Chemical vapor discrimination using a compact and low-power array of piezoresistive microcantilevers

A compact and low-power microcantilever-based sensor array has been developed and used to detect various chemical vapor analytes. In contrast to earlier micro-electro-mechanical systems (MEMS) array sensors, this device uses the static deflection of piezoresistive cantilevers due to the swelling of glassy polyolefin coatings during sorption of chemical vapors. To maximize the sensor response to a variety of chemical analytes, the polymers are selected based on their Hildebrand solubility parameters to span a wide range of chemical properties. We utilize a novel microcontact spotting method to reproducibly coat a single side of each cantilever in the array with the polymers. To demonstrate the utility of the sensor array we have reproducibly detected 11 chemical vapors, representing a breadth of chemical properties, in real time and over a wide range of vapor concentrations. We also report the detection of the chemical warfare agents (CWAs) VX and sulfur mustard (HD), representing the first published report of CWA vapor detection by a polymer-based, cantilever sensor array. Comparisons of the theoretical polymer/vapor partition coefficient to the experimental cantilever deflection responses show that, while general trends can be reasonably predicted, a simple linear relationship does not exist.     

A Simple Primary Amide for the Selective Recovery of Gold from Secondary Resources

Waste electrical and electronic equipment (WEEE) such as mobile phones contains a plethora of metals of which gold is by far the most valuable. Herein a simple primary amide is described that achieves the selective separation of gold from a mixture of metals typically found in mobile phones by extraction into toluene from an aqueous HCl solution; unlike current processes, reverse phase transfer is achieved simply using water. Phase transfer occurs by dynamic assembly of protonated and neutral amides with [AuCl₄]^? ions through hydrogen bonding in the organic phase, as shown by EXAFS, mass spectrometry measurements, and computational calculations, and supported by distribution coefficient analysis. The fundamental chemical understanding gained herein should be integral to the development of metal‐recovery processes, in particular through the use of dynamic assembly processes to build complexity from simplicity.     

Exploring Regioselective Bond Cleavage and Cross‐Coupling Reactions using a Low‐Valent Nickel Complex

Recently, esters have received much attention as transmetalation partners for cross‐coupling reactions. Herein, we report a systematic study of the reactivity of a series of esters and thioesters with [{(dtbpe)Ni}₂(μ‐η²:η²‐C₆H₆)] (dtbpe=1,2‐bis(di‐tert‐butyl)phosphinoethane), which is a source of (dtbpe)nickel(0). Trifluoromethylthioesters were found to form η²‐carbonyl complexes. In contrast, acetylthioesters underwent rapid C_acyl?S bond cleavage followed by decarbonylation to generate methylnickel complexes. This decarbonylation could be pushed backwards by the addition of CO, allowing for regeneration of the thioester. Most of the thioester complexes were found to undergo stoichiometric cross‐coupling with phenylboronic acid to yield sulfides. While ethyl trifluoroacetate was also found to form an η²‐carbonyl complex, phenyl esters were found to predominantly undergo C_aryl?O bond cleavage to yield arylnickel complexes. These could also undergo transmetalation to yield biaryls. Attempts to render the reactions catalytic were hindered by ligand scrambling to yield nickel bis(acetate) complexes, the formation of which was supported by independent syntheses. Finally, 2‐naphthyl acetate was also found to undergo clean C_aryl?O bond cleavage, and although stoichiometric cross‐coupling with phenylboronic acid proceeded with good yield, catalytic turnover has so far proven elusive.     

Recent Advances in the Deoxydehydration of Vicinal Diols and Polyols

Deoxydehydration (DODH) is one of the most promising tools to reduce the oxygen content of biomass (sugars and polyols) and provide analogues of platform chemicals that are derived from fossil resources. This reaction converts a vicinal diol into an alkene and is typically catalyzed by high‐oxidation‐state metal‐oxo compounds in the presence of a stoichiometric reductant, with examples of both homogeneous and heterogeneous systems. This minireview will highlight the developments in this field over the past 5 years and focus on efforts to solve the problems that currently prevent DODH being performed on a commercial scale, including the nature of the reductant, substrate scope and selectivity, and catalyst recovery and expense.     

Selective oxo functionalization of the uranyl ion with 3d metal cations

The linear uranyl dication [UO2]2+ can be bound in one of two coordination sites in the ditopic Pacman-shaped pyrrolic macrocyle H4L. Incorporation of Mn2+, Fe2+, or Co2+ cations in the second donor compartment affords the first uranyl complexes with a transition-metal-functionalized oxo group.     

Rapid discovery of potent siRNA-containing lipid nanoparticles enabled by controlled microfluidic formulation

The discovery of potent new materials for in vivo delivery of nucleic acids depends upon successful formulation of the active molecules into a dosage form suitable for the physiological environment. Because of the inefficiencies of current formulation methods, materials are usually first evaluated for in vitro delivery efficacy as simple ionic complexes with the nucleic acids (lipoplexes). The predictive value of such assays, however, has never been systematically studied. Here, for the first time, by developing a microfluidic method that allowed the rapid preparation of high-quality siRNA-containing lipid nanoparticles (LNPs) for a large number of materials, we have shown that gene silencing assays employing lipoplexes result in a high rate of false negatives (~90%) that can largely be avoided through formulation. Seven novel materials with in vivo gene silencing potencies of >90% at a dose of 1.0 mg/kg in mice were discovered. This method will facilitate the discovery of next-generation reagents for LNP-mediated nucleic acid delivery.     

A simple and robust LC-MS/MS method for quantification of free 3-nitrotyrosine in human plasma from patients receiving on-pump CABG surgery

We have developed a simple, sensitive, and robust liquid chromatography-mass spectrometry/mass spectrometry (LC-MS/MS) method to determine free 3-nitrotyrosine concentrations in human plasma of patients receiving on-pump coronary artery bypass grafting surgery. A one-step solid-phase extraction protocol was optimized to enrich the analyte at low nanomolar concentrations. The processed samples were analyzed by LC-MS/MS with a 2.1 × 100 mm Kinetex PFP column and a triple quadrupole mass spectrometer. The method was validated for 3-nitrotyrosine concentrations close to real patient plasma levels. The relative standard deviations or relative errors of the intraday and interday determinations were all within 10%. Limit of detection and limit of quantitation were determined to be 0.034 nM and 0.112 nM, respectively, while lower limit of quantitation was below 0.625 nM. No deterioration of the column performance was noticed after running a large number of patient samples. The results showed that the 3-nitrotyrosine concentrations in coronary sinus plasma samples were elevated after cardiopulmonary bypass (CPB) procedure. The pre-CPB and post-CPB concentrations of 3-nitrotyrosine in patient plasmas were 1.494 ± 0.107 nM and 2.167 ± 0.177 nM (mean ± SEM), respectively. Application of this method to more patients in clinical studies may help validate 3-nitrotyrosine as a meaningful biomarker for nitrosative stress and link patient characteristics, clinical outcomes, and cardioprotective treatments to endogenous nitrosative stress levels.     

Azine Synthesis via Nitrogen-Nitrogen Bond Formation

Imine anions, generated by reaction of nitrites with organometallic reagents, are dimerized to form symmetrical azines through the use of CuI and t-butyl peroxybenzoate.