Synthesis of highly sulfonated poly(arylene ether sulfone) random (statistical) copolymers via direct polymerization

Novel biphenol‐based wholly aromatic poly (arylene ether sulfones) containing pendant sulfonate groups were prepared by direct aromatic nucleophilic substitution polycondensation of disodium 3,3′‐disulfonate‐4,4′‐dichlorodiphenyl sulfone (SDCDPS), 4,4′‐dichlorodiphenylsulfone (DCDPS) and biphenol. Copolymerization proceeded quantitatively to high molecular weight in N‐methyl‐2‐pyrrolidinone at 190°C in the presence of anhydrous potassium carbonate. Tough membranes were successfully cast from the control and the copolymers, which had a SDCDPS/DCDPS mole ratio of either 40:60 or 60:40 using N,N‐dimethylactamide; the 100% SDCDPS homopolymer was water soluble. Short‐term aging (30 min) indicates that the desired acid form membranes are stable to 220°C in air and conductivity values at 25°C of 0.110 (40%) and 0.170 S/cm (60%) were measured, which are comparable to or higher than the state‐of‐the art fluorinated copolymer Nafion 1135 control. The new copolymers, which contain ion conductivity sites on deactivated rings, are candidates as new polymeric electrolyte materials for proton exchange membrane (PEM) fuel cells. Further research comparing their membrane behavior to post‐sulfonated systems is in progress.     

High-performance liquid chromatographic assay for mitoxantrone in plasma using electrochemical detection

A sensitive and specific high-performance liquid chromatographic (HPLC) assay was developed for the quantitation of mitoxantrone in plasma using electrochemical detection. Bisantrene was chosen as the internal standard. A reversed-phase, 10-microns muBondapak C18 analytical column (30 cm X 3.9 mm) with an isocratic mobile phase of 28% acetonitrile in 80 mM sodium formate buffer (pH 3.0) was used. The eluent was monitored by both electrochemical detection at an applied potential of +0.75 V vs. Ag/AgCl and visible absorbance at 660 nm. Only electrochemical detection was able to quantitate the internal standard and provided ten times higher sensitivity than visible absorbance for mitoxantrone with a detection limit as low as 0.1 ng/ml. Calibration curves in the range 0.1-1000 ng/ml showed good linearity (r = 0.998) and precision (coefficient of variation less than 10%). This HPLC method utilized a reproducible and inexpensive liquid-liquid extraction procedure. Using methylene chloride, the extraction efficacy of mitoxantrone from plasma was 85.3% with a coefficient of variation less than 2.1%. This new assay was then applied to measure mitoxantrone concentrations in plasma obtained from two leukemic patients receiving 12 mg/m2 mitoxantrone as a 1-h infusion.     

Synthesis, structure, and dynamics of nickelacarboranes incorporating the [nido-7,9-C(2)B(9)H(11)](2)(-) ligand

The nickelacarboranes [NEt(4)][2-(eta(3)-C(3)H(4)R)-closo-2,1,7-NiC(2)B(9)H(11)] (R = H (1a), Ph (1b)) have been synthesized via reaction between [Na](2)[nido-7,9-C(2)B(9)H(11)] and [Ni(2)(micro-Br)(2)(eta(3)-C(3)H(4)R)(2)] in THF (THF = tetrahydrofuran), followed by addition of [NEt(4)]Cl. Protonation of 1a in the presence of a donor ligand L affords the complexes [2,2-L(2)-closo-2,1,7-NiC(2)B(9)H(11)] (L = CO (2), CNBu(t) (3)). Addition of PEt(3) (1 equiv) to 2 produces quantitative conversion to [2-CO-2-PEt(3)-closo-2,1,7-NiC(2)B(9)H(11)], 4. Species 2-4 exhibit in solution hindered rotation of the NiL(2) fragment with respect to the eta(5)-C(2)B(9) cage unit. Protonation of 1a in the presence of a diene affords the neutral complexes [2-(eta(2):eta(2)-diene)-closo-2,1,7-NiC(2)B(9)H(11)] (diene = C(5)Me(5)H (5), dcp (6), cod (7), nbd (8), chd (9), and cot (10a); dcp = dicyclopentadiene, cod = 1,5-cyclooctadiene, nbd = norbornadiene, chd = 1,3-cyclohexadiene, and cot = cyclooctatetraene). Variable temperature (1)H NMR experiments show that the [Ni(diene)] fragments are freely rotating even at 193 K. A small quantity of the di-cage species [2,2'-micro-(1,2:5,6-eta-3,4:7,8-eta-cot)-(closo-2,1,7-NiC(2)B(9)H(11))(2)] (10b) is formed as a coproduct in the synthesis of 10a. This species can be rationally synthesized by protonation of 1a and subsequent addition of 10a.     

Synthesis and Characterization of Triphenylphosphine Oxide-Containing Poly(Aryl Imide)-Poly(Dimethyl Siloxane) Randomly Segmented Copolymers

Abstract

Poly(aryl imide)-poly(dimethyl siloxane) randomly segmented copolymers were synthesized by essentially a one-step solution imidization process in a solvent system consisting of predominately o-dichlorobenzene with a small amount of n-methylpyrolidone. This solvent combination was selected because of its ability to afford homogeneous solutions throughout the polymerization process. This enabled copolymers of any desired poly(dimethyl siloxane) composition to be prepared. A hydrolytically stable triphenylphosphine oxide containing diamine, bis(3-amino-phenoxy-4′-phenyl)phenylphosphine oxide, was utilized as a chain extender and together with oxydiphthalic anhydride formed the hard segment in these copolymers. The soft segment was formed from α,ω-aminopropyl poly(dimethyl siloxane) oligomers of controlled molecular weight. The presence of phosphorus and silicon contributes several unique properties to the system, including enhanced solubility, thermal stability, and flame resistance. High molecular weight copolymers containing up to 60% (w/w) of the poly(dimethyl siloxane) segments were successfully prepared using this method. Gel permeation chromatography analysis, based on a universal calibration curve in CHCl₃, was performed to determine the molecular weights and distribution. These copolymers with 40-60% (w/w) poly(dimethyl siloxane) exhibited upper T_g values ranging from 130 to 180°C and showed substantial char yields at 750°C in air, which increased with siloxane content. Dynamic mechanical analysis confirmed the anticipated microphase behavior by the presence of two separate glass-transition regions. Both small angle x-ray scattering and transmission electron microscopy measurements determined on well-characterized transparent cast films were used to better demonstrate the multiphase nature of these copolymers.     

Synthesis and characterization of 3-phenylethynyl endcapped matrix resins

The synthesis of 3-phenylethynylphenol, and its applicability as a high temperature cross-linking endcap for high T_g polyarylene ethers is described. It was synthesized in high yields and purity using the palladium catalyzed coupling reaction between the protected 3-bromo or iodo phenol and phenylacetylene. The yield of the reaction was found to be highly dependent on the structure of the halide used, the reaction temperature, and the concentration of phenylacetylene. The use of the protected phenol in the palladium catalyzed reaction was also extended to the high yield synthesis of 3-ethynylphenol and protected 4-ethynylphenols. The complete synthesis of 3-phenylethynylphenol, 3-ethynylphenol, and protected 4-ethynylphenol in high yields has been demonstrated and is discussed herein. Three new phenylethynyl functionalized arylene ether matrix resins have been synthesized in high yields and purity by reacting 3-phenylethynylphenol with 4,4′-dichlorodiphenyl sulfone, 4,4′-difluorobenzophenone, and bis(4-fluorophenyl)phenyl phosphine oxide, via nucleophilic poly(arylene ether) synthesis conditions. These low molecular weight materials undergo thermally induced chain extension/branching to yield an insoluble three-dimensional network at reaction temperatures of around 380°C. The low molecular weight arylene ethers endcapped with the phenylethynyl group demonstrate excellent flow characteristics and a wide processing window of about 250°C. Crosslinking of the 4,4′-bis(3-phenylethynyl phenoxy)diphenyl sulfone system for 30 min at 350°C in air afforded a T_g value of 265°C by differential scanning calorimetry measurements. Trace metal analysis for palladium and copper showed absence of these metals that would otherwise detract from the excellent thermal stability. The synthesis and characterization of these phenylethynyl endcapped arylene ether matrix resins is discussed. © 1995 John Wiley & Sons, Inc.     

An NMR study of methanol diffusion in polymer electrolyte fuel cell membranes

Methanol diffusion in two polymer electrolyte membranes, Nafion 117 and BPSH 40 (a 40% disulfonated wholly aromatic polyarylene ether sulfone), was measured using a modified pulsed field gradient NMR method. This method allowed for the diffusion coefficient of methanol within the membrane to be determined while immersed in a methanol solution of known concentration. A second set of gradient pulses suppressed the signal from the solvent in solution, thus allowing the methanol within the membrane to be monitored unambiguously. Over a methanol concentration range of 0.5–8 M, methanol diffusion coefficients in Nafion 117 were found to increase from 2.9 × 10⁻⁶ to 4.0 × 10⁻⁶ cm² s⁻¹. For BPSH 40, the diffusion coefficient dropped significantly over the same concentration range, from 7.7 × 10⁻⁶ to 2.5 × 10⁻⁶cm² s⁻¹. The difference in diffusion behavior is largely related to the amount of solvent sorbed by the membranes. Increasing the methanol concentration results in an increase in solvent uptake for Nafion 117, while BPSH 40 actually excludes the solvent at higher concentrations. In contrast, diffusion of methanol measured via permeability measurements (assuming a partition coefficient of 1) was lower (1.3 × 10⁻⁶ and 6.4 × 10⁻⁷ cm² s⁻¹ for Nafion 117 and BPSH 40 respectively) and showed no concentration dependence. The differences observed between the two techniques are related to the length scale over which diffusion is monitored and the partition coefficient, or solubility, of methanol in the membranes as a function of concentration. For the permeability measurements, this length is equal to the thickness of the membrane (178 and 132 μm for Nafion 117 and BPSH 40 respectively) whereas the NMR method observes diffusion over a length of approximately 4–8 μm. Regardless of the measurement technique, BPSH 40 is a greater barrier to methanol permeability at high methanol concentrations.     

Rhodathiaboranes with `anomalous' electron counts: synthesis, structure and reactivity

Analysis of the structures of 8,8-(PPh₃)₂-8,7-nido-RhSB₉H₁₀ and 9,9-(PPh₃)₂-9,7,8-nido-RhC₂B₈H₁₁ by RMS misfit calculations has confirmed that these rhodaheteroboranes possess nido 11-vertex cluster geometries in apparent contravention of Wade's rules. However, examination of the molecular structures of both species shows that the {RhP₂} planes are inclined by ca. 66° with respect to the metal-bonded SB₃ or CB₃ faces, and that two weak ortho-CHRh agostic interactions occupy the vacant co-ordination position thereby created. As a consequence of these agostic bonds the Rh atom, and hence the overall cluster, is provided with an additional electron pair, meaning that their nido structures are now fully consistent with Wade's rules. The chelated diphosphine compound 8,8-(dppe)-8,7-nido-RhSB₉H₁₀ is similar to the PPh₃ compound in showing the same agostic bonding. Attempts to prepare a bis-P(OMe)₃ analogue result in ligand scavenging and the formation of 8,8,8-{P(OMe)₃}₃-8,7-nido-RhSB₉H₁₀. Similarly, reaction between Cs[6-arachno-SB₉H₁₂] and RhCl(dmpe)CO does not result in CO loss but in formation of 8,8-(dmpe)-8-(CO)-8,7-nido-RhSB₉H₁₀, shown to exist as a mixture of two of three possible rotamers. Deprotonation of 8,8-(PPh₃)₂-8,7-nido-RhSB₉H₁₀ and 8,8-(dppe)-8,7-nido-RhSB₉H₁₀ with MeLi yields the anions [1,1-(PPh₃)₂-1,2-closo-RhSB₉H₉]⁻ and [1,1-dppe-1,2-closo-RhSB₉H₉]⁻, respectively, with octadecahedral cage structures. It is argued that anion formation causes the agostic bonding to be `switched-off' and results in the cluster adopting the closo architecture predicted by Wade's rules. This structural change is fully reversible on reprotonation, and if reprotonation of [1,1-(dppe)-1,2-closo-RhSB₉H₉]⁻ is carried out in MeCN, the product 8,8-(dppe)-8-(MeCN)-8,7-nido-RhSB₉H₁₀ forms. Interestingly, 8,8-(dppe)-8-(MeCN)-8,7-nido-RhSB₉H₁₀ reconverts to 8,8-(dppe)-8,7-nido-RhSB₉H₁₀ on standing in CDCl₃, suggesting that the agostic bonding is sufficiently strong to displace co-ordinated MeCN. All new compounds are fully characterised by multinuclear NMR spectroscopy and, in many cases, by single crystal X-ray diffraction.     

Photoinitiated alternating copolymerization of dialkyl maleates and fumarates with vinyl ethers

A systematic study of the free radical photoinitiated alternating crosslinking copolymerizations of dialkyl maleates and furmarates with multifunctional vinyl ethers was carried out. The photocopolymerizations were fast and highly efficient when carried out using a variety of α‐cleavage photoinitiators. The effects of the structures of the both the unsaturated esters and the vinyl ether monomers were examined. Dialkyl maleates were observed to be more reactive than the corresponding fumarate esters. The photopolymerization rates of several of these comonomer pairs were compared with standard diacrylate and dimethacrylate monomers. A range of different physical properties can be obtained by varying the length of the alkyl chain on alcohol portion of the unsaturated ester monomer. Prospects for the use of these comonomer systems in UV curable coatings, adhesives, printing inks, and composites are discussed. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

The redox chemistry of sulfenic acids

A persistent triptycenyl sulfenic acid is used as a model for cysteine-derived and other biologically relevant sulfenic acids in experiments which define their redox chemistry. EPR spectroscopy reveals that sulfinyl radicals are persistent and unreactive toward O(2), allowing the O-H bonding dissociation enthalpy (BDE) of the sulfenic acid to be readily determined by equilibration with TEMPO as 71.9 kcal/mol. The E° (RSO?/RSO(-)) and pK(a) of this sulfenic acid are also reported.