Electrical and optical characteristics of porous silicon impregnated with LaF3 by a novel chemical bath technique

The structural, electrical and optical characteristics of porous silicon (PS) due to the impregnation of LaF₃ into PS by a novel chemical-bath deposition (CBD) technique have been investigated in this article. Without removing the PS from the anodization chamber the impregnation with LaF₃ has been done by reacting LaCl₃ with HF in the same chamber at room temperature. The impregnation of LaF₃ was confirmed by the SEM on the cross-section of the LaF₃/PS/Si system and EDX. The modification of PS surface by LaF₃ had direct influence on the electrical and optical properties of PS. Electrical properties of Ag/LaF₃/PS/p-Si/Ag structures were studied through the current-voltage (I-V) and capacitance-voltage (C-V) characteristics. Formation of metal-insulator-semiconductor (MIS) diode was evident whose forward current increased with annealing. A diode factor of about 2.4 has been obtained for the annealed heterostructure indicating a high density of trap states. The C⁻²-V curves of all samples showed negative flat band voltage of around −2 V confirming a large number of fixed positive charges in the LaF₃. The photoluminescence (PL) intensity of the LaF₃-impregnated PS showed aging for the as-deposited samples, but when annealed PS structure recovered the PL intensity. Experimental results show that the optimized chemical bath passivation process for the LaF₃ on porous silicon could enable the porous silicon to be an important material for photonic application.     

Effect of transmission fiber and amplifier noise on optical chaos synchronization

Optical chaos propagation has few constraints peculiar to itself which do not become as significant in conventional nonchaotic optical communication. We have investigated the effects of transmission fiber nonlinearities, dispersion and noise of erbium doped fiber amplifier (EDFA) on chaotic signal synchronization in lumped and distributed configuration. It is found that the effects of fiber dispersion can be easily compensated; however, the effects of fiber nonlinearity on chaos cannot be overdone and must be avoided. Three distinct configurations with different combinations of standard telecommunication fiber, dispersion compensation fiber and lumped and distributed EDF for amplification are analysed. The results are compared in terms of sync diagrams and noise figure. The chaos after propagation through distributed amplification performs better as compared to lumped amplification. Also, a new quantitative measure for the calculation of deviation in sync diagram of chaos is introduced.     

The radiation shielding offered by the commercial glass installed in Bangladeshi dwellings

One sign of a vibrant Bangladeshi economy has been the move away from the use of more traditional housing materials towards a preference for modern constructional media. Glass, one such example, used both decoratively and in a structural context, offers various advantageous properties and facets including a protective feature against radiation that has not previously been considered. Current interest examines the dosimetric possibilities offered by the commercial glass as a secondary shield and also in retrospective ionising radiation exposure analysis. Four popular brands of window glass are investigated, all available within the local market (PHP-Bangladesh, Usmania-Bangladesh, Nasir-Bangladesh and Rider-China), all with the same thickness and colour, varying in terms of elemental weight fractions as evaluated by energy dispersive X-ray analysis. As potential attenuators of transmitted radiation thereby forming secondary barriers against radiation exposure from penetrating radiations, the four brands of glass have been studied using photon energies from 59 up to 1332 keV, a range of values representative of that potentially encountered in incidents. Use has been made of a well-shielded high-purity germanium γ-ray spectrometer and associated electronics, providing for evaluation of the characteristic barrier parameters of half-value layer, radiation protection efficiency and effective atomic number (Z_eff). Of the four brands investigated, Rider provides superior secondary shielding performance. Concerning potential retrospective dosimetry the effective atomic number of the glass samples are comparable with that of the commercial thermoluminescence (TL) dosimeter TLD-200. At high doses, the TL yields are sufficient to provide for retrospective accident dosimetry.     

Effect of Ni content on the diffusion-controlled growth of the product phases in the Cu(Ni)–Sn system

A strong influence of Ni content on the diffusion-controlled growth of the (Cu,Ni)₃Sn and (Cu,Ni)₆Sn₅ phases by coupling different Cu(Ni) alloys with Sn in the solid state is reported. The continuous increase in the thickness ratio of (Cu,Ni)₆Sn₅ to (Cu,Ni)₃Sn with the Ni content is explained by combined kinetic and thermodynamic arguments as follows: (i) The integrated interdiffusion coefficient does not change for the (Cu,Ni)₃Sn phase up to 2.5 at.% Ni and decreases drastically for 5 at.% Ni. On the other hand, there is a continuous increase in the integrated interdiffusion coefficient for (Cu,Ni)₆Sn₅ as a function of increasing Ni content. (ii) With the increase in Ni content, driving forces for the diffusion of components increase for both components in both phases but at different rates. However, the magnitude of these changes alone is not large enough to explain the high difference in the observed growth rate of the product phases because of Ni addition. (iv) Kirkendall marker experiments indicate that the Cu₆Sn₅ phase grows by diffusion of both Cu and Sn in the binary case. However, when Ni is added, the growth is by diffusion of Sn only. (v) Also, the observed grain refinement in the Cu₆Sn₅ phase with the addition of Ni suggests that the grain boundary diffusion of Sn may have an important role in the observed changes in the growth rate.     

Organic/inorganic interfaced field-effect transistor properties with a novel organic semiconducting material

A novel 1,3,4-oxadiazole-substituted benzo[b]triphenylene was synthesized by three-step synthetic procedure and OFET device design was successfully designed after theoretical calculations made using Gaussian software. For investigating the field-effect properties of designed organic electronic device, a SiO₂ (300 nm) was thermally grown on p-Si wafer at 1000 °C as a dielectric layer and gate, source and drain contacts have been deposited using Au metal with physical vapour deposition. 1,3,4-Oxadiazole-substituted benzo[b]triphenylene was spin coated on the source and drain electrodes of our device, forming organic/inorganic interfaced field-effect transistors. Surface morphology and thin film properties were investigated using AFM. All electrical measurements were done in air ambient. The device showed a typical p-type channel behaviour with increasing negative gate bias voltage values. Our results have surprisingly shown that the saturation regime of this device has high mobility (μ_FET), excellent on/off ratio (I_on/I_off), high transconductance (g_m) and a small threshold voltage (V_Th). The values of μ_FET, I_on/I_off, g_m and V_Th were found as 5.02 cm²/Vs, 0.7 × 10³, 5.64 μS/mm and 1.37 V, respectively. These values show that our novel organic material could be a potential candidate for organic electronic device applications in the future.     

An improved model for computing the reflectivity of a AlAs/GaAs based distributed bragg reflector and vertical cavity surface emitting laser

In this paper, reflectivity of a Distributed Bragg Reflector (DBR) has been computed by considering the effects of changes of wavelength on the changes of the refractive index of the materials of DBR layers. The intrinsic losses of the materials have been included in the computation of the reflectivity of the DBR. It has been found that the effect of change of the wavelength on the refractive index of the DBR materials reduces the Full Width Half Maxima (FWHM) of the stop band significantly which is expected to improve the laser characteristics. If the FWHM is reduced, the thickness of the active layer of a VCSEL can also be reduced which will further reduce the threshold current of the device. It has been found that the intrinsic losses of the materials have a significant effect on the reflectivity of a DBR. It has also been found that peak reflectivity of a 20 pair AlAs/GaAs DBR reduces by 0.2% after including the intrinsic losses (with a value of the intrinsic losses α = 10 cm^?1).     

Study of reduction processes over cerium oxide surfaces with atomic hydrogen using ultra accelerated quantum chemical molecular dynamics

Ceria plays an important role in catalysis, due to its ability to store and release oxygen depending on the condition present in the catalyst environment. To analyze the role of ceria in catalytic reactions, it is necessary to know the details of the interaction of ceria surface with environmentally sensitive molecules. This study was conducted using ultra accelerated quantum chemical molecular dynamics. Its purpose was to investigate the reduction process of the (1 1 1) and (1 1 0) surfaces of ceria with atomic hydrogen as well as water desorption mechanisms from the surfaces. This simulation demonstrated that when a high-energy colliding hydrogen atoms are adsorbed on the ceria, it pulls up an O atom from the ceria surfaces and results in the formation of a H₂O molecule. This is the first dynamics simulation related to such reduction processes based on quantum chemistry.     

A Review on Effects of Lubricant Formulations on Tribological Performance and Boundary Lubrication Mechanisms of Non-Doped DLC/DLC Contacts

Tribological efficiency of industrial applications involving boundary lubrication regime can be improved to an appreciable extent by the deposition of hard coatings on interacting surfaces. Among such coatings, diamond-like carbon (DLC) coatings are considered to be one of the most suitable ones for the said role. DLC coatings possess a unique combination of physical, chemical, and material properties due to which they can help in minimizing friction-induced energy and material losses even under starved lubrication conditions. Since commercial lubricants are optimized for steel surfaces, therefore, a lot of experimental investigations were carried out to analyze the tribological compatibility of these lubricants with various DLC coatings. However, there is still a lack of understanding about how DLC coatings interact with conventional lubricant additives. Some researchers reported tribologically beneficial interactions between DLC coatings and formulated lubricants while others observed no such behavior. To address these inconsistencies, there is a need to rearrange the published data in a more apprehensible and organized manner with a special emphasis on the mechanisms responsible for a particular tribological behavior. In this way, it can be determined whether synergistic or antagonistic correlation exists between a particular DLC-lubricant combination and research on DLC coatings can be continued in a logical way. In this article, most widely investigated non-doped DLC coatings (ta-C, a-C:H, a-C, and ta-C:H) are tribologically analyzed. Average values of friction and wear coefficients are calculated for various DLC-lubricant combinations using already published data and compared to quantify the effectiveness of a particular lubricant additive in enhancing tribological characteristics of symmetrical non-doped DLC contacts. Moreover, tribological performance parameters of non-doped DLC coatings are compared with those of doped-DLC coatings to understand differences in their tribological behavior in combination with additives.     

A Novel Implementation Technique of Conical Scan Radar Using A Programmable Phased Array

In radar, planar phased array antenna plays vital role in electronic scanning in the azimuth and elevation direction to the horizon. In most operations using planar phased array both the coordinates of azimuth and elevation, are steered electronically. In this paper a conceptual schematic of a phased array antenna with programmable time delay units has been presented. It is shown that by suitably exploiting the time delay matrix one can have electronic beam rotation around the target axis as required in conical scan. Thus both the elevation and azimuth motors in conical scan system are replaced by electronic scanning. Heuristically, we have selected eight consecutive points for beam rotation in a polygon shape and can also be extended almost circular shape by increasing number of array elements and phase shifter (delays) in the delay matrix. The array requires dual control of phase gradient and individual phase values. The whole array is controlled by micro-controller. This presents exciting possibilities in radar operation.