Combination of RSM and NSGA-II algorithm for optimization and prediction of thermal conductivity and viscosity of bioglycol/water mixture containing SiO2 nanoparticles

The fluids containing nanoparticles have enhanced thermo-physical characteristics in comparison with conventional fluids without nanoparticles. Thermal conductivity and viscosity are thermo-physical properties that strongly determine heat transfer and momentum. In this study, the response surface method was firstly used to derive an equation for the thermal conductivity and another one for the viscosity of bioglycol/water mixture (20:80) containing silicon dioxide nanoparticles as a function of temperature as well as the volume fraction of silicon dioxide. Then, NSGA-II algorithm was used for the optimization and maximizing thermal conductivity and minimizing the nanofluid viscosity. Different fronts were implemented and 20th iteration number was selected as Pareto front. The highest thermal conductivity (0.576 W/m.K) and the lowest viscosity (0.61 mPa.s) were obtained at temperature on volume concentration of (80 °C and 2%) and (80 °C without nanoparticle) respectively. It was concluded that the optimum thermal conductivity and viscosity of nanofluid could be obtained at maximum temperature (80 °C) or a temperature close to this temperature. An increase in the volume fraction of silicon dioxide led to the enhancement of thermal conductivity but the solution viscosity was also increased. Therefore, the optimum point should be selected based on the system requirement.     

Direct effect of nanoparticles on the thermal conductivity of CuO-water nanofluid in a phase transition phenomenon using molecular dynamics simulation

Journal of Thermal Analysis and Calorimetry - The thermal behavior of CuO-water nanofluid is examined on an aluminum surface. The dimensions of simulation boxes are...     

Preparation of ethylene/α-olefins copolymers using (2-RInd)2ZrCl2/MCM-41 (R:Ph,H) catalyst,microstructural study

(2-RInd)₂ZrCl₂ (R:Ph,H) catalyst was supported on MCM-41 and ethylene copolymerization behavior as well as microstructure of copolymers were studied. A steady rate–time profile behavior was observed for homo and copolymerization of ethylene using supported catalysts. It was noticed that increasing the comonomer content can result in lower physical properties. The obtained results indicated that (2-PhInd)₂ZrCl₂/MCM-41 had higher ability of comonomer incorporation than the non-substituted supported catalysts. The CCC, CCE, and ECC (C: comonomer, E: ethylene) triad sequence distribution in backbone of copolymers were negligible, that means no evidence could be detected for comonomer blocks. The polymer characterization revealed that utilizing 1-octene instead of 1-hexene as the comonomer leads to more heterogeneous distribution of chemical composition. The heterogeneity of the chemical composition distribution and the physical properties were influenced by the type of comonomer and catalyst. (2-PhInd)₂ZrCl₂/MCM-41 produced copolymers containing narrower distribution of lamellae (0.3–1 nm) than the copolymer produce using Ind₂ZrCl₂/MCM-41 (0.3–1.6 nm).     

New Polydentate Trimethylsilyl Chalcogenide Reagents for the Assembly of Polyferrocenyl Architectures

A series of polychalcogenotrimethylsilane complexes Ar(CH₂ESiMe₃)_n, (Ar=aryl; E=S, Se; n=2, 3, and 4) can be prepared from the corresponding polyorganobromide and M[ESiMe₃] (M=Na, Li). These represent the first examples of the incorporation of such a large number of reactive ?ESiMe₃ moieties onto an organic molecular framework. They are shown to be convenient reagents for the preparation of the polyferrocenylseleno‐ and thioesters from ferrocenoyl chloride. The synthesis, structures, and spectroscopic properties of the new silyl chalcogen complexes 1,4‐(Me₃SiECH₂)₂(C₆Me₄) (E=S, 1 ; E=Se, 2 ), 1,3,5‐(Me₃SiECH₂)₃(C₆Me₃) (E=S, 3 ; E=Se, 4 ) and 1,2,4,5‐(Me₃SiECH₂)₄(C₆H₂) (E=S, 5 ; E=Se, 6 ) and the polyferrocenyl chalcogenoesters [1,4‐{FcC(O)ECH₂}₂(C₆Me₄)] (E=S, 7 ; E=Se, 8 ), [1,3,5‐{FcC(O)ECH₂}₃(C₆Me₃)] (E=S, 9 ; E=Se, 10 ) and [1,2,4,5‐{FcC(O)ECH₂}₄(C₆H₂)] (E=S, 11 illustrated; E=Se, 12 ) are reported. The new polysilylated reagents and polyferrocenyl chalcogenoesters have been characterized by multinuclear NMR spectroscopy (¹H, ¹³C, ⁷⁷Se), electrospray ionization mass spectrometry and, for complexes 1 , 2 , 3 , 4 , 7 , 8 , and 11 , single‐crystal X‐ray diffraction. The cyclic voltammograms of complexes 7 – 11 are presented.     

Propane-1,2,3-triyl tris(hydrogen sulfate): A mild and effcient recyclable catalyst for the synthesis of biscoumarin derivatives in water and solvent-free conditions简

A simple, efficient, and ecofriendly procedure has been developed using propane-l,2,3-triyl tris（hydrogen sulfate） as a catalyst for the synthesis of biscoumarin derivatives in water and solvent-free conditions. The significant features of the present protocol are simplicity, environmentally benign, high yields, no chromatographic separation, and recyclability of the catalyst.     

A numerical study on the effect of static magnetic field on the hemodynamics of magnetic fluid in biological porous media

Journal of Thermal Analysis and Calorimetry - High interstitial fluid pressure in the tumor is among the most important barriers to drug delivery. The use of the static magnetic field is one of the...     

3D Printing in analytical sample preparation

In the last 5 years, additive manufacturing (three‐dimensional printing) has emerged as a highly valuable technology to advance the field of analytical sample preparation. Three‐dimensional printing enabled the cost‐effective and rapid fabrication of devices for sample preparation, especially in flow‐based mode, opening new possibilities for the development of automated analytical methods. Recent advances involve membrane‐based three‐dimensional printed separation devices fabricated by print‐pause‐print and multi‐material three‐dimensional printing, or improved three‐dimensional printed holders for solid‐phase extraction containing sorbent bead packings, extraction disks, fibers, and magnetic particles. Other recent developments rely on the direct three‐dimensional printing of extraction sorbents, the functionalization of commercial three‐dimensional printable resins, or the coating of three‐dimensional printed devices with functional micro/nanomaterials. In addition, improved devices for liquid–liquid extraction such as extraction chambers, or phase separators are opening new possibilities for analytical method development combined with high‐performance liquid chromatography. The present review outlines the current state‐of‐the‐art of three‐dimensional printing in analytical sample preparation.     

Position calculation of the frequency band gap in the finite photonic crystal with multiple alternations using boundary element method

In this paper, the wave transmission from finite photonic crystals with multiple alternations is investigated using boundary element method (BEM). Since that, in these structures the alternation is not in all directions of space; the investigations of the frequency band gap with desired accuracy are not practical by analytical methods. Also, the frequency dispersion of dielectric rods is an effective parameter in photonic crystals, which this effect in our calculations has been considered. Due to the high capabilities of the BEM, the transmitted wave spectrum in the photonic crystal is calculated by changing the geometrical and optical parameters of the photonic crystal and applying more alternation in its structure and the position and width of the frequency band gap is investigated. Then, it is assumed that the photonic crystal with an arbitrary angle is rotated around the axis which is perpendicular on the crystal cross section and then, it is irradiated with a plan wave. The band gap of the photonic crystals with the desired structure, desired rotation angle and multiple alternations have been solved. Very low information volume, high speed and accuracy during the calculation and useable for any desired structures are the characteristics of this method.