Effect of biotransformation on multispecies plume evolution and natural attenuation

Biological transformation of volatile organic compounds is one of the key factors that influence contaminant-plume evolution and thus natural attenuation. In this study we investigate the effect of biological transformation on the transport of contaminants in the aqueous and gaseous phases. The analysis includes the study of the effect of density-driven advection of contaminants in the gaseous phase on multiphase and multispecies flow, fate and transport modeling in the subsurface. Trichloroethylene (TCE) and its two byproducts, dichloroethylene and vinyl chloride, are analyzed as the target contaminants. Our results indicate that density-driven advection of the gaseous phase, which is initiated by evaporation of TCE as a nonaqueous phase liquid, increases the downward and also the lateral migration of TCE within the unsaturated zone. This process also influences the location of high-concentration zones of the byproducts of TCE in the unsaturated and the saturated zones. Biotransformation of TCE contributes to the reduction of dissolved TCE plume development as expected. The daughter byproducts, which are introduced into the subsurface system, show distinct transport patterns as they are affected by their independent degradation kinetics and density-driven advection. These observations, which are based on our simulation results for biotransformation and transport of TCE and its byproducts, are useful in evaluating the natural attenuation processes, its potential health hazards and also the evaluation of potential plume development at contaminated sites.     

Predicting the onset of DNA supercoiling using a non-linear hemitropic elastic rod

Elastic rod models provide a means to interpret single molecule DNA experiments as well as predict DNA behavior under physiological conditions. Here we use an elastic rod model to predict the stability boundary (critical torque vs. applied tension) for single molecule DNA experiments in which the molecule is subjected to applied tension and twist. We discuss the shortcomings of the usual isotropic rod model. We then derive a consistent non-linear material law from the general representation for a hemitropic (chiral) rod. Finally, we present results of a standard bifurcation analysis predicting the stability boundary. We find results from the non-linear hemitropic rod to match the data closely.     

Analysis of thermally induced multistable composites

This paper models the non-linear flexural response of laminates that have piecewise variation of lay-up in the planform, using finite element analysis. Attention is focused on the effects that thermal stresses have on the potential multiple shapes of a composite structure. Unsymmetric laminates may possess more than a single equilibrium configuration, and during the cool-down the solution thus bifurcates at a critical temperature. In static analyses, numerical solutions are often coaxed to converge into one or the other branch of the solution. A methodology to overcome this problem is presented. Such modelling is necessary to allow application of multistable composite within morphing aircraft structures as multistable composites could provide a viable solution for the realisation of shape-adaptable structures.     

Feedback stabilization of snap-through buckling in a preloaded two-bar linkage with hysteresis

We study a linearly damped preloaded two-bar linkage that exhibits hysteresis due to the presence of multiple attracting equilibria. The dynamics at the unstable equilibrium, through which a snap-through buckle occurs, are not linearizable due to a solution-dependent singularity. We stabilize the unstable equilibrium using two distinct non-linear controllers. The feedback-linearization controller requires knowledge of the linkage parameters, whereas the robust version of the intrinsic non-linear proportional-derivative controller requires only an upper bound on the stiffness.     

Ductile–brittle transitions in the fracture of plastically deforming,adhesively bonded structures. Part II: Numerical studies

To enable the effective and reliable use of structural adhesive bonding in automotive applications, the cohesive properties of a joint need to be determined over a wide range of loading rates. In this paper, a strategy for determining these properties has been described and used to analyze a set of experimental results presented in a companion paper. In the particular system studied, a crack growing in a toughened quasi-static mode could make a catastrophic transition to a brittle mode of fracture. The cohesive parameters for both the toughened and brittle modes of crack growth were determined by comparing numerical predictions from cohesive-zone simulations to the results of experimental tests performed using double-cantilever beam specimens and tensile tests. The cohesive parameters were found to be essentially rate-independent for the toughened mode, but the toughness dropped by a factor of four upon a transition to the brittle mode. The results of wedge tests were used as an independent verification of the cohesive parameters, and to verify that the quasi-static properties remained rate-independent to very high crack velocities corresponding to conditions of low-velocity impact. The effects of friction, and the use of the wedge test to determine cohesive parameters, were also explored.     

Geometry and electronic structure of a heterometallic cluster Mo<Subscript>2</Subscript>Mg<Subscript>2</Subscript> in different oxidation states of Mo: a DFT study

Reduction of tetranuclear heterometallic complex Mo₂Mg₂ was simulated using the B3LYP and PBE density functional methods. The results of geometry calculations of the initial complex [Mo^VIO₂Mg(MeOH)₂(OMe)₄]₂ and a partially reduced Mo^V complex are in good agreement with experimental data. The reduced Mo^III complex is characterized by a decrease in the binding energy of aqua ligands. Structural rearrangement of the complex with release of a coordination position at the Mo atoms requires small energy expenditure. One can assume that the reduction of the polynuclear complex causes overcrowding of its coordination sphere, which favors formation of dinitrogen complexes. Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 3, pp. 441–457, March, 2008.     

Thermal degradation of composites of poly(methyl methacrylate) with alkoxysilane hydrolyzates

Organic-inorganic composites of poly(methyl methacrylate) with alkoxysilane hydrolyzates form transparent films. Their thermal and oxidative thermal degradation were studied by differential scanning calorimetry and thermogravimetric analysis.     

On calculation of the distribution coefficient from the results of continuous gas extraction of a volatile component from a liquid mixture

Distribution coefficient of a volatile component among the liquid and gas phases was calculated from equidistant data on continuous gas extraction by using an equation generalizing the relations available in the literature.