Landesman–Lazer resonance problems and saddle point methods

We show how saddle point techniques can be used to obtain new results for general resonance problems of the type considered by Landesman and Lazer.     

Capabilities and limits of ICP-MS for direct determination of element traces in saline solutions

An ICP-MS method for the determination of ultra-traces of 24 Elements (Li, Be, Mg, Al, Cr, Mn, Co, Zn, Cu, Ga, As, Se, Rb, Sr, Mo, Ag, Cd, Sn, Sb, Ba, Tl, Pb, Bi, U) at ng/L to μg/L levels in highly saline solutions (up to 30 g/L NaCl) was developed. Calculated to the salt content of the samples, limits of detection at the sub-μg/kg level were obtained. This allows the measurement of samples like sea water, or clinical samples like urine, serum and whole blood, with few or without sample preparation and a drastic improvement to the limits of detection. Compared to the determination in solutions of 1 g/L NaCl the limits of detection in the original sample were improved by one order of magnitude. Improvements in instrumental stability are achieved by the use of an additional gas, that is introduced to the aerosol stream and avoids salt deposition in the aerosol tube of the torch, the use of High Matrix Content (HMC) cones, that show no clogging even at NaCl-concentrations up to 50 g/L. With this setup the long term stability for measurements with changing matrix concentrations is < 10% without and < 5% with use of an internal standard for the individual samples. Cleaning up is necessary after 2 days of operation. The direct analysis of the Nearshore Seawater Reference Material NRC-CNRC CASS3 showed a good agreement with the certified and measured concentrations. Elements, that do not suffer from an isobaric overlap of matrix compounds can be determined clearly at ng/L levels. Measurement of different matrix concentrations showed, that acceptable results can be achieved with a single calibration for concentrations from 5 g/L NaCl to 30 g/L NaCl, though matrix matching shows the best results.     

New AlDy(Ni,Co) glasses - the influence of pre-aging on decomposition and modelling of the crystallisation

The decomposition of AlDy₆Ni₁₀ and AlDy₈Ni₆Co₂ glasses prepared by melt spinning after different pre-aging regimes was investigated. The modelling of the transformation at the glass transition and the crystallisation was tested by a more general Johnson-Mehl-Avrami-Kolmogorov model and by the determination of the local kinetic parameter. The relaxation was tested with an lnt kinetic model after Gibbs.     

On operators and search space topology in multi-objective flow shop scheduling

Multi-objective optimization using evolutionary algorithms identifies Pareto-optimal alternatives or their close approximation by means of a sequence of successive local improvement moves. While several successful applications to combinatorial optimization problems are known, studies of underlying problem structures are still scarce.     

Differential effects of synchronous and asynchronous multifinger coactivation on human tactile performance

Background  

Repeated execution of a tactile task enhances task performance. In the present study we sought to improve tactile performance with unattended activation-based learning processes (i.e., focused stimulation of dermal receptors evoking neural coactivation (CA)). Previous studies show that the application of CA to a single finger reduced the stationary two-point discrimination threshold and significantly increased tactile acuity. These changes were accompanied by an expansion of the cortical finger representation in primary somatosensory cortex (SI). Here we investigated the effect of different types of multifinger CA on the tactile performance of each finger of the right hand.     

A new formula for the saddle-to-scission time

We propose a new formula for the saddle-to-scission time that is more general that the one based on Kramers' approach. Its validity and applicability is then studied in detail. Such a formula is useful for the evaluation of the fission time of very heavy nuclei.     

III-V compound semiconductor (001) surfaces

There has been renewed interest in the structure of III-V compound semiconductor (001) surfaces caused by recent experimental and theoretical findings, which indicate that geometries different from the seemingly well-established dimer models describe the surface ground state for specific preparation conditions. I review briefly the structure information available on the (001) surfaces of GaP, InP, GaAs and InAs. These data are complemented with first-principles total-energy calculations. The calculated surface phase diagrams are used to explain the experimental data and reveal that the stability of specific surface structures depends largely on the relative size of the surface constituents. Several structural models for the Ga-rich GaAs (001)(4×6) surface are discussed, but dismissed on energetic grounds. I discuss in some detail the electronic properties of the recently proposed cation-rich GaAs (001)ζ(4×2) geometry. Received: 18 May 2001 / Revised version: 23 July 2001 / Published online: 3 April 2002     

Isotopic production cross sections of residues in reactions induced by relativistic heavy ions with protons and deuterons

The isotopic production cross sections of heavy residues in relativistic heavy-ion collisions have been investigated in inverse kinematics. The primary reaction products were fully identified in mass and atomic number prior to beta decay using the fragment separator FRS. The huge collection of data obtained helps in the understanding of the two main reaction mechanisms involved: fragmentation and fission. These data provide basic information for future radioactive ion beam facilities and for technical applications like intense neutron sources by means of spallation targets.     

Towards a normative model for inventory cost management in a generalized ABC classification system

This paper establishes a general ABC inventory classification system as the foundation for a normative model of the maintenance cost structure and stock turnover characteristics of a large, multi-item inventory system with constant demand. For any specified number of inventory classes, the model allows expression of the overall system combined ordering and holding cost in terms of (i) the re-ordering frequencies for the items in each inventory class and (ii) the inventory class structure, that is, the proportion of the total system's items that are in each inventory class. The model yields a minimum total maintenance cost function, which reflects the effect of class structure on inventory maintenance costs and turnover. If the Pareto curve (a.k.a. Distribution-by-value function) for the inventory system can be expressed (or approximated) analytically, the model can also be used to determine an optimal class structure, as well as an appropriate number of inventory classes. A special case of the model produces a simply structured, class-based ordering policy for minimizing total inventory maintenance costs. Using real data, the cost characteristics of this policy are compared to those of a heuristic, commonly used by managers of multi-item inventory systems. This cost comparison, expressed graphically, underscores the need for normative modelling approaches to the problem of inventory cost management in large, multi-item systems.