered as random sample responses of the stochastic system of which the reduced order model is the mean. For the situation considered here, the power spectra of the experiments should lie within the 2nd and 98th percentiles of the response (forming the uncertainty band) of the stochastic model. Nominally clamped–clamped beams are considered to demonstrate the entire process. The construction of two mean reduced order models and their stochastic counterparts are first performed. Then, the validation effort is carried out by comparing experimentally obtained power spectra and their corresponding computational uncertainty bands. This process leads, for both reduced order models, to a very good representation of the important upper envelope (98th percentile) of the experimental data but a less good fit of the lower envelope (2nd percentile).